Ok so here's the story about putting it back together the camera died and I didn't know it so you'll not be getting that video you'll be getting the Chrono test and accuracy with the hammer spring adjustment
This video is awesome. I have been looking for this a year now. Thank you. I did almost 2 turns. Went from 5 mags to 4 mags per fill. Reassembly was very easy. Im shooting .177 calibre. With HN Baracuda Hunter 10.49gr i was getting 18ftlbs. When i test again i will post the improvement
get yourself a few Euro /Dollar rubber doormat, the ones with the "mudholes", you can park your screws and parts in them, and it prevents scratching everything!!
Hey Roy, can do me a favor? Could you measure the gap where the magazine fits? I would like to know what is the longest pellet that can be single loaded
Hello my friend, what was the purpose of disassembling the weapon to give it more power? I have had the same one for a month and I would like to know if this way the invader is given more power, thank you and greetings from Spain.
Should have a video on the power level after i did this and before because i can't remember the results that far back but it got more power but you lose shot count cause of more air use
@@airpower7692 Thank you very much friend for answering so quickly, I don't mind losing a few shots, what I want is to get a little more power, I will wait for the warranty to pass to modify it, from today I subscribe to your channel because it is very interesting and you are the only one that explains how to dismantle the hatsan invader on the entire network, greetings from Spain.
Sounds like a bad old ring around the cup in front of the barrel or the cup is not in the proper position or you have a bad magazine try to let it cycle without a magazine
You don't have to take it all the way apart just take the stock off then loosen that set screw on the hammer and then turn the adjustment screw in the back counter clockwise and tighten your set screw back. I took mine that far cause I couldn't break set screw loose
Could be a number of things like the switch i describe in another video that's behind the trigger or it could be in the trigger assembly itself i really couldn't tell you I'd have it in my hands working on it
Ok so here's the story about putting it back together the camera died and I didn't know it so you'll not be getting that video you'll be getting the Chrono test and accuracy with the hammer spring adjustment
This video is awesome. I have been looking for this a year now. Thank you. I did almost 2 turns. Went from 5 mags to 4 mags per fill. Reassembly was very easy. Im shooting .177 calibre. With HN Baracuda Hunter 10.49gr i was getting 18ftlbs. When i test again i will post the improvement
Cool thanks. Let me know how it goes
You and I both need a decent rifle stand/work bench.
Great video.
I finally just got a folding table it works great
Thanks to that video more people will fill comfy to buy the in invader knowing how to disassembly and and do lubrication
get yourself a few Euro /Dollar rubber doormat, the ones with the "mudholes", you can park your screws and parts in them, and it prevents scratching everything!!
I want to be sure we can remove airtube with air? Then replace another one sith air too?
I can't remember i don't have the gun anymore to go check
Hello, do you know how to remove the barrel? I've got it blocked.
@@thecryingdutchman8922 sorry I never did that and I do not have this rifle anymore so I couldn't go through it to find out for you
The first one to make a video on it good job. Are you going to cut the stock like you did with the blitz or leave it as it is?🤔
Leave this one like it is
Chronograph tomorrow
How is you hatsan invader now? Would you still recommend the hatsan invader? Im planning to buy a semi auto pcp rifle. Or other suggestions? Thanks
I only had it a week and sold it but the guy i sold it to likes it and it still doing good
Hey Roy, can do me a favor? Could you measure the gap where the magazine fits? I would like to know what is the longest pellet that can be single loaded
15mm good luck getting your fingers in there
Hello my friend, what was the purpose of disassembling the weapon to give it more power? I have had the same one for a month and I would like to know if this way the invader is given more power, thank you and greetings from Spain.
Should have a video on the power level after i did this and before because i can't remember the results that far back but it got more power but you lose shot count cause of more air use
ruclips.net/video/IZAKB--1oIc/видео.htmlsi=VtxIRMA7ELK_t2nl
@@airpower7692 Thank you very much friend for answering so quickly, I don't mind losing a few shots, what I want is to get a little more power, I will wait for the warranty to pass to modify it, from today I subscribe to your channel because it is very interesting and you are the only one that explains how to dismantle the hatsan invader on the entire network, greetings from Spain.
@@airpower7692 Thank you very much
@@EDETAN75 your welcome. I do this to just about every air gun I've owned so far
Hello, can we loosen more than two turns? Thanks.
Yes maybe up to 4 but your shot count will drop way down to around 3 maybe 4 shots if lucky
I need you help. Sometimes the rifle does not cycle. The bolt fails to go all the way back to ready the next shot and i have to cock it manually
Sounds like a bad old ring around the cup in front of the barrel or the cup is not in the proper position or you have a bad magazine try to let it cycle without a magazine
That’s the only way to adjust the hammer spring, to take it apart?
You don't have to take it all the way apart just take the stock off then loosen that set screw on the hammer and then turn the adjustment screw in the back counter clockwise and tighten your set screw back. I took mine that far cause I couldn't break set screw loose
Hola mi problema es que el mio dejo de autogarce solo osea tiras el primer disparo y no se vuelve a cargar 😢 que podria ser el problema ?
😂 que pones mal los balines en el cargador
hello i would like a shooting rest/vice to support the gun ,to get the hands free. use some heat to get the locktite broken ,where possible
Already taken it apart
Yep! Put it back together to but the video camera died
Hola mi problema es que el mio dejo de autogarce solo osea tiras el primer disparo y no se vuelve a cargar 😢 que podria ser el problema ?
Could be a number of things like the switch i describe in another video that's behind the trigger or it could be in the trigger assembly itself i really couldn't tell you I'd have it in my hands working on it