There should be a miss-fit calculation first to check that the pull up the flange together will not introduce cold stress on the pipe especially when it is adjacent of strain sensitive equipment. Piping code, i.e, ASME B31.3 also provide limitation ofmiss alignment, also in ASME PCC-1. As long as the miss alignment is within the tolerance, i would use this tools.
Is this correct way, during inspection the owner may ask you to remove the bolt to check whether external load acting in bolt ? and pipe are in align..
I know old comment but in the 8 plus years I've been doing this type of work not once did they make us do that. It could happen to some places but never at the plants i was in.
now you're just putting a load on the bolts to handle that misalignment. When someone eventually has to do maintenance on that flange its going to spring back
If two flanges meet about 15-20 mm out of center a new pipe fitting contractor should be found. To me a misalignment of that magnitude is unacceptable. By using this method of alignment, the flange faces will be out of parallel which can have devastating consequences for the sealing of the gasket. Furthermore, a non-negligible shear stress on the bolts could mean a blown bolt.
how do u put gasket on the flanges if the gap is too tight? obviously this tool need some improvement in order to complete the jobs..should have another pusher to make the gap between the flanges opened to allow you put the gasket on it..
A solution to a problem that shouldn't be there in the first place. Tension on the bolts and a very slight difference between the top and bottom of the flange
Im pipe fitter and they said very good!I dont know who invented this crap.When you are good with pipeing and calculation this things will not happend to you.Even when happen there is 100more simplier solutions.
Me To be fair to these wildly stupid inventions. Over time settling and vibration cause misalignment so putting pipe back in service needs alignment tools. But I would never waste company money on this garbage.
Это помещение очень далеко от реальности. Слишком много места, фланец как на витрине, трубопрод не промаркирован, отсутствует стрелка направления движения среды, отсутствует цветная маркировка среды, фланец почему-то смещен только в одной плоскости, освещённость рабочего места идеальная. И последнее, ремонтник не может быть в такой чистой робе. Этот просто какая-то операционная и хирург, только маску осталось одеть.
Смотрится круто. Круто как для рекламы. Но очень далеко от реалий жизни. Идеальные ровные участки труб) Одна только изоляция какие приносит не удобства. Вообще весь процесс монтажа у нас труб. От А до Я. Сравним с карикатуркой про три обезьяны.
If the pipe is misaligned that much I’d take a look at fabrication before forcing it into place, the stresses that could be applied during process may be a problem if forced the 3 inches into position, I wouldn’t accept it during the inspection line walk.... or use of these tools to hide bad fitting/ fabrication... just sayin
Alex Carling really? And what do you make a career doing? I have 20 years experience working on every continent on the planet, off and on shore, with a degree in engineering and a full apprenticeship in pipe fitting and fabrication, building gas and petrochemical plants, FPSOs, oil rigs And pipelines, now in a client position and have been for been for a decade making well into 6 figures a year... think I’ve got a fair idea what I’m talking about, but by all means, tell me what you know about me and piping.... asshole
Alex Carling the fact that your response was that tells me you aren’t even in the industry and are nothing but a troll lol as I type this I sit on a balcony over looking the med awaiting a weekend to begin, while you sit in your parents basement or shitty apartment somewhere wishing you had done more with your life, if not Alex, I know your name and if, and that’s a big if, you are in the industry we will no doubt cross paths and I’ll no doubt be your boss... sayin that you probably will never make it to any real project and will remain in the same yard or fab shop until retirement, happy trail asshole, let me know how that goes for ya
Alex Carling ha ha ha I didn’t want to taken it your level but you are nothing but a fuck boy, you have no idea what your talking about and your opinions on this feed don’t mean shit, your just one of life’s losers, too bad for ya, this started off as an educated adult comment about equipment used in the industry and you’ve done nothing but try to troll ha ha ha Everything I wrote has been the truth and you seem like your the butt hurt one because you’ll never achieve fuck all in life, a jealous little insignificant man with nothing to offer, I hope you die in a car fire and your parents die in one to on the way to your funeral ya prick
There should be a miss-fit calculation first to check that the pull up the flange together will not introduce cold stress on the pipe especially when it is adjacent of strain sensitive equipment. Piping code, i.e, ASME B31.3 also provide limitation ofmiss alignment, also in ASME PCC-1.
As long as the miss alignment is within the tolerance, i would use this tools.
We have many solution for this issue without any equipment.
But this issue mean we have problem during the fabrication or during welding operations
Yup, nailed it. Code determines if you can do this. Not with gas of any kind. 👍
Well done!I wrote something similiar
Describe at least one.
Conditions are
1. internal / external .coated .
@Alex Carling I didn't get u !! Was dat for me?
