I just walked in a hobby shop yesterday, and dropped $850 on a brand new arrival 2.0 brand new batteries in a badass! And I love it just go buy things a beast that's all I can say it's awesome!!!!
Great video. Drooling over your setup. Don't hit your foot ! lol ! I like how stayed safe around the kids. These things get really dangerous at those speeds. Rock On!
i do speed runs with my ERBE and big ol trencher X's, i tied braided fish line around them and it keeps the ballooning under control but doesn't effect bashing, great video
Hey Ricky, hopefully this still finds you beating up your revo, I agree grab street tires, tighten up the rear suspension and then try it, lower that ride so it does not flip so easily even with the bars which drag it down in speed when it hits them it still performed awesomely great vid. Subbing because I am thinking seriously about getting the new one with the app built into the electronics.
Brett Boutan may sound dumb but this doesn't seem much bigger than my rustler but my rustler on 3s is wobbly and I hit 57 on 3s and it wobbles and 63 with slipper clutch setup is it just the weight of the car
Good video I like doing speed run, got my daughters rustler up to 49.4 mph on gps in a parking lot on 3 cell running a 86 tooth gear trying to get into the 60's mph range
Thats awesome, great speed run. I did a speed run with my e-revo and got busted by the COs on the May long weekend. Theres a vid on my channel, you got way more speed then I did (4S max). I picked up the pro-line street tires but I gotta pick up some 3S batts. And then speed ON :-) Great work, Cheers
Great video man very clean. Love what I have seen. I know you hear try this try that. But I own an E revo and found near a 28-30 to 32-33 ish S to pin has gained most top speed.Also might try dual batt in series for weight and balance ratio. Love this video wish more ppl pushed the limits :)
That wheel slop is because of the little pin set screws that hold your 17mm hex adapters on. i used green thread locker and really torked them down and problem solved. Another option would be to try a different style of hexes... really hope you can use my advise cheers bro.
Its not the set pins they are usually tight. What it is, is the actual hex against bearing u can pull them in and out depending on your slop and how bad 1 to 2 mm. Basically a shim or different hubs altogether like hpp would be better. If shimming u have to get one small enough in diameter to just ride the inner race of bearing .
Steve S ya it definitely with the different set ups. It was mostly due to the batteries more than the gearing. The 6s accelerated like a bat outta hell in both gearing set ups and the 4s was a bit more tame! Thanks Steve!
my custom setup has only a metal spur gear off the clutch gear to the drive shafts going to the front and rear .... it has almost no top speed the more you stay on the gas the faster it will go .
the higher see lipo just means that when you pull the trigger all the way you get more power instantly not necessarily more speed but the torque increases really crazy versa 35c vs. A.50 see when you nail it because you get a hundred c of current through a 50cc battery burst
Ricky Revo rc thanks! But I actually meant my full sized car lol working on customizing it. Adding Horse power, improving handling and visual appearance
Hi, I recoomend Truggy tires for speed runs. I use medium compounds ( hard ) and the car is still controlable. In my opinion street tires blow too much.
Hey Ricky. I have the same axial wheels with Trencher X's. Did you ever have an issue with the inner beadlock ring on the front cutting into the front lower A-arms? And if so, what did you do to fix it? Thank you.
Hey Ricky quick question about the spur gear on the Erevo. I run (2) 3s lipo in mine and I go through a spur gear about 2-3runs every time. Got the mesh set up right. Tried the paper trick, even tried moving the motor under easy acceleration so find that sweet spot where the gear mesh runs smooth. U ever had this problem before or got any tips thanks.
+Ricky Revo rc the teeth are wearing out. After a few runs u can see wear marks on them. I've tried backing the slipper 1/4 turn to 2 full turns results are the same. Nothing looks bent heard spin with no wobble.
Elite Status I love them they have superior Traction over a lot of tires........BUT your drive-train will not like them!! I have a new set of tires in route for my e revo I have done 3 rear diffs since these badass tires!
+Daniel Rc you should be ok with those upgrades! make sure your slipper is adjusted according to your driving style and try and stay on off road surfaces to minimize strain on your drive-line.
+Nathakrit Apithanangsiri Just ease into the throttle rather than just pulling the trigger. when I run 6s I just use the wheelie bar at the lowest setting @ 6:00 in the video!
