Godox AD-AB Set Adapter Hoder To Bowen Mount for AD300Pro ( AD300 Pro )
HTML-код
- Опубликовано: 7 сен 2024
- Godox AD-AB Set Adapter Hoder To Bowen Mount for AD300Pro ( AD300 Pro )
-อแดปเตอร์สำหรับแปลงใส่ซ๊อฟบ๊อกเมาท์ Bowen
-ใช้ได้กับแฟลช Godox AD300Pro
-ตัวเมาท์เป็นโลหะ
วัสดุ ABS พลาสติก ขนาดเบา พลาสติกทั่วไปจะมีลักษณะแข็ง แต่เปราะแตกหักง่ายหรือถ้ามีลักษณะแข็งเหนียวก็จะมีลักษณะอ่อนนิ่มไม่อยู่ทรง แต่พลาสติก abs แตกต่างจากพลาสติกทั่วไปเพราะเป็นพลาสติกที่มีความสมดุลทั้งในเรื่องความแข็งและความเหนียวสามารถคงสภาพรูปร่างได้ดีทำให้มีคุณสมบัติทนทานต่อแรงกระแทกได้ดีและยังทนต่อแรงเสียดสีความร้อนสารเคมีได้ดีกว่าพลาสติกธรรมดาทั่วไปมีช่วงอุณหภูมิที่สามารถใช้งานได้กว้างนั่นคือ -20 องศาเซลเซียสถึง 80 องศาเซลเซียส
How do you get them to release the flash tube cover? I can’t get mine to release it once the adapter is on.
Flashpoint really should link to your video!!!! Great job
Yep... much better than Godox's official video.
Really cause I was about to send this mess back!
Thx
will it work it Godox ML60?
thanks
Hellow friend, Did you find out if works with ml60?
The Bowens part works for both the AD300Pro and AD400Pro, correct? And uses the same screws? I have the Bowens adapter for the AD400Pro but need the AD-AB part for my AD300Pro
The bowen mount is the same ad400 pro adapter?
Yes I believe so
Is the modifier not going to slide off with the bowens mount off the head by the gravity ? I have this bowens mount on my ad400pro but it is attached this with screws this one I see you only slide in.
You must not have watched the whole video. There are 4 screws he puts in.
& how to mount this full setup on stand ? on a 2/3 screw thread LOL
Is it possible to remove the godox reflector easily while the release button is covered by the bowen adapter? Thank you for this video.
Hi, I'm just fitting this to my 300pro right now, and it looks like the release button on the adapter also releases the button to remove the protection cover too.
so .. it does, but it's pretty stiff at first.. its going to need a few goes to get it moving smoothly...
@@stephenfilby9147 thank you, thanks so much for confirming that
The lever on the ad400 adapter pushes a spring on the ad300 ring which in turn pushes the ad300 lever haha. I made a diy version that solves a LOT of ad300 / ad400 / ml30 / ml60 bowen's mount frustrations: ruclips.net/video/uR-fnIUYIyQ/видео.html