Thanks mate it word just a you describe. I wash I'd listen probably the first time as I went on to watch other and it messed me up. Had to go back to yours to get the job done. Thanks Champ
Im about to fix mine also but when i pulled it apart (thanks to the string broke) i did not have the internal plastic ring and it was not bolted shut, everything went everywhere when i took it lose. Does it apply critical damage to the pulley if I dont get a new plastic ring and spring?
You will need all the parts or it won't work properly i don't know if you can buy the plastic ring and spring separately you might need another complete pull start.
+TheFuckingPresident T It sounds like your spring is broken or not attached. you will need to take it apart make sure the spring has a hook on both ends. if all looks ok follow my clip to put it back together. if not let me know what you find I might have some ideas to fix it.
+TheFuckingPresident T if you have taken the spring out you will need to tell me what part is broken is it one of the hooks on the ends or is it broken somewhere else
Have the same thing... did everything like U showed... but the Metalthing would not come out when I turn it... turned the plastic thing both possible ways.. no difference
is the pull start working properly like turning engine over when you pull it. if it is what I would do first is take spark plug out and put your finger over spark plug hole then pull cord if you don't feel pressure pushing your finger away from the hole then you might have internal issues like broken piston, broken rings, maybe even broken cam shaft if one of these is broken you might need another engine hope this helps
+Fix It thanks mate, i changed the pullstart it works now the bike starts however after 10minutes it shutsoff Also the petrol tap switch when turned on leaks alot of petrol through the pipe how will i fix this
sounds like your fuel bowl is over filling so your float is not shutting the gas off when bowl is full and engine is getting too much fuel. you will need to remove fuel bowl, remove float + float needle check in hole where needle goes too make sure its clean. give all parts a clean now you can bend float bracket a little down so it shuts off gas earlier make sure you put all parts back how they were when putting together then try it I have had this problem before on one of my bikes and this worked if it doesn't work you can try to bend float more but not too much or try to find another carby to put on it hope this helps
it sounds like your coil spring is not in properly or broken it must be hooked on both ends take it apart check nothing is broken and follow this clip to put it back together
Fix It ok thanks but I am working on a 125 cc dirtbike and a 500cc snowmobile And it is going really good I got my dad's snowmobile running good and mine so thanks a lot man keep up the good work
Thanks mate it word just a you describe. I wash I'd listen probably the first time as I went on to watch other and it messed me up. Had to go back to yours to get the job done. Thanks Champ
Rewinding the spring is some voodoo magic type shit
cheers pal you just showed me tha way forward lol fixed my sons bike thanks
Can you add how to put it back on the bike i cant get mine to fit tightly back on it it goes on the bike but doesn't phll the fly wheel
Thank you so much!!!. Just savede me 20 bucks
Mate, i wish i found your video earlier, but thankyou for the easiest tutorial ive watched. I have two now i can go fix.
Im about to fix mine also but when i pulled it apart (thanks to the string broke) i did not have the internal plastic ring and it was not bolted shut, everything went everywhere when i took it lose. Does it apply critical damage to the pulley if I dont get a new plastic ring and spring?
You will need all the parts or it won't work properly i don't know if you can buy the plastic ring and spring separately you might need another complete pull start.
Thanks for showing us we fixed the bike
Which way does the plastic bit in the middle go, arrows facing up or down?
hi i got no cord. which thickness and how long and where
i took mine apart and didn’t know that long thing was in there and it sprung out and got my eye
Thanks you helped me out so much
My center piece doesn’t come out
Mine don’t latch on
Hey I got a question what if the the in the middle doesn't go back after pulling the rope
+TheFuckingPresident T It sounds like your spring is broken or not attached. you will need to take it apart make sure the spring has a hook on both ends. if all looks ok follow my clip to put it back together. if not let me know what you find I might have some ideas to fix it.
+Fix It how do you fix the recoil spring
+TheFuckingPresident T if you have taken the spring out you will need to tell me what part is broken is it one of the hooks on the ends or is it broken somewhere else
+Fix It nothing is broken the rope goes back but not all the way
+TheFuckingPresident T ok I will make a video now on how I fix this and upload it for you
Have the same thing... did everything like U showed... but the Metalthing would not come out when I turn it... turned the plastic thing both possible ways.. no difference
If you have done everything the same there might be something broken or worn or missing check all parts are in good condition and are the right parts
cheers mate just help me out big time
hi when i pull my pullstart it is super light and the bike dont start it was not like this before what is wrong with it?
is the pull start working properly like turning engine over when you pull it. if it is what I would do first is take spark plug out and put your finger over spark plug hole then pull cord if you don't feel pressure pushing your finger away from the hole then you might have internal issues like broken piston, broken rings, maybe even broken cam shaft if one of these is broken you might need another engine hope this helps
+Fix It
thanks mate, i changed the pullstart it works now the bike starts however after 10minutes it shutsoff
Also the petrol tap switch when turned on leaks alot of petrol through the pipe how will i fix this
sounds like your fuel bowl is over filling so your float is not shutting the gas off when bowl is full and engine is getting too much fuel. you will need to remove fuel bowl, remove float + float needle check in hole where needle goes too make sure its clean. give all parts a clean now you can bend float bracket a little down so it shuts off gas earlier make sure you put all parts back how they were when putting together then try it I have had this problem before on one of my bikes and this worked if it doesn't work you can try to bend float more but not too much or try to find another carby to put on it hope this helps
Jaja jak berety chcialem szybko ha sam. Z Siebie się śmieje filmik ok tylko właściciel pupa czyli ja pozdro oby tak dalej 🤣🤣🤣🤣🤣🤣
I need some help on myn
Lucas Teixeira what's it doing or not doing
I put the wire in but every time I pull it it doesn't pull back in
it sounds like your coil spring is not in properly or broken it must be hooked on both ends take it apart check nothing is broken and follow this clip to put it back together
Thank you so much
Yo thanks I did it in 30 minutes so make more videos
+Alessandro Terzo If your stuck on anything on these bikes let me know
Fix It ok thanks but I am working on a 125 cc dirtbike and a 500cc snowmobile And it is going really good I got my dad's snowmobile running good and mine so thanks a lot man keep up the good work
Cool mate, cheers from Aus
Quando si rompe conviene comprarla nuova e piu sicura
Depends on what part is broken.
Awesome
wonder what he's doing today
I'm turning a old guys mobility scooter into a mini Ford roadster.
Thanks alot - helped heaps
Safe
Hey I got a question what if the the in the middle doesn't go back after pulling the rope