from the formula of operating frequency of the microstrip patch antenna. frequency is determined by the relative permittivity of dielectric and length of patch
@@dr.hariprasadnaikbhattu Someone said "The ideal value for the size of the radiation box is calculated as λ/4.". However, I could not fully understand. How is it calculated using this?
sir this video is very helpful thank you. sir may I know can we fabricate patch antenna on different substrates? bcz somebody told me tht substrates are very costly(other than FR4) and unavailable in India. If you have any idea let me know even fabricators address
hello dr, i hope you're doing well , thank you so much for the video , i've a question one about this video and one about a problem that i faced , first question , how to optimize the frequency in same case as in this video ? 2nd question ,i designed an antenna and i find that the input impedence is more than 50 ohm , it's about 160 ohm how can i optimize it too ? And thank you so much
Hello Sir! I was wondering in 9:34 of this video how did you go about determining how much of the patch you had to cut out? was there a technique/formula to this or did you just assume the amount to cut. Similarly, did you assume the length and width of the feed you attached, or is there an equation to determining this. Thank you!
Hello sir. Thank you for this helpful video. Can you inform about the polarization of this antenna and is it possible to use it in any kind of 4G communication systems?
Thanks for the video sir, is it possible to change the material of the patch? As in instead of assigning it a boundary of Perfect E , we can assign some other material instead?
Dear Dr. HariPrasad, Do you know plz how to redefine the dimensions of volume obtained by a sweep of a surface over a line path like we can redefine the starting points and the dimensions of a box after creating it? Best Regards,
Thankyou so much sir for this informative video. Kindly suggest me Which software is suitable for simulating antenna and Rectifier in one single software for rectenna design? Please recommend.
@@dr.hariprasadnaikbhattu sir thanks for the reply, my friend perchaged the HFSS software for his lab in engineering college for students, can we use that for making tutorial video like your video
Finally minute result--- create far field report---- rectangular plot option is pressed, so open a window there is no "sweep" option, the laptop is windows 11, so last graph is not available, what is the reason?
@@dr.hariprasadnaikbhattu sir after selecting the rectangle and the assigning port my menu is different than the video it just assign port name nothing else
Sir, i dont see the lumped port option for Assigning Excitation to the port. Is it because i am using a different version HFSS (Ansys Twin Builder Student 2023 R2)? please halp/
@@kalyannelli5834 patch has edge impedance of z=240 ohms. So use the inset feed to balance the impedance to z=50 ohms. So started the feed in x direction.
@@dr.hariprasadnaikbhattu Sir, after assigning to the lumped port I'm not getting the box like you got which is 50 ohms and the new line option also I'm not getting it
Excuse me sir Please provide a video on this design Reconfigurable Structure Reutilization Low-SAR MIMO Antenna for 4G/5G Full-Screen Metal-Frame Smartphone Operation
very helpful made this as my mini project your video saved us
😍🥰🥰🥰🥰😍😍🤩😘😘😍🥰🥰
Thank You Dr, This tutorial has been of great help
Thanks very much 😀
You are good professor. The lecture you uploaded helped me to design array antenna. Thanks for sharing good lecture.
Thanks for the Support
Very good Dr. Bhattu
Thanks 🙏
nice explanation....
Thanks
very good expalnation sir
Appreciate for the response
Video very helpful. Can you put a video for Ferrite Phase Shifter design simulation and S-Parameters. Thank You.
Hi, I not in antenna now a days.
hello sir. it's really helpful video! i wonder how did you get the feeding length (30mm)?
from the formula of operating frequency of the microstrip patch antenna. frequency is determined by the relative permittivity of dielectric and length of patch
Hello sir. First of all, your video is very helpful and good. Please can you explain us how did you calculate the radiation box dimensions?
Thanks for the response. I have used the radiation box dimensions as double the dimensions of x,y and z. This is to allow enough space for radiation
@@dr.hariprasadnaikbhattu Thank you for answering. So how did you calculate the x, y, and z dimensions?
@@nazl227 substrate is rectangular/square of x=40mm by y=40mm and z=1.6mm.
@@dr.hariprasadnaikbhattu Someone said "The ideal value for the size of the radiation box is calculated as λ/4.". However, I could not fully understand. How is it calculated using this?
@@nazl227 radiation box is a medium for radiation
So nice this videos
Thanks
Thank you very much sir, may I ask how you optimize the Freq at 2.4 GHz.
