@Dario-h8g @Dario-h8g If I can do it, you can do it!. This guy's video helped me quite a bit: ruclips.net/video/3O0vGfiQ7EI/видео.htmlsi=gSkDaib9K5h72uYA Keep wrenchin, brotha 💪
I'm gearing up to do mine right now. Your video was pretty straight forward informative. I'm in Texas, but understand Canadian quite well , lol. Good content buddy.
Thank you very much! I've put around 1000 km (64 miles) on the truck, and it's still working! If you haven't found it already, here's a more detailed video I used for my job. ruclips.net/video/3O0vGfiQ7EI/видео.htmlsi=zjTHdG34SZRvy-cY
It was a good video for watching after viewing more detailed ones. I'm about to rebuild mine with 225k on it. It works fine, but I want to know I can travel coast2coast. Upgrades for towing are on my list of parts. Fortunately, I bought my 07 TBlazer for less than 3k from original owner, that happenedto own the local Chevy dealership... so spending 5k to totally refresh all parts ignored is ok. I was surprised you did not use some type of band clamp to perfectly mate the pump halves. Now to search for your follow up vid
@@RegenAutomotive There is a need for transmission builders. Just from what you have shown, a transmission shop would hire and train you. By the way, trying to reuse that original forward sprag would have been a mistake. Going with the hardened Borg Warner sprag was best.
@gearshifterg9756 Thanks again. I appreciate the kind words! Rebuilding a transmission has always been a bucket list DIY of mine. Next, I am going to rebuild an LS engine and play around with a custom engine stand and tuning. So, stay tuned!
No problem. Below is a link to a video that helped me do mine. Let me know if you have any questions. Good luck! ruclips.net/video/3O0vGfiQ7EI/видео.htmlsi=WhgiRSpHxSj7GQJN
man I wish I saw this video earlier. So much conflicting information online. Ended up installing the low reverse piston wrong and as a result couldn't get the parking brake lever in. Had to take it all apart again and reassemble lol. Almost done with the rebuild. will see if it works on the weekend.
If you do 1 in the future use a cheap strap. It will go in the bottom of the output shaft and hook it to the top of the case. Tighten n it will hold it up for you. N then you can use a screw driver to force that snap ring in.
Not bad. My first 1 I didn't do bushings. Do it on just about everyone know. N I didn't see you replace ur white seals on ur input shaft. Probably cause you didn't have the resize tool. No biggy thou. Very clean thou n that's what matters
It is Very Interesting to watch and learn.
@@JackieElder-v7f Thanks! I thoroughly enjoy doing this stuff.
life is about Trial and Error!!!! ive done Engines my next goal is to Rebuild my 1997 astro van 4l60E!! thanks for Sharing!!!
@Dario-h8g @Dario-h8g If I can do it, you can do it!. This guy's video helped me quite a bit: ruclips.net/video/3O0vGfiQ7EI/видео.htmlsi=gSkDaib9K5h72uYA
Keep wrenchin, brotha 💪
thanks for Sharing
I'm gearing up to do mine right now. Your video was pretty straight forward informative. I'm in Texas, but understand Canadian quite well , lol. Good content buddy.
Thank you very much! I've put around 1000 km (64 miles) on the truck, and it's still working! If you haven't found it already, here's a more detailed video I used for my job. ruclips.net/video/3O0vGfiQ7EI/видео.htmlsi=zjTHdG34SZRvy-cY
It was a good video for watching after viewing more detailed ones. I'm about to rebuild mine with 225k on it. It works fine, but I want to know I can travel coast2coast. Upgrades for towing are on my list of parts. Fortunately, I bought my 07 TBlazer for less than 3k from original owner, that happenedto own the local Chevy dealership... so spending 5k to totally refresh all parts ignored is ok.
I was surprised you did not use some type of band clamp to perfectly mate the pump halves. Now to search for your follow up vid
@@davepetrakos1192 Thanks for watching.
While it is obvious there was minimal transmission experience, it is a wonder this transmission actually worked.
@@gearshifterg9756 Thank you, sir. I will take that as a compliment!
@@RegenAutomotive There is a need for transmission builders. Just from what you have shown, a transmission shop would hire and train you.
By the way, trying to reuse that original forward sprag would have been a mistake. Going with the hardened Borg Warner sprag was best.
@gearshifterg9756 Thanks again. I appreciate the kind words! Rebuilding a transmission has always been a bucket list DIY of mine. Next, I am going to rebuild an LS engine and play around with a custom engine stand and tuning. So, stay tuned!
thanks mate i'll be doing my 06 hummer transmission asap as well, cheers
No problem. Below is a link to a video that helped me do mine. Let me know if you have any questions. Good luck!
ruclips.net/video/3O0vGfiQ7EI/видео.htmlsi=WhgiRSpHxSj7GQJN
man I wish I saw this video earlier. So much conflicting information online. Ended up installing the low reverse piston wrong and as a result couldn't get the parking brake lever in. Had to take it all apart again and reassemble lol. Almost done with the rebuild. will see if it works on the weekend.
@@arsenbassenov1685 Thanks for commenting. Good luck this weekend!
If you do 1 in the future use a cheap strap. It will go in the bottom of the output shaft and hook it to the top of the case. Tighten n it will hold it up for you. N then you can use a screw driver to force that snap ring in.
@nickheiland3397 Funny, you mentioned that. I used that method, I just didn't show it in the video. Thanks for watching!
Nice work!
Thank you very much!
Not bad. My first 1 I didn't do bushings. Do it on just about everyone know. N I didn't see you replace ur white seals on ur input shaft. Probably cause you didn't have the resize tool. No biggy thou. Very clean thou n that's what matters
Haha the coffee comment got u a like and a subscribe
@goingb Thanks, Brother. Stay tuned for some more DIY and flip videos!
Hi, did you need to reprogram the tcm having using the same transmission? If yes, which scanner did you use
@josebocardo571 Hi. I did not need to program the tcm, and I had no issues. Thanks for watching!
Can't wait for it to be dropped in the Yukon!
LOL. Hopefully it works 🤞
i want to see if it works
You bet! Here's my video of me installing and testing it: ruclips.net/video/biRDQhGKx6A/видео.htmlsi=0IKqBF36dhg2-eo-
Is that a Blackstone hat?
Yes lol