A hammer and a spud wrench are cheaper, faster and just as effective.
Time is money, spud is so much quicker.
Union jobs....
Agree!!
@@mattarmstrong2515 rat
If you're using a hammer... thread on the screw can be damage
What about stresses induces to piping system and equipment attached.
How about the pipe stress if you do that by force?
What about the uneven tilt this creates? You can clearly see at 2:56 the gap at the top is larger than the gap at the bottom.
Now how do you put the gasket in between if it is to tight.
Banana wedges
Now to only put the Gasket in...
That's the first of many thoughts I had about this. If we fuck up a measurement we cut it apart and do it again. None of this half ass stuff.
To be used only for mild misalignment, else bolts will be under tension and flange will leak
when we use this tool, how to insert gasket?
Doing alignment by this tool, the joint will be in tension.
Please friends what is the name of that tool they use to bringing the pipe to level.
Mksh tutorial nya,,, semangat terus bosku
Awesome tool
Just like companies that make fishing gear. They aren't in business to catch fish just fishermen.
Correct
Is this correct way, during inspection the owner may ask you to remove the bolt to check whether external load acting in bolt ? and pipe are in align..
I know old comment but in the 8 plus years I've been doing this type of work not once did they make us do that. It could happen to some places but never at the plants i was in.
Or you could just hire competent pipe fitters
That's more than slight dog
Obviously youre not one.
Nothing to do with pipe fitters. It’s to do with misalignment, alignment pins are the best.
We used line up bars or for big pipe a choker and rachet or chain fall
Why are flange added to pipe?
Very good very nice 🙂
Оно все красиво в лаборатории, в жизни часто бывает , что данную приблуду хрен куда всунешь, обычный лом и отборный мат все решают.
now you're just putting a load on the bolts to handle that misalignment. When someone eventually has to do maintenance on that flange its going to spring back
How if i want to buy this tool..im from indonesia...thank i
See video description
My spud crescent wrench works awesome too
good spike its all what U need
I need this pls send me the equalizer ill make videos in real life refinery and shop work
Why not use barrel drifts?
In brazil these "gambiarra" is called "batoque or dog" ,used for other puproses , example when need aligment sttel plate , for weld ,
Nice trick
If two flanges meet about 15-20 mm out of center a new pipe fitting contractor should be found. To me a misalignment of that magnitude is unacceptable. By using this method of alignment, the flange faces will be out of parallel which can have devastating consequences for the sealing of the gasket. Furthermore, a non-negligible shear stress on the bolts could mean a blown bolt.
Домкрат не пробывали?
We have them there called comealongs and slings work every time!!!!!
Reality is something different
how do u put gasket on the flanges if the gap is too tight? obviously this tool need some improvement in order to complete the jobs..should have another pusher to make the gap between the flanges opened to allow you put the gasket on it..
Banana wedges and the gasket will drop right in
Nice welds
I'd worry about the quality of the welding first
What if the holes are mismatched?? Any solution
tarique mallick if you didn’t 2 holed the flanges you’re pretty much butt fucked
Cut spin weld 😁
Weld the holes closed and drill new ones
Blame the fabricator or the engineer. Cut the flange off and weld on the proper flange.
Cut it apart, 2 hole it, and do it right....
nicevideo
A solution to a problem that shouldn't be there in the first place. Tension on the bolts and a very slight difference between the top and bottom of the flange
Да ну на..., А как же лом, кувалда и епттвоюмат. Но если серьёзно приблуда хорошая, ...наверно)
Very well
Fabulous
А где же всеми любимая монтировка..
А прокладку как запихать?
Awesome
Cute but line up bar and floor jack do same thing!!!!
No gasket?
isto se resolve com duas espinas
Как можно было так опошлить идею традиционной кувалды?!
I’d fire a guy if he came to my job with that piece of crap instead of some spuds, a jack or a come along lol
Good
I want to talk about the welds in the first demonstration 😫
Colin Stark 😂😂 that’s the first thing I said
That's surely an apprentice having a practice!
those gloves are freaking everywhere your neighbors your co workers and your dog has them
👍👍👍
Some body tell me he's not using a torque wrench at 1:32
What is the name of this equipment
I was thinking a basic bottle jack..
Im pipe fitter and they said very good!I dont know who invented this crap.When you are good with pipeing and calculation this things will not happend to you.Even when happen there is 100more simplier solutions.
Me To be fair to these wildly stupid inventions. Over time settling and vibration cause misalignment so putting pipe back in service needs alignment tools. But I would never waste company money on this garbage.
Is this really neccesary?
HYDRAULIC JACK UNDER MOST MISMATCH FLANGE. THATS MORE EASE BUT TAKEN CARE ABOUT STRESS.
