How To Make Simple and Cheap Brushed ESC For RC Airplanes. DIY 18A ESC
HTML-код
- Опубликовано: 2 окт 2024
- How To Make 18A Brushed Electronic Speed Control. (single direction)
Materials:
Arduino Nano (Klon): www.banggood.c... or www.banggood.c...
IRFZ44 N Channel Mosfet: www.banggood.c...
10K resistor and 1K Resistor : www.banggood.c...
1A or 5A Diode (1A diode is enough for a motor that draws 4-5A as in the video)
www.banggood.c... or www.banggood.c...
7805 5V regulator IC: www.banggood.c...
Mini Heatsink: www.banggood.c...
JST conectors & cable (Male and Female): www.banggood.c...
PCB Board: www.banggood.c...
100nf (0.1uF) capacitor: www.banggood.c...
330nF (0.33uF) capacitor:bit.ly/2xgfTwU
Other Materials:
Wire Stripper Crimper: www.banggood.c...
2S 7.4V 450Mah LiPo Battery: www.banggood.c...
Lipo Battery Charger: www.banggood.c...
DC 180 Motors (39000 RPM): amzn.to/35rD8Ar or bit.ly/2L62JqC
108mm Propellers (CW&CCW): bit.ly/33MPMbY
Code & Diagram: bit.ly/3aNNs79
Hoe To Make 6 Channels Radio Control (Video Link): • DIY 6 Channels Radio C...
All of my videos: bit.ly/2Z9QVYK
Thanks For Watching And Please don't Forget To Like, Share & Subscribe For More Awesome Videos.
KendinYap Channel / @kendin-yap
Türkiye'de bu konudaki tek RUclips kanalı. Daha gelişmiş modeller yapabilirsiniz daha gelişmiş model ucak ve kumanda bekliyorum
You are the best in this field
Thank you sir but can make a brushless motor drone esc please sir. Sorry sir my English language is not good please make for project
you can white and learn some English using the Google translator
Güzel olmuş elinize sağlık aynısını fırçasız motor için de bekleriz.
Please Make a video, creating an ESC of 30 or 40 amps.
40 amp
@hay man You need minimum 30Amps for a good BLDC drone motor
Hocam bir arduinoyu hem kendin yap alıcı hem kendin yap esc olarak nasıl kullanabilirim projemi bitirmem lazım acil yardımcı olursanız sevinirim
The esc looks heavy tbh. Can you please make a PCB version of this ESC
Maybe Smd version.
@@yaimem please send me
@@yaimemplease can you upload your design to some server an share the link?
Thank you for your work and dedication. It was the inspiration to build my first rc plane.
Vay anasını be yeni keşfettim bu kanalı helal olsun bide türk🇹🇷
Eğitici olmuş gerçekten. :) Videoların devamını merakla bekliyoruz.
Wow... Its interesting.
Is it possible to make arduino-ESC for brushless motors?
I think, we can use 3 arduino outputs, one for every coil and then generate impulse meanwhile we using delay:
Delay = Thrust level.
Turn on 1st coil
Delay
Turn on second
Delay
Etc...
P.S. I apologizing for mistakes - english isnt my first language.
So super nice
NYC video its amazing
What are the purposes required in order to make the plane
See the rc plane video on his channel
Can we use 11.4v battery
Bro you have not made video for rc transmitter and receiver u made in previous video
Range test..... Video
Our flight area is closed due to corona virus restrictions. I'm waiting for it to open. I will do it at the first opportunity.
Why is the diode necessary?
Can we operate this esc with 12v battery instead of 7.4v battery? Please reply, by the way nice video. 👍👍👍👍
Yes (input 7-12V)
thanks for the video. What should be modified to adapt this circuit to 40 amps
Just replace mosfet. Use one N channel mosfet of 350W or above
Sir, can i use NRF24l01 as transmitter and receiver instead of ready-made? if yes, then can you please tell me where can I connect those NRF24l01 terminals in the given circuit ? thank you.
please how many distance go?
Hi! Thanks for video! You are great as usual.
