Install Crown Molding with the Kreg Crown Pro™

Поделиться
HTML-код
  • Опубликовано: 29 окт 2024

Комментарии • 59

  • @answersfromabove
    @answersfromabove 2 года назад +4

    This guy is so clear and easy to understand. Just enough info to get the job done right without over talking.

  • @mie2263
    @mie2263 Год назад +1

    After watching 15 different videos, finally found one that is clear and explained from A to Z, thanks

  • @kingofthedads
    @kingofthedads 6 лет назад +2

    Excellent video! Very well explained and very informative.
    I used the wood corner shim as explained when installing my kitchen crown molding a few weeks ago and it worked great. Thanks again for the tip.

  • @48haburt510
    @48haburt510 6 лет назад +2

    Awesome jig. First time installed 5.25 dentil crown and came out perfect.

  • @tonydibratto5333
    @tonydibratto5333 5 лет назад +2

    Excellent video. Can you explain how you transferred your stud marks which you made above the chalk line so you visibly could tell where to nail. Once you hold up the crown molding, you would not be able to see the markings. Thanks

  • @ALEJANDROReyes-cb9ce
    @ALEJANDROReyes-cb9ce 3 года назад

    Thank you so much for your information and videos explained about how to cut crown molding

  • @alimabraham744
    @alimabraham744 3 года назад

    Man you are the best thank you for all your hard work and beautiful details

  • @jaredhoffmire35
    @jaredhoffmire35 4 года назад +1

    Best video on this by far. Thank you

  • @danielhuynh01
    @danielhuynh01 4 года назад +1

    Great video, you'd made it look simple. Thank you sir for all the tips

  • @johnvgig
    @johnvgig Год назад

    Kreg is a huge company. WHY is the audio only one channel (left)?!?!

  • @snaplove7931
    @snaplove7931 8 месяцев назад

    the best video on this !!!!!!

  • @redbuds69
    @redbuds69 3 года назад +2

    Little did he mention that this is a extremely dangerous jig. The short cut off pieces fall in the blade path & get flung across the room. His 3rd cut did just this but got lucky & didn't fling out.

  • @docdoctme
    @docdoctme 3 года назад

    Great video! Thanks for sharing.

  • @tonypolito8930
    @tonypolito8930 3 года назад

    Very Good Job! Just wanted to ask, would coping the corner an option?

  • @jpramos5959
    @jpramos5959 2 года назад

    When you cut it that way, do you always cut at a 45 angle?

  • @LightGesture
    @LightGesture 3 года назад +2

    Or you find where you need to set your crown, glue a stick on both sides of your miter saw.
    Then you can do long pieces and not have to dickaround with raising your work piece up so far where you are squeezing to be accurate.

  • @ALEJANDROReyes-cb9ce
    @ALEJANDROReyes-cb9ce 3 года назад

    Have a wonderful day sir God bless you 🙏

  • @richardsullivan5004
    @richardsullivan5004 4 года назад +3

    What degree do you set the miter saw cut?

    • @AN-kg4ei
      @AN-kg4ei 4 года назад

      Half of whatever wall angle you measure as they never seem to be dead 90d... Using an angle finder tool is a great plan especially the ones that lock or have illuminated digital readouts as they come in handy at the saw if not writing everything down...

  • @1topscout
    @1topscout 4 года назад

    Wow! Excellent tutorial!

  • @tomekberg9252
    @tomekberg9252 6 лет назад +1

    Nice job explaining this!

  • @lynnvincent6933
    @lynnvincent6933 5 лет назад

    well I don't pop a line on the walls I pop my line on the ceiling walls can be waive and if you nail the wall first your crown will follow the in and outs try and look down a long wall along the ceiling after you install your crown and you will see what I am saying just trying to help also good video on the Kreg crown pro

  • @PedroRodriguez-hy5ty
    @PedroRodriguez-hy5ty Год назад

    How about on concrete walls let me know thanks

  • @ko6128
    @ko6128 5 лет назад +2

    Why is a chalk line necessary? I shove the crown in the corner and get it tight against ceiling and wall and fire away. No dealing with chalk. An angle measured on a corner won’t be the same as what is set on the saw. Both devices have variances.

    • @86ortega
      @86ortega 2 года назад

      Do you skip the furring

  • @wayne0425
    @wayne0425 5 лет назад

    Great video, very helpful, thanks

  • @tsnstt
    @tsnstt 4 года назад

    I don’t understand the upside down before cutting. If you have the jig why flip the crown upside down?