Thanks bro I appreciate that!! The tires and rims I,m using are axial 40series bead-locs with big joes for tires. they're great for most terrain but i wouldn't recommend them for high speed street use lol!!
another quick question i see some videos where they have full throttle and the revo goes when i drive mine it sounds like its spinning the spur gear before it takes off so theres no tire spin at all or the truck does not flip
Ricky Revo RC yup u nailed it the screw was super loose I gave it 1 1/2 turns and now it drives perfect puts the power to the ground wheelies ect and thanks bro You the real MVP quick responses and all can't wait for more videos !!!
Get those belted monster truck road crusher tires on sweepracingusa.com they don't balloon at all and look nice you'll see how fast that erevo can go!!!
Ricky Dicky Doo I want to ask you a ? I would like to know.. What Pinion Gears I should Place on my E-Maxx Brushless to Get it to do Wheelies. I am Running Lipo3's x 2 for The Traxxas E-Maxx Brusless. Can you suggest something good for me? I like your Video. I 'm going to Subscribe to you. Currently I have a 1969 Dodge Charger on my E-maxx PAINTED To a TEE ! It is SICK Looking. I will try 2 post a Video for you to see my Truck. I have NO Videos on my U Tube cause I never knew how to do it. I am Waiting to take my Truck into hobbie Hole so they can do ALL the Tellementrys for me. I am a NEW-BIE 2 it. lol I hope to hear from you Ricky D
+Dr. J. K. Gallagher. you can just tighten up your slipper clutch to do wheelies but I wouldnt leave it tight for too long cuz your drive train will start taking a beating and thanks man!
Matt Gibbons I run 4s for general bashing and having fun! if I have a big open area to really open it up, I run 6s. check the website in the description for more info and a product review of the car
That was freakin awesome ricky I've been wanting to do speed run's on my 3 trucks my daughters has my gps any who lol I just wanna get videos of going fast but I don't know if my vehicles r set up good enough we will see hear pretty soon crash n burn always makes for good videos lol thanks for your cool video buddy I gave you a big shout out on my traxxas e revo tutorial and shout out vid I would be honored if you check it out thanks buddy you have kik ass videos👍👍👍👊
I watched and gave a big thumbs up Thanks so much Roy! just run that thing how it is my car was set up for bashing nothing special! try it out see how it goes!
Ricky Revo rc will do brother thanks a lot man we drive like we stole them lol makes for good videos brother I'll be checking out some more of your video soon you always have good vids man and thanks for checking out my video much appreciated brother👊👊👍
Michael Mack 3s at 55mph on stock vxl will burn out motor or esc. we're talking 2200kv motor that can run all day on 6s without getting hot. your slash does not have more power it's just over geared.
I just walked in a hobby shop yesterday, and dropped $850 on a brand new arrival 2.0 brand new batteries in a badass! And I love it just go buy things a beast that's all I can say it's awesome!!!!
Great video. Drooling over your setup. Don't hit your foot ! lol ! I like how stayed safe around the kids. These things get really dangerous at those speeds. Rock On!
David Thompson Thanks David! Yea you gotta watch whats going on around you with these things!
i do speed runs with my ERBE and big ol trencher X's, i tied braided fish line around them and it keeps the ballooning under control but doesn't effect bashing, great video
nocoolname32 Thanks bro!
Hey Ricky, hopefully this still finds you beating up your revo, I agree grab street tires, tighten up the rear suspension and then try it, lower that ride so it does not flip so easily even with the bars which drag it down in speed when it hits them it still performed awesomely great vid. Subbing because I am thinking seriously about getting the new one with the app built into the electronics.
that wheelie bar was funny. just spinning along all day. good video. thx for showing difference in spur gears.
thanks bro!
Brett Boutan may sound dumb but this doesn't seem much bigger than my rustler but my rustler on 3s is wobbly and I hit 57 on 3s and it wobbles and 63 with slipper clutch setup is it just the weight of the car
was thinking of buying the erevo
Thanks ricky revo for sharing.. the e revo sounds like a monster.
Good video I like doing speed run, got my daughters rustler up to 49.4 mph on gps in a parking lot on 3 cell running a 86 tooth gear trying to get into the 60's mph range
Big joes probably not the tires of choice for speed runs, but glad you gave us gearing I noticed your summit shafts as well.