As per Datasheet for IRFZ44, Gate Threshold Voltage from 2.0 till 4.0v, so, MOSFET will heat www.farnell.com/datasheets/140113.pdf
In my opinion, better to use IRLZ44N. For this MOSFET Gate Threshold Voltage is 2.0v only, so, it will be fully open and will not heat. Or, IRL3705N N-channel Hexfet Power MOSFET.
This transistor is able to withstand a continuous current up to 89A (of course, with a heat sink) and opens with a 1V voltage gate (VGS (th) parameter). Therefore, we can directly use this transistor to the legs of the Arduino. When the transistor is fully open, the source-drain resistance is only 0.01 ohms (RDS (on) parameter). Therefore, if an electric motor 12 V, 10 A is connected to it, the voltage drop on the transistor will be only 0.1 V, and the dissipated power will be 1 Watt.
And, if you use it with your great DIY RC, maybe better to make in on one PCB and didn't use additional Arduino?
Thanks for the valuable informations. The reason I use IRFZ44 is because it is cheap. In my country, IRLZ44 is twice as expensive. IRLZ3705N is 5 times more expensive. The title of my video is "Cheap". But there will be those who want to use it because they are more efficient.
I used an arduino separate from the arduino on the receiver. Because I want it to be independent. Thus, it can be used with different brand buyers.
@@Kendin-Yap Sir plz tell me that, can I use any other microcontroller like Attiny85, Attiny13a, Atmega8a,Atmega168, or other instead of arduino nano or pro mini....
Plz sir reply..me...
Can we use IRLZ44n mosfet instead of the IRFZ44n mosfet? Because in my locality this one is not available
Yes you can
Fırçasız motorlarda kullanmak için neler yapmalıyız ve çektiği akım stabil olur mu? Örneğin 40A kapasiteli yapmak için neleri değiştirebiliriz?
Fırçasız motor ESC leri çok farklı ve komplikedir. Bu devre üzerinden değişiklikler ile olmaz. Onlarda 3 faz var.
Güzel olmuş. Elinize sağlık
elinize sağlık çok güzel olmuş sizden bir ricam var şarjlı tonavida videosu bekliyorum
best video i have ever seen in making esc great job
Emeğinize sağlık çok güzel proje tesekkurler
How This Aduino Nano made I'amKurdish
Nice !
Can we use this esc with flight controllers for drones
Bende çok ilgim var bunlara Gereken Malzeme yapıp Kanalın isminde yazıldığı gibi kendim yapacam çök güzel 👍
İyi günler. Bu esc nin RC araba için ileri geri versiyonunu nasıl yapabilirim. Şimdiden teşekkürler
Dear sir, I have successfully completed the transmitter system. And now I want to make the ecs for 180 dc motor and the receiver system, but I have one arduino nano board, I want to the esc and the receiver programme in the same arduino nano board. Is it possible? If possible please tell me how can I make the system and give me the programme file,,, thanks a lot, I'm from Bangladesh.
It maybe possible I have no clue about it but there is a simple way that I think will most probably work that is using attiny85 which is pretty cheap as the micro controller for making the brushed esc . I have not tried it but I usually use an attiny85 instead of Arduino when only 1 pin is required:))
Abi daha düşük maliyetli şeyler yaparmisin benimde bu tür şeylere ilgim var ama maddi anlamda zorluk çekiyorum
Dear sir,
1. Can I use p55nf06& mosfet instead irfz44n mosfet.?
2. Can I use 10k normal resistor instead 10k pull down resistor.? Cause I can't found the pull down resistor.
1 - Yes you can. (any N channel power mosfet)
2- Pull down resistor is normal resistor. "Pull Down" is the task of 10K resistor in this circuit. That's why it's called this way.
@@Kendin-Yap1.
I use brown, black & orange color band 10k resistor but it not work😭😭😭
In your video you use broun, black, black, red colour band resistor....
And
2. when my throttle position is middle the motor run in full speed
But when I increase the throttle the motor run in slowly 😭😭😭😭😭please help me,, I try again and again but it not working
Is this 2 difference color band resistor is same?
