Great journey Harvey. Thanks so much for taking us along . That’s a deadly saw not for the faint of heart . The rewards will come , awesome content brother 🇦🇺✊🏻
Welcome back. Glad to see your back at it. Love watching you build these Frankenstein saws. Wow, a 365 special that is 90 ccs. But as problems arise you deal w/them. Good job & thank you.
Mr Horse, you are the kind of guy that I could hang with and soak up as much knowledge as I possibly can. Much love from North Carolina 🤙. Prayers for your health to keep getting better.
Well done on the build, not many will take on this and also succeed. Cast iron needs more tolerance around the piston and I know this from a danarm chainsaw 125 with cylinder lining made of cast iron that seemed loose on cold but it runs great with loads of power. Well done and onwards and upwards.
Going to be a bad man of a saw. Missed your videos and soo glad to see you back. I looked everywhere for information on what's happening with you and if things are good. Keep 'em coming.
I think you're about to get all the gremlins looking for a new place to make their home; I think, with the pin, increased interference-fit, ring gap and extra 0.001" piston clearance, you've inoculated for gremlins!! Gardening running a little late here too; hay is ahead of time, but garden slow going.
Just watchin the videos now Harvey good stuff period! It great to see you in the shop teachin school again! Have you have an opportunity to speak to the gentleman about my 394 and 371?
This is a really interesting build but I have 1 question, why are you using a winter air filter? At least that's what they're sold as where I live and every dealer carries 2 tpyes. The cloth tops are for winter to keep trap and moisture out of the carb, you carry one in your pocket and swap it when the one on your saw starts to freeze and let the other dry out in your pocket and the nylon ones are for summer and they come in both flat and high top.
You haven’t posted in a few weeks, so I will put my question here. Hope you are OK. Have you ever used a platinum tip or iridium plug in any of your saws? I ask because you’re a dirt bike guy, and I think some old time dirt bike guys used to use the now discontinued Champion platinum tip plugs. The ones with a number and then the letter G. Anyway, hope you are doing well. Thanks and take care.
Halo bos. Konten-konten nya sangat menarik.banyak belajar dari konten anda. Apa cylinder 365 bisa pake cilinder tipe lain. Untuk meningkatkan tenaganya.
So much good and interesting content. I have a question: Does it matter if you go up or down on the intake to get total duration? The piston doesn't interfere. Have a good weekend 😊
@theironhorse6600 Thanks for answering 👍 and I have a follow-up question: I see that you make notches on both sides of the roof of the intake. Do you measure timing from the roof between the notches or from the notches. The notches seem to be the highest point of the intake. Thanks
Pin it or machine a ledge on the cylinder and tack weld it so it can’t move … before ya even fire it! You’re very fortunate you don’t have a 90cc paperweight 😂
Harvy would you or your boy be interested in building a dirt bike enngine for me ? It's not for Me I'm built him one last year but the bottom let go ? I could build it again but I know you're engine's RRRRRIP .
What saw chain on a 100 ft roll do you recommend to buy and from who? I have been searching and get mixed reviews, i need 325,063. Any info or recommendation's would be appreciated.🇺🇸
Good seeing you Harvey. Thanks for bringing us along on the Iron horse learning experience.
Great journey Harvey. Thanks so much for taking us along . That’s a deadly saw not for the faint of heart . The rewards will come , awesome content brother 🇦🇺✊🏻
Welcome back. Glad to see your back at it. Love watching you build these Frankenstein saws. Wow, a 365 special that is 90 ccs. But as problems arise you deal w/them. Good job & thank you.
Nice skills Harv. Good that you tink outside the box. Now, if I could fit a 372 cylinder on a 55 that would be perfect. haha
Mr Horse, you are the kind of guy that I could hang with and soak up as much knowledge as I possibly can. Much love from North Carolina 🤙. Prayers for your health to keep getting better.
Harvey, I'm glad you are back. I've missed your videos.
Glad you’re back Harv
Yes sir you are back in the grove my friend. You may have had a failure but you have the skills to fix it no matter what the trouble is. 👍♥️
Always a great day when IronHorse shows up !! What am awesome fix Harvey, excellent job 👍
Interesting build. My main concern would be if the transfers flow enough air for the extra cylinder capacity
You Are a Good Man Harv, God Bless, and Take Care.
Glad to see you back Harv. Watching from Australia
Good save. Good thing you shut it down when you did.
Thanks for taking us along on the build Harvey, it's always great to be along for the ride!
Good to see you mate! Hope you anf the family are well! Keep up the great work!
Harvey great to have you back!
Well you call it 🐎 let's have a firewood cuttin splittin weekend!😊
Well done on the build, not many will take on this and also succeed. Cast iron needs more tolerance around the piston and I know this from a danarm chainsaw 125 with cylinder lining made of cast iron that seemed loose on cold but it runs great with loads of power. Well done and onwards and upwards.
We learn what to do as well as sometimes what not to do.. either way certainly enjoy the process. Thanks for sharing !
Hey Harv!
I'm excited to see this bad boy in the wood!
Thanks again for all your advice, I'll be hitting you up again soon.