Use this video for optimization
ruclips.net/video/hKedMMA9tro/видео.html
@@dr.hariprasadnaikbhattu Thank you very much, Dr.
sir this video is very helpful thank you. sir may I know can we fabricate patch antenna on different substrates? bcz somebody told me tht substrates are very costly(other than FR4) and unavailable in India. If you have any idea let me know even fabricators address
Yes, There are other substrates which are costly. In India also there are fabrications but limited.
hello dr, i hope you're doing well , thank you so much for the video , i've a question one about this video and one about a problem that i faced ,
first question , how to optimize the frequency in same case as in this video ?
2nd question ,i designed an antenna and i find that the input impedence is more than 50 ohm , it's about 160 ohm
how can i optimize it too ?
And thank you so much
These may be helpful
ruclips.net/video/hKedMMA9tro/видео.html
ruclips.net/video/iKXujuS7OfI/видео.html
Hello Sir!
I was wondering in 9:34 of this video how did you go about determining how much of the patch you had to cut out? was there a technique/formula to this or did you just assume the amount to cut. Similarly, did you assume the length and width of the feed you attached, or is there an equation to determining this.
Thank you!
Hi, if you find away to calculate this parameter, can you share it here? I'm facing the same problem in my project!
@@matheuscardozo1865 Sure! same for you
Hi! I'm wondering this exact same thing as well!
Hi, I was told about this in a online workshop.
Can you share the approach as I have same issue
Hello sir. Thank you for this helpful video. Can you inform about the polarization of this antenna and is it possible to use it in any kind of 4G communication systems?
Hi Thanks for your response.
I don't know about polarization in antenna.
Thanks for the video sir, is it possible to change the material of the patch? As in instead of assigning it a boundary of Perfect E , we can assign some other material instead?
Yes, you can
@@dr.hariprasadnaikbhattu how
Dear Dr. HariPrasad,
Do you know plz how to redefine the dimensions of volume obtained by a sweep of a surface over a line path like we can redefine the starting points and the dimensions of a box after creating it?
Best Regards,
Hi, don't know about it.
Hi, do you have any video of circular loop for CP polarization technique?
No I don't have video on that
sir at 10.17 how did you subtract cut from patch like how how did you select those two together for substraction
Hi, first select one structure then press cntrl or shift key on keyboard to select another
How do you optimize antenna to get S11 at 2.4GHz? What i have to change?
Hi
Set the width of antenna as variable. Perform parametric analysis
Thankyou so much sir for this informative video. Kindly suggest me Which software is suitable for simulating antenna and Rectifier in one single software for rectenna design? Please recommend.
Thanks for the response. Antenna can be taken as source. Apply to the rectifier circuit. Use Advanced Design System tool.
Good explanation
Thanks
@@dr.hariprasadnaikbhattu sir thanks for the reply, my friend perchaged the HFSS software for his lab in engineering college for students, can we use that for making tutorial video like your video
@@microstripantennas-dr.hala1418 yes.
@@dr.hariprasadnaikbhattu thank you sir
@@dr.hariprasadnaikbhattu any upcoming tutorial video on mpa sir
Hii
Is this design can also be used for mm wave filtering antenna..
Please can anyone tell..
Yes
How did you come up with the dimensions of cut (9.5mm and 2.5mm)?
Hi, I did it in a FDP. I dont know much about that. Now I am not in Antennas
sir can u tell the feed width if i take the substrate as isola-speedISCR of dielectric constant 3.3
Hi, feed width remains same even if dielectric is changed
Sir, what if i want to design some other designs like star,ovel,some alphabets on substrate how can i calculate the velues
Use this link
www.emtalk.com/mpacalc.php
Based on the obtained length and width design a patch
Thank you sir
Weldon
Thanks
good explanation sir. but how-to decide the dimensions of rectangle to be cut?
I have taken from a video tutorial
sir what to provide as Zo and electrical length since they are 2 new fields in the calculator
Hi, I could not get your point
Sir how to select the cut and patch at the same time
Hi, if possible go through the video again. At video tiome 10.05 onwards
Use ctrl and select cut and patch
Hi sir , how did u calculated the xsize and ysize to cut
Hi, I did it based on tutorial I have attended
Finally minute result--- create far field report---- rectangular plot option is pressed, so open a window there is no "sweep" option, the laptop is windows 11, so last graph is not available, what is the reason?
