Here's an easy way to locate and fix a leaking injector. ENJ Customs on TikTok: www.tiktok.com... #injector #mercedes #CDI #Bosch #easyfix #diesel #fuelinjector
First off, do NOT use water. If the injector seals (plastic rings around injector) are not tight, the water will get into the engine and start rusting. If you have to check it, use a thin oil.
My 250 cdi had injector issues. Then I filled the tank with Total Fina diesel. They sell only one high grade diesel mix. My car immediately ran smoother and quieter and no more surprise injector problems. Now I only use Total Fina And the car loves it. Now, at 225k km, its time to pull, clean, and re-seat all four. The injectors are fine. Just micro-leaks at the copper seal. I'm going to let mercedes do the work for the warranty and they are really good and thorough.
Had a similar problem on the same engine (W203-CDI) only to find my injector cracked. after fixing the injector, the injector holder bolt damaged the threads and can't hold the injector. any suggestions please help
Water testing, interest idea I'll check that way too. I replaced the fuel lines and smell went away, cleaned up the whole area but after a short drive found diesel fuel on top of one injector. Also today saw a drop come off the front of the fuel pump which is a bigger concern TDI ALH
Actually what he should have done before even removing injector. You take to a car wash and pressure wash top of engine, buy a can of engine cleaner spray on top of head, let it soak for 5-7 min. Then rense with high pressure washer. I owen a MB 300SD 1983 turbo diesel. I perform all my maintence. His method of locating leaking copper ring, is fine, I use a spray can of carburator cleaner.
Hi and thanks for the comment! There is such a high pressure in the cylinder, dozens of bars, that water cannot flow into the cylinder. A leaking injector only causes those air bubbles. Of course, you should always dry off the water with a rag before starting to disassemble the parts. And always remember to clean the injector hole properly. But overall using water does not cause any problems.
Get the engine hot first. Loosen the bolt by a few turns, but leave it in. The injector might loosen itself as you drive around. There is a slide hammer that you can get as well. Mine came out with malgrips and a wiggle.
Hi and thanks for your comment. The only parts that were replaced were the copper ring that goes to the bottom of the injector hole and the bolt which I was removing in 2:34. I used that same old bolt to clean the injector hole by cutting a slot on it and screwing it in and out in the hole. This collects the dirt from the hole into the slot. In this situation the only parts that need to be replaced every time are the copper ring and the bolt. I mentioned about replacing them in 4:26. Hope this helps!
First off, do NOT use water. If the injector seals (plastic rings around injector) are not tight, the water will get into the engine and start rusting. If you have to check it, use a thin oil.
My 250 cdi had injector issues. Then I filled the tank with Total Fina diesel. They sell only one high grade diesel mix. My car immediately ran smoother and quieter and no more surprise injector problems. Now I only use Total Fina And the car loves it. Now, at 225k km, its time to pull, clean, and re-seat all four. The injectors are fine. Just micro-leaks at the copper seal. I'm going to let mercedes do the work for the warranty and they are really good and thorough.
Top job mate like the way you put the grooves in the old bolt and dowel stick for cleaning
Had a similar problem on the same engine (W203-CDI) only to find my injector cracked. after fixing the injector, the injector holder bolt damaged the threads and can't hold the injector. any suggestions please help
Water testing, interest idea I'll check that way too. I replaced the fuel lines and smell went away, cleaned up the whole area but after a short drive found diesel fuel on top of one injector. Also today saw a drop come off the front of the fuel pump which is a bigger concern TDI ALH
Mine still smells how did you get rid of the smell
Liked the video just hated the music but great job!!!
Thank you for the video and love the music !
Actually what he should have done before even removing injector. You take to a car wash and pressure wash top of engine, buy a can of engine cleaner spray on top of head, let it soak for 5-7 min. Then rense with high pressure washer. I owen a MB 300SD 1983 turbo diesel. I perform all my maintence. His method of locating leaking copper ring, is fine, I use a spray can of carburator cleaner.
Tried to watch but the overpowering music killed it. Cubit off!!!!
Best video ive seen, great job
car was running funny one day i smelt gas real bad and found it spraying just pushed it in with my hands and it went another 2 weeks lol
mine HDI injector spill lot of diesel fuel out even it have all seals !! was it because injector hole are not clean or?
If your having trouble phone a friend continuously
What do you mean ?
Do you need to bleed the fuel line once finished?
No need,since it's just one injector, the other injectors will still fire n the one which was removed will bleed itself as the engine runs
is that water not gonna leak into cylinder and cause problems ?
I wondered that
Hi and thanks for the comment! There is such a high pressure in the cylinder, dozens of bars, that water cannot flow into the cylinder. A leaking injector only causes those air bubbles. Of course, you should always dry off the water with a rag before starting to disassemble the parts. And always remember to clean the injector hole properly. But overall using water does not cause any problems.
Just use diesel for that test or WD40
@@lusa3002 diesel. Good way to blow up mate😂
I can see sum people becoming stuck with this ,with air locks
How does this problem present in symptoms in a modern diesel. Will it affect data across modules?
My injector is stuck i cannot remove it any suggestions ?
Get the engine hot first. Loosen the bolt by a few turns, but leave it in. The injector might loosen itself as you drive around. There is a slide hammer that you can get as well. Mine came out with malgrips and a wiggle.
@@martynm.449 thank you very much
Cool! I"ll do the same.
you need to talk to tell me what you are doing
Nice but it short cut, you did not show which part did u replace and how to do it.
Hi and thanks for your comment. The only parts that were replaced were the copper ring that goes to the bottom of the injector hole and the bolt which I was removing in 2:34. I used that same old bolt to clean the injector hole by cutting a slot on it and screwing it in and out in the hole. This collects the dirt from the hole into the slot. In this situation the only parts that need to be replaced every time are the copper ring and the bolt. I mentioned about replacing them in 4:26. Hope this helps!
Cool
How to fix leaking celinyador
Hi
💯👍👍
Yeah, let's use a piece of wood to clean down inside the whole. Don't worry if it breaks 😂😂😂
wood that thick isnt breaking doing this
po.p
Sir number send karo