Going to be a bad man of a saw. Missed your videos and soo glad to see you back. I looked everywhere for information on what's happening with you and if things are good. Keep 'em coming.
been enjoying this series! thank you uncle Harve! I have faith that it'll survive!
have a wonderful day/night people peace
Howdy, Harvey! Great to see you!
Sure is nice to hear your voice again! Thanks for your time an have a blessed holiday!
DONT BE SORRY BUDDY YOUR HEALTH COMES FIRST ,,YOU LOOK HEALTHIER STAY SAFE BUDDY
i like loctite 515 anerobic flange sealant. used on a sbc water pump with no gasket without any problem.
I think you're about to get all the gremlins looking for a new place to make their home; I think, with the pin, increased interference-fit, ring gap and extra 0.001" piston clearance, you've inoculated for gremlins!! Gardening running a little late here too; hay is ahead of time, but garden slow going.
Thank you for sharing the experiment. I didn't think about the sleeve dropping. I was wondering about it potentially turning.
Always be honest that's what we got and do the best with what we have.
Just watchin the videos now Harvey good stuff period! It great to see you in the shop teachin school again! Have you have an opportunity to speak to the gentleman about my 394 and 371?
great to see you Harvey. thanks for all the info and videos.
BLESSS YOU!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
This is why some saw makers use hard chrome plating on aluminum fined jug. Works better than a sleeve for sure I H.
What an awesome project, Harv! I love it. The saw is going to be a hit. Be good, my friend.
Good stuff. Have a great memorial weekend!
My favorite you tuber
Awesome job, thanks for sharing!
I use motoseal always does good sometimes you will get a tube that's runny and you gotta squeeze around 9n the tube to mix it up
Haven’t watched in a while you look good mister
Good job good save but it don't sound quiet right it don't pick up hope it better with use
awesome your feeling good
Awesome video Harvey
Can’t wait to see the super sleeper in the wood pile Mr Drake ❤👹👹💪🏿
I give you credit..no one else trys such insanity..i ve found sanity is overrated..I'm having fun following along for the ride🙃🙃😆😆
Hey Tim!
This is a really interesting build but I have 1 question, why are you using a winter air filter? At least that's what they're sold as where I live and every dealer carries 2 tpyes. The cloth tops are for winter to keep trap and moisture out of the carb, you carry one in your pocket and swap it when the one on your saw starts to freeze and let the other dry out in your pocket and the nylon ones are for summer and they come in both flat and high top.
You haven’t posted in a few weeks, so I will put my question here. Hope you are OK. Have you ever used a platinum tip or iridium plug in any of your saws? I ask because you’re a dirt bike guy, and I think some old time dirt bike guys used to use the now discontinued Champion platinum tip plugs. The ones with a number and then the letter G. Anyway, hope you are doing well. Thanks and take care.
😎👌
Greetings from Germany Peter
Husqvarna-Pit
😊
Hi Harvey two days in a row
Halo bos. Konten-konten nya sangat menarik.banyak belajar dari konten anda. Apa cylinder 365 bisa pake cilinder tipe lain. Untuk meningkatkan tenaganya.
Long time no see
Made a ironhourse pipe got to show you !!!
What do you think about a 372xp with 394 crank and cylinder modifying the case for larger bearings , I have a Machine shop in Connecticut
So much good and interesting content. I have a question: Does it matter if you go up or down on the intake to get total duration? The piston doesn't interfere.
Have a good weekend 😊
It has to be the floor of the intake!
@theironhorse6600 Thanks for answering 👍 and I have a follow-up question:
I see that you make notches on both sides of the roof of the intake. Do you measure timing from the roof between the notches or from the notches. The notches seem to be the highest point of the intake. Thanks
Pin it or machine a ledge on the cylinder and tack weld it so it can’t move … before ya even fire it! You’re very fortunate you don’t have a 90cc paperweight 😂
Also, I wonder if a roll pin would be better hold in heat differences?
I put a screw through the tank, brand new tank on 029 039...wrong screw
Harvy would you or your boy be interested in building a dirt bike enngine for me ? It's not for Me I'm built him one last year but the bottom let go ? I could build it again but I know you're engine's RRRRRIP .
What saw chain on a 100 ft roll do you recommend to buy and from who? I have been searching and get mixed reviews, i need 325,063. Any info or recommendation's would be appreciated.🇺🇸
I don't think drilling completely thru the cast was the way to go. Maybe partially would be better??
Couldn’t you just green loctite the sleeve into the cylinder ???
hey IRONHORSE how much to port and muffler mod a ms311??
G'day Harvey. I have a question do you no anyone that has a muffler for an 084? They seem to be very hard to find. Good to see your doing better👍
You will never find one. Have someone build you a pipe or something.
Could a MS880 muffler be made to fit?
@@roostergamer2664nope.
🇺🇸🗽👌
What did you do to remedy the compression problem?
Продолжайте свой проект, будет интересно чем закончится
I hope it ends well friend!
Nice job.. question. Can you weld a muffler on my gas bike engine? Keeps falling of bolts strip.. let me know I'm in the 607 hornell are ty sir
well
Sleeve is so thin probably the issue
Since when did chain saws blow up ? .