Comgo Z1 Laser Setup In LightBurn and Laser GRBL
HTML-код
- Опубликовано: 29 сен 2024
- Detailed setup in Laser GRBL and LightBurn of the Comgrow Comgo Z1 10 watt laser engraver.
Also included is how to adjust the hard limits, if needed.
Links to items used: (Disclosure: I do receive a small commission if you purchase any of these items. This does not increase your cost)
Comgrow Z1 Laser Engraver 10W Output Power amzn.to/3pCVIAJ
Direct from Comgrow: www.comgrow.co...
Facebook: / comgrow
Hey Roger. I appreciate you helping me. I was able to get the laser up and running and making some art. It was working fine until I dropped my computer and it broke. I got a new one and now the new "same exact computer" currently won't connect to laser grbl. Do you have any ideas as to why? I have looked for troubleshooting answers and I haven't been able to progress.. any advice would be appreciated.
Make sure the CH340 driver is installed on the new computer. Without it, it will not connect.
Hi I just got mine and i installed the drivers from the micro sd, and grbl... mine will not connect to my windows 11pc yet... should i go to the site for drivers and grbl.... or is it true what some say about 1)enabling the dtr signal or 2 raising the baud rate? Thank you Sir
Make sure you have the latest CH340 driver installed.
@@rogersshop will do
Hello Roger, have you had your z1 comgrow module stop firing , Mine is not firing, waitng for comgrow to get back to me. I enjoy your videos, your very knowledgeable about laser..I updated the firmware already, any thoughts,,Thanks Dave
Make sure the laser head connection is tight. I've had this come loose before (not on this laser) and even though it looked connected, it was not.
Very helpful video! I was able to get lasergrbl working (though it took me a while to figure out how to change the laser power and speed). I had a heck of a time with lighburn.. With the help of your video I was able to to figure it out. Thanks!
Haven’t used mine in a couple of months, Lightburn software, issues with homing and not going to origin, any suggestions? Thank you
Need more details. That is a little vague.........
@@rogersshop sorry about that apparently having a senior moment, got it figured out.
I do see the link to the file for uploading the grid?
The layout grid is not part of this video, but can be found here: moonshinecrafts.com/product-category/laser-project-downloads/
Okay thanks! I got it working! Except the Y Axis isn't working right now... is there an answer to this problem? Or a link?
@@johnhart476 Check your cable connections
I have a question for the retired electrician.. Limit switches... Normally closed, right? The Comgo Z1 only has limit switches in order to home the machine.. If I wire them in series, I could add extra limit switches for the other end of the X and Y axis to protect the machine from crashing if I do something dumb.. What do you think?
It depends............ Can be either N.O. or N.C., depending on how the firmware is written.
@@rogersshop understood.. I can check with my multimeter. If NC, it would work I think.. Tripping either one would break the circuit.
@@ericeinsmann5559 Yes. If N.O. then could be connected in parallel. N.C. would need to be in series.
In your video you mention that you would put a link in the description of the video for the grid file you used. Is that something that you are able to share?
Spoil board grid source: www.thingiverse.com/thing:4917083 in this video: ruclips.net/video/aQCodEjY_RY/видео.html
Hi Roger, thank you for your video. I'm struggling engraving this grid. The lower right corner keep hitting the hard limit. If I move the limit switch barely enough to make it work I end up hitting the screws of the power supply while the laser is traveling. I really think the design could have been better with the positioning of that power supply... Any suggestions? thank you.
Is it true that to install the software you need 8GB of ram?
love your videos! Mine goes to far to the left, have no clue how to fix that
05:04 lightburn instructions starts here
No luck with Lightburn and Comgrow. Feel free to delete again.
Only delete comments if contains profanity.
Mine won’t connect at all
Try a different USB cable. Had this happen before (not with this, but has happened)
@@rogersshop same issue here. It won't connect at all
What is the name of the cable? It's not an average USB because one of the ends is specific for that device.. right? Can I get this cable from amazon?
FYI for any new users that cannot get it to connect. Mine would not connect with stock settings. I had to change from the stock 115600 Baud to 921600 Baud or it would not connect.
Just to add, Light Burn will not work on my machine but grbl will. Not sure what to do at this point. Any ideas would be helpful. So far I've uninstalled and reinstalled everything. Changed COM ports, removed and manually setup a few times as well, still waiting for connection.
I am having this problem as well. I am using windows 11. Not sure why it won't connect.. some help would be awesome!
hey tryign to figure out how you start from center and set origin, how did you get the laser to the center to set the origin in the first place? just use the X/Y and then move to then set origin? wondering for when i get my Ray5 in .
What model Ray 5? If the 5 or 10 watt, it will not have limit switches, so the best way is to use "Current Position" as a start point (from center), and set the laser head manually to the center point before starting. If the 20 Watt, it will have limits and a homing function. Here, use Absolute Coordinates, place project in center of workspace, frame, and go. Make sure you are starting from Home here, and not a random spot.
@@rogersshop i have the 20 watt, with 5watt module ( their dual laser head sale) so i should use the homing feature and just start from home (the 0,0 coordinate)? sorry to pester, just want to make sure i am understanding correctly.
@@62saki91 5 and 10 watt base models do not have limit switches, so homing is not an option. The 20 watt does have limits, and it will home in front left (0, 0)
@@rogersshop so with the 20 watt model, before starting, home it to 0,0 and start from there with absolute coordinates?, even if project is in the center?
@@62saki91 Yes. Just make sure your project is centered in the workspace and always frame the project first.