Got my orange rx tx 10channel mode1 transmitter about 1 hour ago.you said it was a matter of 2 screws to change the mode and you were right! It is now a mode 2 transmitter! Thanks for the information good buddy!
Hi, I have just returned to model making after my retirement, I have a HobbyKing Orx T-6. Everything works fine EXCEPT the ailerons. The right-hand control has no effect on the ailerons on the monitor the pointer does not move. I must have at some time made an adjustment that has affected this. Please can you advise how to return this to travel left and righthand. I hope someone can help with this. the local hobby shop is not keen to help because I purchased this from HobbyKing.
@@collingwoodboy not really without replacing the gimbal but you can get some decent cheap radios at the minute that are much better than your original
Good morning Mr Colski Rc,when i take the back cover off from the orange rx tx 10i transmitter is there a video that will show me where the 2 mode change screws are located or can you tell me! Thank You friend.
Just one really bad downside. The rotary programming switch is really badly designed, it has a tiny shaft which snapped off after very little use. Fortunately I have a lathe so fashioned one out of brass. One way to help avoid breaking this is to only click down at the top of the dial as this is where the button is and the offending shaft is at the bottom where it goes into a rotary switch. Be warned! Nice unit otherwise.
Got my orange rx tx 10channel mode1 transmitter about 1 hour ago.you said it was a matter of 2 screws to change the mode and you were right! It is now a mode 2 transmitter! Thanks for the information good buddy!
Hi, I have just returned to model making after my retirement, I have a HobbyKing Orx T-6.
Everything works fine EXCEPT the ailerons. The right-hand control has no effect on the
ailerons on the monitor the pointer does not move. I must have at some time made an adjustment that
has affected this. Please can you advise how to return this to travel left and righthand.
I hope someone can help with this. the local hobby shop is not keen to help because I purchased this from HobbyKing.
It sounds like a failed potentiometer rather than a setting issue.
Has the controller been unused for a long time?
@@CKone41 Thanks for answering Colski. yes it's been 4 or 5 years is there anything I can do to put right
@@collingwoodboy not really without replacing the gimbal but you can get some decent cheap radios at the minute that are much better than your original
Nice..Is there a port for flight sim for this? and does it keep the trim settings after turning of tx?
Hi sorry for the delay yes it has the trainer port to allow for plugging into a pc for a simulator and yes it holds the trim positions for each model.
You can adjust the ratchet just peel back the rubber grip
flying r/c adventures can i change the mode from 1 to 2 by peeling off the rubber grips or will i have to take the back cover off? thanks!
Can I use a spektrum as trainer with this orangerx?
Can I connect the orange rx wired to pc for simulating programs?
Hi yes you can use it on your pc but no it won't connect to a spectrum for training
@@CKone41 is the wireless dongle needed for the pc simulating Software? Or can I use the USB cable?
@@mirkotram5306 you will need a dingle
Good morning Mr Colski Rc,when i take the back cover off from the orange rx tx 10i transmitter is there a video that will show me where the 2 mode change screws are located or can you tell me! Thank You friend.
lee jimerson Hi I don’t have mine anymore but I think there is a video on RUclips it’s very easy
@@CKone41 Thanks !
I know I am kind of randomly asking but do anyone know a good site to stream new movies online?
@Alijah Franklin i watch on Flixzone. You can find it on google :)
@Alijah Franklin i would suggest Flixzone. Just search on google for it =)
what is the name of that little drone and where can i get one from?
lee jimerson that is a nano qx fpv they don’t make them anymore but there are normally a lot for sale on eBay
Thanks i will go to ebay and check it out!@@CKone41
Mr colski rc does the mode change from 1 to 2 is it the same for the orange rx tx 10i dsm2/dsmx ?
Hi yes it is exactly the same on the 10i
Thank you very much my friend They only have the mode1 at the us ware house, now i will order one ! Thanks again@@CKone41
Hi
Thanks for that I hadn't realised
Just one really bad downside. The rotary programming switch is really badly designed, it has a tiny shaft which snapped off after very little use. Fortunately I have a lathe so fashioned one out of brass. One way to help avoid breaking this is to only click down at the top of the dial as this is where the button is and the offending shaft is at the bottom where it goes into a rotary switch. Be warned! Nice unit otherwise.