Hargak Yea big joes are no good for this but I wanted to do the speed runs in normal basher form! Your welcome and thanks bro!
Those tires look sick. Nice speedruns too.👌👍
i want the e-revo especially the brushless, but i can't afford it its wayyy to expensive
Nice Speed Runs! Great Job on the different gear ratios and lipos! You deserve a double Thumbs Up!
thanks bro!
Thats awesome, great speed run. I did a speed run with my e-revo and got busted by the COs on the May long weekend. Theres a vid on my channel, you got way more speed then I did (4S max). I picked up the pro-line street tires but I gotta pick up some 3S batts. And then speed ON :-) Great work, Cheers
thanks man lemme know how those tires work for you!!
Scale Town that’s what I run on mine I nit 60mph in mine it was asoum
Nice video. Instead of taking out the long travel you can just 'zip-tie' them to limit travel that should work just as good. Cheers!
thats a good idea man thanks!!
Great video man very clean. Love what I have seen. I know you hear try this try that. But I own an E revo and found near a 28-30 to 32-33 ish S to pin has gained most top speed.Also might try dual batt in series for weight and balance ratio.
Love this video wish more ppl pushed the limits :)
Thanks for the tip bro! and thanks for comment man I really appreciate it!!
So. Im running 18/62 on big joes 6s 50c...i managed 52mph consistantly... try it out. Youre ballsier than me brotha lol
Nice I'm gonna try 19 40 now an then maybe 25 38 these things are hard to control at 50plus
That wheel slop is because of the little pin set screws that hold your 17mm hex adapters on. i used green thread locker and really torked them down and problem solved.
Another option would be to try a different style of hexes... really hope you can use my advise cheers bro.
thanks bro! I actually smoked every wheel bearing on the car in this video! I thought it was the pins too but they were tight! thanks for the tip bro!
Damn Behring's.. Try the rpm bearing set up. They are alot more durable. But that requires changing to rpm knuckles also.
Lol typo....... Berrings
lol will do man and thank you for the tips man I do appreciate them!
Its not the set pins they are usually tight. What it is, is the actual hex against bearing u can pull them in and out depending on your slop and how bad 1 to 2 mm. Basically a shim or different hubs altogether like hpp would be better. If shimming u have to get one small enough in diameter to just ride the inner race of bearing .
Great demonstration on changing the gearing. On the higher gearing, faster speeds, were you able to notice any lag in acceleration?
Thx!
Steve S ya it definitely with the different set ups. It was mostly due to the batteries more than the gearing. The 6s accelerated like a bat outta hell in both gearing set ups and the 4s was a bit more tame! Thanks Steve!
Man you need to try the dboots katar tires and watch how much faster it'll go
You should try it on 23/50 its a beast
your erevo sounds more quiet than mine..you should check out SRC road crushers tires for your speed runs and then post another vid.
+stickaman Will do man thanks!
my custom setup has only a metal spur gear off the clutch gear to the drive shafts going to the front and rear .... it has almost no top speed the more you stay on the gas the faster it will go .
Wrong tires for a speed run anyway. btw if you want more power use 30c+ lipos.
good Lipos make a huge difference.
the higher see lipo just means that when you pull the trigger all the way you get more power instantly not necessarily more speed but the torque increases really crazy versa 35c vs. A.50 see when you nail it because you get a hundred c of current through a 50cc battery burst
Damn ricky I might have to get an e revo cuz of your vids haha if I could get over the car customization bug I got right now I'd be all over it ha
lol ya they are a blast! thanks man and we love the custom rcs man!
Ricky Revo rc thanks! But I actually meant my full sized car lol working on customizing it. Adding Horse power, improving handling and visual appearance
i can dig that too i have a 1970 chevy nova!!
i have an e revo to but nothing beats the fun of nitro! try one
I will! Thanks
I Wonder How Fast If Added A 50t Spur Gear?? Probably Another 10mph?? That Would Be Coooool!! 😊
Only one way to find out man! Give it a whirl!
I like the body cool paint scheme
Thanks bro I appreciate the comment man!
Sick video! Thanks for sharing. Subbed!
thanks bro subbed back man!