    • @vinceh8468
      @vinceh8468 3 года назад +2

      Since crown molding is measured to the length of the bottom of the molding then cutting the crown molding upside down has an advantage in that the mark at which you want the cut to be located is then closest to the blade. You can test the position of the piece relative to the blade while the saw is off by lowering the saw blade and adjusting the precision of the blade cut. Cutting the crown piece the right way up then the pencil mark will be away from the blade - a bit more difficult to get the cut precise unless your saw has a laser guide?

  • @jamessilverman4887
    @jamessilverman4887 4 года назад

    I want to install crown molding above a window a foot below the ceiling. How would I secure it?

  • @reidcross9051
    @reidcross9051 5 лет назад

    how do you decide the width of the furring strip?

  • @julianarodriguez3635
    @julianarodriguez3635 3 года назад

    How you installed crown molding on concrete walls let me know thanks

    • @JJ-cf4gz
      @JJ-cf4gz 3 года назад

      Add strips of lumber to the wall with concrete fasteners and adhesive .Then install over the top .

  • @BoredAtWork2000
    @BoredAtWork2000 4 года назад +5

    You never came back to making cuts that aren’t 90 degree corners

  • @jayasreepisupati3574
    @jayasreepisupati3574 4 года назад

    Other than setting spring angle on the jig and 45 deg on the mitre saw, is there anything else to take care of before the cut?

  • @josemanzanares8316
    @josemanzanares8316 5 лет назад

    Nice video!

  • @LightGesture
    @LightGesture 3 года назад

    Baby powder works better than chaulk. Mix it with some blue and you'll be gravy and smellin as clean as a fresh daiper. Lol

  • @nickhuber9627
    @nickhuber9627 5 лет назад +2

    Should be coping all your inside corners. Never have a gap, if you do it right.

  • @gabegiguere1393
    @gabegiguere1393 4 года назад

    Love your video very helpful thank you . if you have some free time could you swing by and help me finish up have 6 more rooms to go

  • @wutangmaster357
    @wutangmaster357 4 года назад +2

    When Using the Kreg Crown Pro why is everyone still turning the crown upside down, If you turn the jig around facing the fence then you can cut the crown molding as it will go on the wall still set your spring angle. Left inside, jig to left blade to left, for right inside blade right material right, Left outside material to Left, blade to right for right outside, material to right blade to left that's laying your material facing you with jig turned the opposite to fence

    • @dsokodrum67
      @dsokodrum67 4 года назад

      Thomas
      What do you mean ?
      Turn the jig backwards and put the moulding right side up?

    • @wutangmaster357
      @wutangmaster357 4 года назад

      @@dsokodrum67 yes if doing so the same way the molding go up is the way you cut

    • @dsokodrum67
      @dsokodrum67 4 года назад

      Cool! I will try it!

  • @cherylclear2566
    @cherylclear2566 5 лет назад +2

    What angle is the saw set on?

    • @carlcox7332
      @carlcox7332 5 лет назад

      45°unless you have to adjust a half a degree to accommodate slightly off corners

    • @carlcox7332
      @carlcox7332 5 лет назад

      For most outside corners I normally cut 45.5° so you always get a nice sharp edge. But I never do inside corners with the chopsaw like he shows personally. I like doing cope cut for insides. It allows more play for imperfections a couple degrees either way when I'm doing really decorative crown or base

  • @stevelowry6146
    @stevelowry6146 6 лет назад +1

    NIce trick, with that shim...

  • @CTRwannaB
    @CTRwannaB 2 года назад

    This thing is a death trap
    Bought it from lowes
    Returning it after 2 cuts
    Not supported correctly
    Pieces will fly off

  • @danielgeng2306
    @danielgeng2306 5 лет назад +1

    Silent movies ?

  • @jhgandy2653
    @jhgandy2653 3 года назад +1

    terrible job of expaining it idk how yall think he explained it so well I'm so confused now

  • @cliffpoff2457
    @cliffpoff2457 6 месяцев назад

    Must have missed angle adjustments.

  • @David-fg4nu
    @David-fg4nu 4 года назад +4

    Good lord, the audio in this video is ear rape

  • @jamesstanton173
    @jamesstanton173 6 лет назад +1

    I really wanted to watch this video but something is wrong with the audio and you can barely hear the guy talking

  • @AmazingSavingplan
    @AmazingSavingplan 3 года назад +1

    What happens when you have to cut a piece of 7 ½” wide crown that is 12 feet long. This tool would never work. Maybe ok for cheap contractor grade crown in tiny little rooms. Just another gadget that will not work in real world applications.

  • @romsam4234
    @romsam4234 Год назад +1

    Total BS ! Just cut on the flat, change the miter and bevel angles end of story.

  • @bayridge5177
    @bayridge5177 5 лет назад

    N