@@softkhabbab3222 just reverse your throttle channel
Hocam youtube de ne arıyorsam bir şekilde size çıkıyor sizi izleyerek herşeyini kendim yaptığım bir rc model yapıcam şuan sizin videonuzdaki alıcı verici sistem için kargolarımı bekliyorum herşey için teşekkürler
Same for me. I planned to make the 6 channel transmitter and receiver from another tutorial from Kendin-Yap. Now, again, I came back to the channel for the ESC tutorial.
can I use an Attiny 13a in place of an Arduino?
Can I use atmega328p Au ic instead of arduino nano board
adam yapür yaaa
11 V bir dc motor calistirirmi 12V pil ile
Hi my friend. Is it possible to create bidirectional function using Hbridge mosfet. And the middle joystick as the stop function.
It is possible, but much more sophisticated code is required.
nice video, amazing skills, i really enjoyed your channel. Can u make a video (if is possible) about how to upgrade the range of a basic stock radio control? (like the radios supplied in cheap drones)
thanks
good
emeğinize sağlık . ama birşey soracam müsadenizle,
daha önce yapmış olduğunuz kumanda ile çalıştırabilir miyiz.
Mümkün ama gaz kanalı değerleri uyuşmayabilir. Değerler üzerinde biraz deneme yanılma yapmak lazım.
@@Kendin-Yap hocam 10k direnci normal dirençle yapabilirmiyiz
❤❤❤❤❤
You have some serious soldering and component leg bending skills😓
Selam abi 170gr agirlikla
Motor olarak 8520
Pervane olarak 55mm
arti olarak sizin yaptiginiz ucuz fircali esc yi kullanarak bir mikro quadcopteri ucurabilirmi
attiny85 is your friend. The Arduino nano is great but so insanely overpowered (and heavy if your using it on a micro aircraft) to read 1 pin, then drive only 1 pin.
at the moment I'm about to build it with an attiny85, but using an irf630. I don't have an irfz44, it will be a matter of testing
@@davydbar Nice. I used an irlz44 just because I have a bag of 100 laying around. The times the tiny measure on the scope were a bit off though:
analogWrite(4, map(pulseIn(0, HIGH), 1060, 1995, 0, 255));
to get the down to 0v (and the full batt voltage.)
@@williamna5800 Thanks for the information, it was very useful to me, since when I did the test the engine was not at zero.
now it works perfect!
@@davydbar Sweet! I haven't checked the attiny yet, but if you disable the interrupts on it, then just spring your own with timer you can prob. get it pretty close to the 1-2ms by counting rising/falling edge, but for throttle to a brushed motor that's mostly just being overly complex.
Hocam mW değeri nedir artınca veya azalınca ne olur 915mhz frekansı nedir ne işe yarar 1000mW 915 mhz modülle 12km menzil elde etmek istedik. Kafamız karıştı anten mhz si modül mhz si mW si alıcısı vericisi derken kaybolduk rehber video yapar mısın?
Hocam, bu esc ileri geri hareket ettirebilirmi. Tekne için kullanılabilir mi! Ayrıca fırçasız motor için esc videosu yapabilirmisiniz.
Can I operate the MOSFET directly by the Arduino nano on my diy reciever without dedicating an Arduino just for an ESC?
same question here :)
can i use irfz44n not irlz44n,i wanna use irfz44n.can i use it to make this esc?
Yes you can
can i use a non pulldown 10k resistor?
The Pull Down resistor is not a special resistor. You can use regular 10K resistors. "Puldown" is the resistor's task in the circuit.
good think
brushless icin de yaparmisiniz?
Selam abi . abi ben sundan duzetmisim ama calismiyo bana diyolarki onu bigisayara birsey yapalsin
You can instruct to do:
4 in 1 brushless esc for quadcopter
thanks
हेलो सर इन चीजों का क्या क्या नाम है
I want 4 brushed ESCs .