Redo
Thanks
Redo the simulation process
Sir, How do you know that cut direction in x axis is -9.5? Please explain
It is a rectangular patch. Decide based on that
sir can u upload the video regarding designed and simulation of dual band mimo antenna for 5g application using hfss
Sir right now I am not working on Antennas
Hi can you plz help me in providing port excitation. Am not able to create line and the following steps.
Hi, once port is created. Assign lumped port. You see a small triangle shape then draw the direction
@@dr.hariprasadnaikbhattu sir after selecting the rectangle and the assigning port my menu is different than the video it just assign port name nothing else
After that if i go to excitation i get no option to create line
Sir, i dont see the lumped port option for Assigning Excitation to the port. Is it because i am using a different version HFSS (Ansys Twin Builder Student 2023 R2)? please halp/
It may be the reason
can we do this in student version?
currently im also having the same as urs
Sir, I would you to have (1.6,0.8,3.2 ) as a standard value, Is there any data sheet for that?
Hi, as per my study and research industrially also 0.8, 1.6 , 3.2 thickness substrates are used widlt
Sir I have excel data for co & cross polarization of E plane & H plane but I am unable to plot it in origin can you please help me.
Don't know exactly about it.
Sir when you cutting the feedline to provide the proper impedance matching to the patch, then how you get the calculation values
Sir plz tell us how the cutting values are came
@@kalyannelli5834 patch has edge impedance of z=240 ohms. So use the inset feed to balance the impedance to z=50 ohms. So started the feed in x direction.
@@dr.hariprasadnaikbhattu Yes sir! but how the X and Y size values are taken in tutorial you had taken X=14.7 and Y = -2.5
@@dr.hariprasadnaikbhattu sir PLZZ tell me how you taken the cutting values of Xand Y.
@@kalyannelli5834 you can get formula from google
For using HFSS for such tutorial sir any copyright issues
It is a commercial tool.
hello sir i want to know if we can simulate a microstrip multi-patch antenna
Not right now.
@@dr.hariprasadnaikbhattu please sir explain us and do a tutorial about it
Sir iam getting 3d model red mark in validation check
That's means you have not designed properly or missed any of the steps
How to calculate x size of the feed and x size y size of cut and postions of cut?
Patch has edge impedance of 240 ohm. So use a deep cut for impedance matching from the origin
sir can you pls share the mechanism of how to design a terahertz anteena in hfss
Hi, I don't know much about it.
Sir for rogers RO4003 what is the length and width of feed and port could you please give the values sir
Hi, no separate values it totally depends on epsilon during design. See at the start of designing
Hello Sir . I want to simulate conformal antenna. Can you help?
I am not working on antenna.
can we increase or decrease the gain of antenna?
Yes, by adjusting the length and width or through optimisation
Sir
How did you select patch and cut at a time?
Patch width and length is calculated at the starting.
Control+patch and cut
sir at what frequency it is designed....?
It is designed at 10 GHz frequency
Hello sir, can you please help me to design an patch antenna at 300GHz
Hi right now I am not working on antennas
How to create the lumped port part even after changing the XZ it is drawing as a rectangle not as an arrow
Sir please tell
Select the port
Right click
Assign
Lumped port
@@dr.hariprasadnaikbhattu Sir, after assigning to the lumped port I'm not getting the box like you got which is 50 ohms and the new line option also I'm not getting it
@@AnushaYadav01 Im getting this same thing too. It does not proceed to the arrow cursor
Same here, could anyone reply here if they get the solution to this?
Hello sir how to select patch and cut at a time to subtract?
Select both the cut and patch and perform the boolean operation. Like Unite, Subtract...
Use ctrl + A and select patch and cut
Excuse me sir Please provide a video on this design Reconfigurable Structure Reutilization Low-SAR
MIMO Antenna for 4G/5G Full-Screen
Metal-Frame Smartphone Operation
Hi, not working on Antennas
Sir how to select patch and cut for subtraction please help
Patch width and length is calculated at the starting.
I am not able to see option to add lumped modes on the excitation port. please help @
I'm having the same issue. It isn't letting me choose the impedance value in the 2023 version
I don't know about 2023 version
Sir, from where can I get this software. Please help
It is a Commercial tool not a free tool.
sir how to reslove the problem when the boundaries and excitations are invalid
Hi, Not much information about this question.