Fabricate tires out of hockey pucks ...😂🏎
Thumbs up good video editing 👽👍
Dang I made 45 on 3s.... Stock gearing and 4000kv setup
Hi, I recoomend Truggy tires for speed runs. I use medium compounds ( hard ) and the car is still controlable. In my opinion street tires blow too much.
sweet bro thanks for the tip! I will be looking into a set!
Hey Ricky. I have the same axial wheels with Trencher X's. Did you ever have an issue with the inner beadlock ring on the front cutting into the front lower A-arms? And if so, what did you do to fix it? Thank you.
+ba8089 yes I did! you can do wheel wideners. I just ended up putting different wheels on!
Thanks! Also Did U Need Any Wires To Phone To Measure The Speed??
nope all gps just open the app strap it to your car and go and hopfully it doesnt fly out of the car at 60+ mph lol!!
Ok Awesome, Thanks Again!! 👍 👍 😊
Geiler Bart junge wie lang ist der mach mal ein making of
Hey Ricky quick question about the spur gear on the Erevo. I run (2) 3s lipo in mine and I go through a spur gear about 2-3runs every time. Got the mesh set up right. Tried the paper trick, even tried moving the motor under easy acceleration so find that sweet spot where the gear mesh runs smooth. U ever had this problem before or got any tips thanks.
+Abram Hart Is it stripping the teeth or is it melting?
+Ricky Revo rc the teeth are wearing out. After a few runs u can see wear marks on them. I've tried backing the slipper 1/4 turn to 2 full turns results are the same. Nothing looks bent heard spin with no wobble.
make the mesh tighter than you normally do!
How do you like the big Joes ?? I am in the process of getting a Emaxx brushless with them on it
Elite Status I love them they have superior Traction over a lot of tires........BUT your drive-train will not like them!! I have a new set of tires in route for my e revo I have done 3 rear diffs since these badass tires!
Very cool. THX :)
Thanks awesome vid, saved me a lot of time.
Stupid Fast RC Your welcome!
Great video! Thx man!
Hey man how are you
I'm getting 3s lipos soon and was wondering what parts to upgrade besides from driveshafts and shimming diffs....
+Daniel Rc you should be ok with those upgrades! make sure your slipper is adjusted according to your driving style and try and stay on off road surfaces to minimize strain on your drive-line.
+Ricky Revo rc how did you get it to not do a wheelie??
+Nathakrit Apithanangsiri Just ease into the throttle rather than just pulling the trigger. when I run 6s I just use the wheelie bar at the lowest setting @ 6:00 in the video!
Very nice vidéo Thank you
good stuff
Great vid, can u tell us what tires and rims u r running!
Thanks bro I appreciate that!! The tires and rims I,m using are axial 40series bead-locs with big joes for tires. they're great for most terrain but i wouldn't recommend them for high speed street use lol!!
Ricky Revo RC sorry I'm viewing this video so late, but would you recommend 6s over 4s, I've heard 6s is to much
Matt Gibbons I run my e revo on 4s with a 65t spur gear. It runs between 35-37 on a good charge. In my opinion, 4s is just fine for me
nice car
Mas jhon Thanks!
all those upgrades and still running stock driveshafts? mine blows them on 6s every few batteries
no they're Summit driveshafts 10 times stronger than stock!
+Ricky Revo rc ohh yeah sweet! im running steel upgrades
Cool, Thanks Again!!😊
good vid bro
another quick question i see some videos where they have full throttle and the revo goes when i drive mine it sounds like its spinning the spur gear before it takes off so theres no tire spin at all or the truck does not flip
Yea it sounds like you have your slipper adjusted correctly! As long as the noise goes away after a foot or two!
Ricky Revo RC yea it does so it probably needs a half turn or 1 full turn i guess
Sure just make small adjustments until it sounds right to you and your driving style!
Ricky Revo RC yup u nailed it the screw was super loose I gave it 1 1/2 turns and now it drives perfect puts the power to the ground wheelies ect and thanks bro You the real MVP quick responses and all can't wait for more videos !!!
So I have a question when you say 4s is that 2 2s baterteries or 2 4s? And same about the 6s?
