2013-2019 Ford Escape Rear Differential Oil Change.
HTML-код
- Опубликовано: 20 апр 2020
- On this episode I show you how to change the rear differential fluid on your 2013-2019 Ford Escape. This procedure only applies if you have an all wheel drive (AWD) Ford Escape. Ford says that the rear differential oil is a "lifetime" fluid and the rear differential has no drain plug. Ford defines lifetime as 10 years or 150,000 miles. Most people need to change the oil sooner than that. To change the fluid, you need to suck the fluid out of the fill hole and pump the fresh oil into the differential. I used just under 1qt of 80w-90 gear oil on this vehicle but, Ford lists the oil capacity as just over 1.2 qts. I would suggest getting 2qts. of oil just to be safe if your are looking to attempt this job. My oil came out very clean at 71,000 miles but, your results may vary.
Here are the links to the tools that I used in this video:
Some of these vehicles have Torx or sometimes hex (Allen) style fill plugs. This vehicle had a standard 3/8ths square drive. Check what you have before ordering.
Serpentine belt tool (3/8ths sqaure drive): amzn.to/2VMlm75
Low profile Trox bits: amzn.to/3cE8M0s
Low profile Allen bits: amzn.to/2zlHVb5
Fluid extractor/brake bleeder: amzn.to/2xFjuoJ
Manual Fluid Extractor: amzn.to/3eCFEIR
Fill Pump: amzn.to/2yy549X
Teflon tape: amzn.to/2RUmEfa
Help support the channel buy using my Amazon links
As an Amazon Associate I earn from qualifying purchases.
Questions? Shoot me an email at repairgeek365@gmail.com
Disclaimer:
The information, demonstration and any content contained in this video is for informational purposes only. The user Repair Geek makes no warranty, express or implied, regarding the effectiveness or safety of the contents of this video. In no way should the contents of the video, including the tools used, be repeated or tried by anyone. Viewers should only seek the help of a trained professional located at a licensed auto repair shop for any fix, modification, alteration, or any change to their vehicle. Repair Geek shall not be liable for any injury, damage, or loss to any person or property that may result from use of the tools, equipment, or any content contained in this video. In addition, there is no way to guarantee that the video is not altered or modified or is not in the final form submitted by Repair Geek and therefore, Repair Geek does not warrant that the video is unaltered or not modified. The links on this video to products are for informational purposes only and in no way are an endorsement of the safety or effectiveness of the particular product. Viewers understand that anything contained in this video or linked to or from this video is the sole responsibility of the viewer and in no way provides an express or implied warranty as to the safety or effectiveness of any linked tool, product, or video. Therefore, viewer agrees to release, waive, and discharge Repair Geek or anyone affiliated with Repair Geek, from any and all liability, claims, demands, actions, and causes of action whatsoever arising out of or related to any loss, damage, or injury, including death, that may be sustained by the viewer, or to any property belonging to viewer, regardless of whether the loss is linked to the use of the contents of this video, or otherwise and regardless of whether such liability arises in tort, contract, strict liability, or otherwise, to the fullest extent allowed by law. 
Авто/Мото
Hope you guys are staying safe out there during these crazy times. My regular job has seen a large increase in orders because of Covid-19. I realize not everyone is as lucky. Take care guys. Also, cut me some slack. I'm about 4-6 weeks overdue for a haircut at this point haha.
Here are the links to the tools that I used in this video:
Some of these vehicles have Torx or sometimes hex (Allen) style fill plugs. This vehicle had a standard 3/8ths square drive. Check what you have before ordering.
Serpentine belt tool (3/8ths sqaure drive): amzn.to/2VMlm75
Low profile Trox bits: amzn.to/3cE8M0s
Low profile Allen bits: amzn.to/2zlHVb5
Fluid extractor/brake bleeder: amzn.to/2xFjuoJ
Manual Fluid Extractor: amzn.to/3eCFEIR
Fill Pump: amzn.to/2yy549X
Teflon tape: amzn.to/2RUmEfa
Motorcraft oil: amzn.to/2VTL1dQ
Valvoline oil:amzn.to/2x2OZso
Help support the channel buy using my Amazon links
As an Amazon Associate I earn from qualifying purchases.
:)
Hi!! I got this weird behavior while turning my 2017 escape, like some skiping and bumping, while straight it doesnt happens, I requested oil change of the rear differencial...it was dry...it has new oil but it still feels the same way...is the differential dead?
Could you use the same pump for draining that you did for filling? I realize you have the pneumatic vacuum pump and it's easier, but if you only have the simple hand pump it should be able to go in from the top with an extender hose. Would that work?