Is there a way that I only have to use 1 arduino four four different motors connections as many digital pins were still lift unused.
Yes, this is possible
Bu escnin arduino joystick için olanını yapabilirmisiniz
Sir, I have a doubt. How can I make this ESC Bidirectional? I need a bidirectional esc for my project as it is an rc car, and the project uses the 6 channel 2000 m+ rc transmitter and receiver from your channel.
Hocam merhaba arduino kullanmadan bir fırçalı esc yapmak mümkünmü eger cevabınız evet ise bunu nasıl yapabilirim
1 arduınoyla 4 esc yapabılırmıyızz ??????
abi uçak yapım videoları bekliyoruz bu arada bir ucağını yaptın
Abi ben de yaptım bunun aynısını fakat motor çok yavaş dönüyor li ion pil kullandım lipo yerine bide 330 seramik yerine plastik kullandım çalışmasına çLıştı fakat hem mosfet çok ısındı hemde motor çok ağır döndü mosfete mini soğutucu bağlayıp soğıtıruö ama hızı nasıl ayarlarım birde gaz kolunu aşağıya çekincede motor dönmeye devam ediyor kolu ortada konumlandurınca motor duroyor ama sanki sıkışmış gibi tiz bir ses çıkarıyor
Sir plz tell me can I use AP73T02GH-HF mosfet instead of your mosfet....and can I use attiny85 instead of pro mini or nano....
Plz sir reply me
Böyle şeyler yapabilmek için ne okumalıyız ??
Yeni kumandanın mesafe testini bekliyoruz.
Yakında. Koronavirüs kısıtlamaları yüzünden sahamız kapalı. Bekliyorum.
can i control 3 channel rc helicopter with this receiver??please answer
no you can't
Hocam yaptığınız ESC de 3S 11.1V Pil kullanmamızın bi sakıncası var mı
ESC 3S ile çalışır ama DC180 motor 3S ile yanar.
@@Kendin-Yap sağolun hocam sorularıma dönüş yaptığınız için
Can possible in reverse rotation?
h bridge, iam looking for too. if you find it, please share.
@KendinYap Excellent creation!! The motor you are using in the video does not have cooling vents unlike your other videos. What is the RPM and model of this motor?
Thanks. Its technical features are the same as the others. But the manufacturer is different.
@@Kendin-Yap @KendinYap Sir plz tell me that, can I use any other microcontroller like Attiny85, Attiny13a, Atmega8a,Atmega168, or other instead of arduino nano or pro mini....
Plz sir reply..me...
@@fuhadrock6370 yes you can. It is very much possible to make but, if you are new to electronics, you need a tutorial to follow. For now, Arduino is a good idea. Even I have zero knowledge on these microcontrollers.
Imtiaz Pakistan sandh sir ye saman Pakistan me mle ga sir please please please mjhe batao aap ke bare mhr bane Ho ge sir me aap ko bhe bht bht bht doiaey do ga good luck skrya
Rc ucak Mikro fircali motor icin mikro esc nereden bulabilirim sizde varmidir
Faz para brucheles?
Çok güzel olmuş elinize sağlık aynısının fırçasız motor versiyonu olursa tadından yenmez.
Sir can we run 775 or 555 motor by using this esc shown in video
330nf seramik kondansatör bulamıyorum, yerine 220 nf seramik kondansatör, 330 nf polyester kondansatör, yada 330nf multilayer seramik kondansatör
kullansam olur mu? sizce hangisi daha uygun olur ?
220nf seramik kullanabilirsiniz.
Can show me complete coding wihh motor 3 servo and nrf 24 module
Make a drone using this 180 motor and this esc...plz plz plz sir
Excellent, detailed and step by step videos on how to make RC planes. I hope one day you could add a video on how to make a VTOL.
Hocam merhaba acaba bunu Fırçasız motor için nasıl değiştirebiliriz. Herhangi bir denemeniz oldumu
Fırçasız esc çok farklı ve sofistike. Eskiden denemiştim ve pek iyi sonuç alamamıştım.
I want to learn to build a plane. Please, can anyone teach me?
