Thank you so much for sharing. I followed what you have said and my dishwasher is finally working. Thanks a lot for the tip. May God blessed you. I am going to write it down so I wouldn’t for get.
Thank you for your video appreciate your humor 😊 came across you as we were experiencing water in our GE dishwasher husband changed the drainage pump it worked and now it won’t turn on after wanting to be stagnant. Will try what you suggested and see if anything helps. It’s like the washer wasn’t completing the cycles and it stopped signaling when it was done. After he replaced again it worked but there was water in the bottom. It’s a shame that we just started using the washer in 2023 and we had our home built in 2016. Why didn’t we use it? We thought it would waste water but our oldest daughter showed that it actually saves water and so did the water bill 😂yes we were slow in our thinking. All the best to you for sharing your knowledge and expertise 😊
my issue is that the control panel has lost all lights, power and reset procedure has no effect, any ideas, kinda sounds like the control board has died?
after my diswasher comes back on i can do a cycle of dishes then it turns off after an hour, then it takes me some time to get it back on the control lock is not on though
My dishwasher fills with water. But then it just makes a click sound, then sounds like a kettle boiling for a few seconds, then stops, then does it again, and stops..... It does that over and over and never starts a cycle.... What could be the issue? It's a indecit dishwasher.
Sounds like an issue either way the circulation motor. The kettle sound is the heating element coming on something that usually comes on while circulating motor starts workings. Check the main board, it has a fuse( very small round typically dark red in color or black) check for continuity and make sure it’s not open. Last I would check resistance on circulation pump and make sure the board is sending 120v. If you get 120v you have a bad circulation motor
Clean the screw and filter at the bottom are the dishwasher turn to the left and it'll come out watch that screen really good ours did that and it fixed it
Well, apparently not all the issues are covered here... in our case I figured out that the door's right side has to go a little up for the door to get intp.the latch, and the latch start working.... and I can't figure out how to fix it... FYI, everything else is leveled...
My ge dishwasher is beeping and blinking constantly and won't start I've just changed the contol board because that is what the tech told me that was wrong it
Thank you so much for sharing. I followed what you have said and my dishwasher is finally working. Thanks a lot for the tip. May God blessed you. I am going to write it down so I wouldn’t for get.
Yep that control lock got me. I didnt even know that was a feature. Thank you!
Great video!!! I too simply reset the circuit at the power box and life was good again. 🎉😊
THANKS! You saved me arepair bill that I couldn't afford It was the control lock.
Thank you for your video appreciate your humor 😊 came across you as we were experiencing water in our GE dishwasher husband changed the drainage pump it worked and now it won’t turn on after wanting to be stagnant. Will try what you suggested and see if anything helps. It’s like the washer wasn’t completing the cycles and it stopped signaling when it was done. After he replaced again it worked but there was water in the bottom. It’s a shame that we just started using the washer in 2023 and we had our home built in 2016. Why didn’t we use it? We thought it would waste water but our oldest daughter showed that it actually saves water and so did the water bill 😂yes we were slow in our thinking. All the best to you for sharing your knowledge and expertise 😊
Thank you! I inherited this machine in my kitchen and struggle with it all the time! Now I know to look for the lock!
Thank you . I reset the circuit and it works🎉❤
How long do you stop power for a reset?
my issue is that the control panel has lost all lights, power and reset procedure has no effect, any ideas, kinda sounds like the control board has died?
WD-40 on latch catch worked! Sprayed the hinges too
You saved my life. Thank you sir.
after my diswasher comes back on i can do a cycle of dishes then it turns off after an hour, then it takes me some time to get it back on
the control lock is not on though
It was the control lock, thank you..
You literally saved my life but now I feel like an idiot it was the lock control 😂
HOW DO I TURN OFF THE DELAY SETTINGS
My dishwasher fills with water. But then it just makes a click sound, then sounds like a kettle boiling for a few seconds, then stops, then does it again, and stops..... It does that over and over and never starts a cycle.... What could be the issue? It's a indecit dishwasher.
I have the same issue
Sounds like an issue either way the circulation motor. The kettle sound is the heating element coming on something that usually comes on while circulating motor starts workings. Check the main board, it has a fuse( very small round typically dark red in color or black) check for continuity and make sure it’s not open. Last I would check resistance on circulation pump and make sure the board is sending 120v. If you get 120v you have a bad circulation motor
Clean the screw and filter at the bottom are the dishwasher turn to the left and it'll come out watch that screen really good ours did that and it fixed it
Well, apparently not all the issues are covered here... in our case I figured out that the door's right side has to go a little up for the door to get intp.the latch, and the latch start working.... and I can't figure out how to fix it... FYI, everything else is leveled...
Isn’t fuse one of the first thing to tackle first ?
Thank you so much!!!!!
I changed the control board and that didn’t fix it
Great video... thanks
My ge dishwasher is beeping and blinking constantly and won't start I've just changed the contol board because that is what the tech told me that was wrong it
usually best replace both boards
By the shore
nope the control will not unlock and disconnecting power to the dishwasher overnight won't reset it either
My lock control won’t go off either. I’ve tried holding button, unplugging, turn of circuit breaker, hard reset and nothing. Any other ideas?
Get to the point. Thumbs down
I would rather buy a new dishwasher than listen to this AI audio
wow way too wordy. get to the point
Nobody wants to hear stories about your customers and "Jerry", just get to the problem and the fix.
Thank you so very much!!!🎉