Это помещение очень далеко от реальности. Слишком много места, фланец как на витрине, трубопрод не промаркирован, отсутствует стрелка направления движения среды, отсутствует цветная маркировка среды, фланец почему-то смещен только в одной плоскости, освещённость рабочего места идеальная. И последнее, ремонтник не может быть в такой чистой робе. Этот просто какая-то операционная и хирург, только маску осталось одеть.
Это же что-то вроде рекламы. Наверное поэтому!)
looks nifty sure, but i dont see myself having time for all that in a turn around.
Сатнехник Вася с помощью лома быстрее сделает.
Знаем. АвтоВаз тоже на Васях держится.
Or to head this problem off you can fire your fitter and welder.
Да красиво и безопасно. У нас перекос с энерпаком делает. Тоже такой аппарат, но гидролически ражим не соединяется. Класс это безопасно.
I can smell the fresh paint
You ever try that on a pinch valve? Lol good luck!
Ese proceso esta mal el enfrentamiento de las bridas debe estar libre de tensión ....
便利そうだけど結構用途が限定的。
Finns dornspett!!
Смотрится круто. Круто как для рекламы. Но очень далеко от реалий жизни. Идеальные ровные участки труб) Одна только изоляция какие приносит не удобства. Вообще весь процесс монтажа у нас труб. От А до Я. Сравним с карикатуркой про три обезьяны.
Don't look strong enough to use on maintenance projects for shore
Thing looks cheap how many pipe alignments does 1 get before it breaks. Remember it's going to be in the dirt and everything
Они пластиковые? Всё ничего но как то не внушает доверие этот ремешок.
If you go those big misaligned flanges you got bigger problems won't be able to pass that from the foreman.
Just use a podger.
Put a come along on there that's how you do it when you can't build it to just drop bolts in.
I just don't understand the purpose of the torque wrench. There is no need in it if all your doing is lining up the flanges
I will line this flange and fit all the bolts max 30 mins
домкрат берёшь и всё! не надо ничего придумывать
🎉
Use a ratchet podger and you're eyes
If the pipe is misaligned that much I’d take a look at fabrication before forcing it into place, the stresses that could be applied during process may be a problem if forced the 3 inches into position, I wouldn’t accept it during the inspection line walk.... or use of these tools to hide bad fitting/ fabrication... just sayin
Alex Carling really? And what do you make a career doing? I have 20 years experience working on every continent on the planet, off and on shore, with a degree in engineering and a full apprenticeship in pipe fitting and fabrication, building gas and petrochemical plants, FPSOs, oil rigs And pipelines, now in a client position and have been for been for a decade making well into 6 figures a year... think I’ve got a fair idea what I’m talking about, but by all means, tell me what you know about me and piping.... asshole
Alex Carling the fact that your response was that tells me you aren’t even in the industry and are nothing but a troll lol as I type this I sit on a balcony over looking the med awaiting a weekend to begin, while you sit in your parents basement or shitty apartment somewhere wishing you had done more with your life, if not Alex, I know your name and if, and that’s a big if, you are in the industry we will no doubt cross paths and I’ll no doubt be your boss... sayin that you probably will never make it to any real project and will remain in the same yard or fab shop until retirement, happy trail asshole, let me know how that goes for ya
Alex Carling ha ha ha I didn’t want to taken it your level but you are nothing but a fuck boy, you have no idea what your talking about and your opinions on this feed don’t mean shit, your just one of life’s losers, too bad for ya, this started off as an educated adult comment about equipment used in the industry and you’ve done nothing but try to troll ha ha ha
Everything I wrote has been the truth and you seem like your the butt hurt one because you’ll never achieve fuck all in life, a jealous little insignificant man with nothing to offer, I hope you die in a car fire and your parents die in one to on the way to your funeral ya prick
Sledgehammer will work just fine
Spud wrench
I am no welder but those welds were nothing to write home about.
#drivenikhil
Civil engineering ke kaam h ye
Waao it’s Engineering
лучше моим слесарям это не показывать
塩ビやったら割れそうでこわいなー
Лом и кувалда и в раз пяток быстрее все будет сделано
Pin wrench bro
It's way more fun to flog in carrot slides with a massive hammer
Трубы под напряжением стягивать нельзя
It’s just a fancy screw dog with a ratchet strap.
Am I the only one who saw the real problem? wtf is that snot on the top flange to pipe?!
наши бабуины кирпичем и стальным ломом прекрасно справляются
I don’t even know why this was in my suggestions, I have no idea what is happening in this video.
Интересно а комментарии на английском такие же как на русском?
Really think that bs 5 dollar strap going to fix high low..
I use a pin bar. Way faster