Tq sir
Thanks 👍
Sir,how Can i save images directly in software or take screenshots
@@reddylakshmisunitha4951 use save or export image option
@@dr.hariprasadnaikbhattu ok sir tq so much sir
@@dr.hariprasadnaikbhattu sir how to stop simulation before analysing the s-prarameter plot
What about electrical length?
It is designed with quater wavelength
hello please can you explain us how did you calculate the cut parameter?
Depends on the feed length impedance. Z decreases as we go deep.
Sir make video on fss in Mimo antenna
Hi, I may try but not sure
for me s parameter is not listed in the reports section
I could not get your point
sir it is not able to select the CUT and PATCH simultaneously.....how to select both simultaneously
Hi, it is possible
Select Patch first then use shift/ control key and select Cut.
@@dr.hariprasadnaikbhattu yeah sir got it...tqsm😻
Hello, nice video I was wondering where I could find the file?
Hi, I have designed the antema.
Could you please mail me the file?
Dear Dr.HariPrasad
Would you send me or share the link of this paper?
Thank you,
Hi, It is not from paper. I learnt the design through a workshop.
Sir how did you calculate the length of cut and feed line
Hi feed line is from (0,0).
Not much info about cut. Becoz i learnt from a online course.
@@dr.hariprasadnaikbhattu thanks l found out it.
@@yavuzciftci7989 can u tell me how please
Sir, Please tell how to learn HFSS design from basics .
HI sai, it is a basic patch antenna design in hfss.
@@dr.hariprasadnaikbhattu Ok sir , Please tell how to learn HFSS.. any Sources.?
Hlo sir you have document for this project,if you have send me sir
Hi, I dont have that project file.
can you please design micostrip patch antenna at 16.5ghz
Hi, I am not working on antenna now
How to calculate the dimensions of the ground
Hi, it need to be decided what length and breadth of antenna to design
Bhattu sir where are you from
Hi I am from Telangana
Sir, is HFSS working on android 11 version tablet ,.
Hi It works on PC not on Android
18:12
At that time simulation is performed.
Sir ,how to design 2*2 patch antenna array
ruclips.net/video/7DT7doBb2kk/видео.html
Which version hfss software sir
It is 2019 version
im not getting peak at 0
instead im getting heartin shape 😂 😂
what might be the problem
Hi, check the excitation port
How do we calculate the X size of cut rectangle??
It actually depends on feed line impedance
For the cut, how to know the width of the cut?
Hi, I did it in a FDP. I dont know much about that
@@dr.hariprasadnaikbhattu What is FDP?
Hai sir can u tell abstract of these
freq=2.4GHz, Er=4.4, H=1.6mm,
W=38mm, L=29.4mm
Sir I need your help
Hi. In what way I can help.
Ye kon sa software hai sir ???
Hi, this is antenna design software HFSS
My lumped port is not working properly reference conductor for terminal
Actually change the access to XZ
@@dr.hariprasadnaikbhattu ok thanks
@@akashsharma2602 same problem can you help me?
@@shivi6636 just go to hfss then click solution type then select terminal option and click ok good luck for your project
@@akashsharma2602 thank you but in my case it worked for modal option.
Sir mera gain negative aa rha
May be feed not connected properly
How can I contact you ?
What's the need
@@dr.hariprasadnaikbhattu design antenna by HFSS 13
@@mohammedsalem6085 I am not working on antenna now
H h
Evuuu
What is that
Sir jee dabba bhaag raha hai
Sir, I have problem in bending of antenna. Can you please give me your email id ?
I could not get your point.
@@dr.hariprasadnaikbhattu Sir I want to do bending analysis of antenna how to do it I need your help
@@beaughosh1739 I really don't know about it.
@@dr.hariprasadnaikbhattu ok sir.thank you.
Please write your email
hello sir i'm not able to add lumped port while clicking on excitation lumped port it's give reference conducter for terminals....please help me out
Hi, to add the lumped port change the grid to YZ plane. Use lumped port
Sir l I'm not able to do it...its Still ask for Reference Conductor for terminal while i click on Lumped port
@@daryenplays4148 hi, try to follow the video once again.
sir how can we design microstrip patch antenna for 5g communication
Hi, antenna design depends on the frequency. Based on frequency decide whether it is for 5g or other
@@dr.hariprasadnaikbhattu sir it frequency is 28Ghz
@@dr.hariprasadnaikbhattu how to find the dimensions of antenna