Really enjoyed your review. Felt very genuine coming from a regular user who loves 3D printing. Appreciated your additional comment overlays when “Future Kiara” learned more (e.g. trying different filament). Loved the closeups while printing. Keep up the great work!
I have the Artillery Sidewinder and the build plate is just a little short for a extra large cosplay helmet so I bought the SV03 for that extra 50mm. I was having a problem leveling the bed then I came across your channel!! Thanks a million!!
I noticed your runout sensor mounted backwards. And ditch the clips. I use masking tape for the bed. Just make sure to leave extra bed on left side for the setup line (initial line that gets put down). I 100% agree. I love this printer. My only two complaints are the Extruder cable gets dragged across printed if you don’t suspend it somehow and the instructions are a hot mess.
you can get rid of that auto filament reject at the start of your prints by looking into the start gcode under the printer settings in your slicer. if not, check in with the seller for a firmware update. 0.6mm should be standard
This video was definitely a life saver with my SV03! You explained things MUCH better than other videos I’ve seen! Question for you or anyone else that might know. When I do big prints (such as helmets/masks) I run into this issue where the nozzle hits the supports often when moving around. It hasn’t affected the prints yet but it’s annoying and stressful to hear cause I’m expecting it to snap the supports and ruin the print. Usually lasts until it finishes the supports and continues to the actual model. Is it something with the Z Offset? I’ve tried to perfect it but always ends up happening.
Do yourself a favor and on the gantry where the direct drive is the whip of wires is getting pinch when it moves all the way to the left between the frame, pull the wires out of the way and just let them hang otherwise you may have wires damaged from that. I just put mine together last night and noticed that and figured I'd see if anyone else was setup that way
do you have any recommendations for abs settings on this i cant for the life of me figure out what im doing wrong with this hatch box filament on this printer also did you have the problem where the filament would just flow before the print would start
It seems like instructions are a problem in a lot of the lower-cost printers. The small investment in writing a decent manual would probably pay off in higher customer approval/loyalty.
Really enjoyed your review. Felt very genuine coming from a regular user who loves 3D printing. Appreciated your additional comment overlays when “Future Kiara” learned more (e.g. trying different filament). Loved the closeups while printing. Keep up the great work!
I have the Artillery Sidewinder and the build plate is just a little short for a extra large cosplay helmet so I bought the SV03 for that extra 50mm. I was having a problem leveling the bed then I came across your channel!! Thanks a million!!
I got the Sv01 and loved it so much I got the sv02, Sovol makes some really good machines
Genius RUclipsrs are only few in the world you are extremely genius!
I don’t know a lot about 3D printers themselves but this was really interesting! Have a great new year!
thank you! hope you have a great new years as well!
I noticed your runout sensor mounted backwards. And ditch the clips. I use masking tape for the bed. Just make sure to leave extra bed on left side for the setup line (initial line that gets put down). I 100% agree. I love this printer. My only two complaints are the Extruder cable gets dragged across printed if you don’t suspend it somehow and the instructions are a hot mess.
Very helpful! Please do more.
you can get rid of that auto filament reject at the start of your prints by looking into the start gcode under the printer settings in your slicer. if not, check in with the seller for a firmware update. 0.6mm should be standard
You’re adorable. Thanks for the video. I just made my mind, this is going to be my next printer.
Nice upgrade!
This video was definitely a life saver with my SV03! You explained things MUCH better than other videos I’ve seen! Question for you or anyone else that might know. When I do big prints (such as helmets/masks) I run into this issue where the nozzle hits the supports often when moving around. It hasn’t affected the prints yet but it’s annoying and stressful to hear cause I’m expecting it to snap the supports and ruin the print. Usually lasts until it finishes the supports and continues to the actual model. Is it something with the Z Offset? I’ve tried to perfect it but always ends up happening.
you can try to turn z hop on in your slicer . it slows the print a bit down, but for tall supports it can save it
Nice! I don't even saw the video but I'm sure it is nice!
Execellent video very informative.
Do yourself a favor and on the gantry where the direct drive is the whip of wires is getting pinch when it moves all the way to the left between the frame, pull the wires out of the way and just let them hang otherwise you may have wires damaged from that. I just put mine together last night and noticed that and figured I'd see if anyone else was setup that way
Offer to rewrite their manual for them. They may pay you back with more printers.
OH! WOW
I know very little about 3D printing. This looks amazing and terrifying
It's one of the most addicting things out there...
Do you know where I can get a new extruder gear/wheel for the sv03? I can’t seem to find any on Amazon, or I just don’t know what to look for lol.
The beast !!?? Voron 2.4 !!!!!!!!!!!!!!!!!!!
it’s a beast compared to what i’ve used so far haha
do you have any recommendations for abs settings on this i cant for the life of me figure out what im doing wrong with this hatch box filament on this printer also did you have the problem where the filament would just flow before the print would start
Thank you
Awesome
It seems like instructions are a problem in a lot of the lower-cost printers. The small investment in writing a decent manual would probably pay off in higher customer approval/loyalty.
anybody know why when i do the z offset to level the center of the bed the extruder does not move but the dial says it going up and down
I just ordered a sv03 any tips or tricks ?
Can you create a new 3D objects and say how to 3D printing work
How do you store it and keep it form getting dusty?
yes mommy
hi char always lovely to see u in my comments
Which video did you watch with the guy who gave the instructions for the z offset?
the link should be in the description, he left a comment on it that explained what you needed to do
Did you ever figure out the filament change issue?
no unfortunately, just kinda learned to live with it
My like 201 ❤️
Un contenido muy bueno
i need mager help it wont let me tap INIT in initailize eprom it makes a weired noise and the restore failsafe does the same thing :( pls help me
that’s what it does. it beeps when you press it but it should still work
Thanks
@@KiarasWorkshop mine beeps but I have to press cancel to get out the screen like after I press init Epsom it stays on same screen
Hi I'm Sorr and you how old you