Ben arduinodan fazla anlamiyirum klon ne anlama geliyo falan
Please make one video on coding how coding is done full video plzzzzzzzzz
ruclips.net/video/pjBnFZGfsjI/видео.html
I agree with another commenter that you should use the attiny84 or 85 chip instead of a full nano. Lot less weight and you can program them using the Arduino IDE and "Arduino as ISP".
You can leave out the nano and mount the atmega 328p chip directly on the pcb with 16Mhz crystal and capacitor. You will also need to install the arduino bootloader.
Merhaba. Eğer İstanbul'daysanız yaptığınız uçakları nerede uçuruyorsunuz?
İstanbul Model Uçak Kulübü
@@Kendin-Yap Teşekkür ederim. Klübe üye olmadan uçuş yapmak ücretli mi?
Make a ESC for brushless motor
Hocam 48v 50a civarı fırçasız 3 faz esc yapabilme şansınız var mı e bike için düşünüyorum
Please upload the video of making of brussless esc
Çift yönlü ve frenli esc nasıl yaparım?
Hii bro my arduino is resetting its self when I run 180 motor??
You are always showing nice and innovative stuffs. Is it possible to make brushed ESC using 555?
It is possible with 555 but not enough by itself. A microchip will be required. It's much easier with Arduino.
@@Kendin-Yap Sir plz tell me can I use AP73T02GH-HF mosfet instead of your mosfet....and can I use attiny85 instead of pro mini or nano.... Plz sir tell me I really need help.....
I just want that little change in your circuit of making this esc.... Can I use what I say... ..plz sir
Elinize sağlık , faydalı video...
Is it possible to control 4 motor using one arduino.?
hocam mümkünse brushell için de gösterir misiniz, amperini nasıl hesaplayacağımızı, yaka yaka bi hal olduk
Fırçalı yada fırçasız fark etmez. ESC kullanırken yapılan yaygın hata ESC nin akım kapasitesi dikkate alınmadan kullanılan uygun olmayan motor, pervane büyüklüğü, batarya voltajı gibi etkenlerdir. ESC nin üzerinden geçen akım asla üzerinde yazan akımdan fazla olmamalıdır. Hatta bir miktar altında olmalıdır (yaklaşık %10 gibi). Yani maksimum 45 amper çeken bir motoru en azından 50A ESC ile kullanmalıyız ki güvenli tampon bir alan kalsın. Bu yüzden taktığınız motorun maksimum yükte kaç amper çektiğini bilmelisiniz. Motorların teknik detaylarında bu bilgi genellikle yer alır. Diğer konu motora rasgele perva takılmaz. Pervane büyüklüğü motorun çektiği akımı değiştirir. Olması gerekenden çok daha büyük veya çok daha küçük pervane motorun tasarlandığı yükün dışına çıkacağından fazla akım çekmesine sebep olur. Bu akımı ESC karşılayamazsa yanacaktır. Çoğu marka, motor için uygun pervane büyüklüklerini, çalışabileceği maksimum akımı ve voltaj aralığı bilgilerini verir. Bunlara dikkat edilirse ESC leri uzun süre güvenle kullanabilirsiniz.
Hocam tek arduinodan hem alıcı hem esc yapılmaz mı
Yapılabilir.
Denedim harika çalışıyor :) hatta daha önce yaptığınız arduino alıcı ile birleştirerek yaptım çok ufak bir paket haline geldi. Bu alıcıya lipo pilden gelen voltajı okuyup pilin nominal gerilimine yaklaştığında yanan bir led eklemeyi düşünüyorum acaba bu ekleme gereksiz yere pilimi tüketmemi sebep olur tam kestiremiyorum tecrübesi olan arkadaşlar var mı bu konuda ?
Led yaklaşık bir saat çalıştığında 20ma tüketir. Yani tüketimi hiç önemli olmaz.
@@Kendin-Yap merhaba flysky6 kumandanin alicisi escyi goruyor servo calisiyo fakat motoru calismiyo sorun neden olabilir acaba