2 4s batteries
get foem pavement tires or some speedtreads Street Fighters
get some street tires will be more stable and not balloon so much. ohh you said at the end sorry
wheeli on 4s?
What App Did U Use On Your Phone??
Just search speedometer in the app store theres a few different ones. This one was ulysse speedometer
What app where you using on the droid
ulysse speedometer
What kind of tires are those and where do you get em?
+Cody Groves Pro-Line.com they are the big joes
See you later Nitro!!!
Pablo Donato haha ya electric cars are flying these days!
Can you bash on the smaller spur?
+Daniel Rc yep thats the gear I have been using and it works great!
+Ricky Revo rc thanks :)
+Ricky Revo rc thanks :)
Wich battery is more durable?
both are pretty good batteries.
Get those belted monster truck road crusher tires on sweepracingusa.com they don't balloon at all and look nice you'll see how fast that erevo can go!!!
Should I get 4s or 6s to run in my E REVO
+Botman I run 4s for general bashing and ripping it up. i dont usually run 6s. Check out some of my other erevo videos they are all on 4s!
+Ricky Revo rc ok :)
a whllie bar!
can i ask what turn motor u run in ur e-revo
I honestly dont know its the stock 2200kv motor. I looked around for the turns but had no luck!
I think it's some sort of mamba monster. Have fun finding the turns for it
wheelies are still cool
+Jason Parker I agree!
my slash 4x4 goes 70 and my rustler goes 94.
robert shea the rustler goes 94 WHAT Btw is it the rustler 4x4 or the normal one
theres no rustler 4x4 only 2wd
@@sethhai1536 there is a 4x4
Ricky Dicky Doo I want to ask you a ? I would like to know.. What Pinion Gears I should Place on my E-Maxx Brushless to Get it to do Wheelies. I am Running Lipo3's x 2 for The Traxxas E-Maxx Brusless. Can you suggest something good for me? I like your Video. I 'm going to Subscribe to you. Currently I have a 1969 Dodge Charger on my E-maxx PAINTED To a TEE ! It is SICK Looking. I will try 2 post a Video for you to see my Truck. I have NO Videos on my U Tube cause I never knew how to do it. I am Waiting to take my Truck into hobbie Hole so they can do ALL the Tellementrys for me. I am a NEW-BIE 2 it. lol
I hope to hear from you Ricky D
+Dr. J. K. Gallagher. you can just tighten up your slipper clutch to do wheelies but I wouldnt leave it tight for too long cuz your drive train will start taking a beating and thanks man!
oh ok thanks Ricky. :D
I really like your ride. Radical.
thanks bro!
Niiice
can someone tell me if I get a e revo is it worth it to get 4s or 6s
Matt Gibbons I run 4s for general bashing and having fun! if I have a big open area to really open it up, I run 6s. check the website in the description for more info and a product review of the car
Ricky Revo RC Okay, thanks!
my volcano does 64 on 3s 21 64
That was freakin awesome ricky I've been wanting to do speed run's on my 3 trucks my daughters has my gps any who lol I just wanna get videos of going fast but I don't know if my vehicles r set up good enough we will see hear pretty soon crash n burn always makes for good videos lol thanks for your cool video buddy I gave you a big shout out on my traxxas e revo tutorial and shout out vid I would be honored if you check it out thanks buddy you have kik ass videos👍👍👍👊
I watched and gave a big thumbs up Thanks so much Roy! just run that thing how it is my car was set up for bashing nothing special! try it out see how it goes!
Ricky Revo rc will do brother thanks a lot man we drive like we stole them lol makes for good videos brother I'll be checking out some more of your video soon you always have good vids man and thanks for checking out my video much appreciated brother👊👊👍
my slash can do 55 on 3 s wtf that thing must wheigh a ton. on 6 s my car would fly
LOL! 13lbs
Michael Mack 3s at 55mph on stock vxl will burn out motor or esc. we're talking 2200kv motor that can run all day on 6s without getting hot. your slash does not have more power it's just over geared.
Michael Mack and on 8s the thing will explode
whr I can gt dis car
ebay
Hw much cost
700-800$
when you don't want that Texas anymore give it to me
Jalen Jones its traxxas u dumb noob and he is never gona give it to u u are really dumb
needs to be nitro powered
I would like a REVO 3.3.