How about using a very short 3/8" bolt with permanent thread locker and a 3/8" nut tightened all the way down as an insert for the plug? That way you could use a standard wrench or even a ratcheting wrench if you have one instead of any specialty tools. You could cut the bolt if necessary so it's flush with the nut when tightened. Basically it'd be making a temporary bolt head for the plug.
@FranciscoAlbMartinez 7:37
Your issue is no doubt the viscous coupler/clutch that's mounted to the front of the differential. Hopefully, you can just replace the viscous coupler/clutch, IF the splines on the shaft of the differential and the viscous coupling/clutch are not worn and rusted like mine were. I had to replace the complete RDU (Rear Differential Unit) which includes the viscous coupler/clutch.
Great video. I fully agree with your point that fluids are cheap, parts are expensive. Preventative maintenance keeps machines running for a long time. Serviceability isn't considered as a priority during automotive design.
Thanks to you from Austria!!! I had a bad noise on my rear differential. Mechanic said: its gone, make new, 3200euro only material :-( . So i tried to change the oil. Good idea with timebelttool. Made it on my garage-pit. Needs about half an hour. Made it with 100ml syringe from hospital.
Fact: sucked out 420ml old oil, filled in 690ml new oil. So it was too less inside. No leaks on garbox. So ford flled too less...... Now the gearbox sounds better. Hope that it will help for a while.
great video. oddly enough, my standard Husky 3/8 ratchet fits in to remove the plug (tricky, but it def works). other than this, i did the same exact procedure as you (in fact, did it today BEFORE seeing your vid). i also made a little "dipstick" out of an aluminum fence tie to let me know where my fill level was. Did it on the ground and took about an hour. Another guy on here posted his, called "rear diff war" and cut his exhaust out, which is totally unneccesary. I also thought about drillling a hole in the rear member but opted not to as i didnt have to after all. thanks bro!!
Another excellent video.
The diff has a drain plug if you look at the front of it.
Harbor Freight sells a "Square Drive Socket Caps" set for 4.99. Includes 1/4, 3/8 and 1/2" drives. Use with open end, boxed in or ratcheting wrenches for tight spots.
That is great information. You are absolutely correct, FORD what were you thinking? My 2014 escape is the same set up. "I Decided" to drill a 3/8 hole directly back from the fill plug so that I could get a 3/8 extension through the rear cross member. I know most people will say DON'T drill through the crossmember but to get the plug out, suck and fill the rear, MUCH easier. You need to take care and measure carefully to get the hole in the correct place. It's my car and I hope to have it for a while. You are again absolutely correct about the PTU unit that MUST be changed more often. BTW I would love to see your idea about changing the trans fluid, Again thanks FORD for no dip stick. Take care
sounds like a good idea
Nice informative video. I have one question, does the friction plate part of diff to the front of the rear diff does it use the same fluid? I ask as normal diff oil doesn't contain anything for a lsd friction plates that it contains.
I had to go to 3 dealerships to find one that knew they could change the fluid.
The dealership that did the work actually lowered the diff to get to the fill port. Mine also has a drain plug.
My drain plug was a 5/16" Allen plug. I had to cut some off a standard Allen key to make it fit.
Thanks for this video. I need to do this on my 2014. I’m not looking forward to doing it because I’m in the 98% that will be working on the ground. Lol. Outside in the driveway at that. Waiting on nice weather. I’ve done the front differential oil change after watching your video on that. That turned out ok. Hopefully the rear will go smoothly as well.
Good luck!
Take a look at my comment above Rob, it may make the job a little easier. Good luck.
Hi, any chance you can you make a video on adjusting a loose hand brake? Can't find any videos on it on a 2014 escape. Thanks for all your videos.
READ THIS FOR TIME SAVING...
First off if you have a 2013 the fill plug probably does not use a square 3/8" driver for removal but rather an 8mm hex key. A 5/16 hex key (7.93mm) may work but you risk rounding (stripping) it and making the removal even more difficult. You can try to cut down the 8mm hex key to fit or follow the instructions below to make the whole process easier.
For 2013 and up model years the suggestion to remove the mounting bolts to raise the rear differential is actually a very easy process. The rear of the differential is mounted to a bracket and the bracket is attached to the frame. Do not remove the 4 bolts (2 on each side) holding the differential to the bracket. Instead the bracket will be detached from the frame crossmember instead as follows. Looking from the rear of the vehicle above the diff you will see 2 round mounting assemblies that attach the diff bracket. Remove the T55 bolts from the rear from each of those assemblies - very easy to do and the bolts should come out without a lot of effort. These insulated supports have rubber in the center to isolate noise etc from the diff. The diff will move very little with these 2 bolts removed since the front part of the diff assembly has another pair of these round mounting supports - do not touch those! Now with a jack under the rear of the diff you can jack up the read of the diff and it will pivot upwards even with the front part still attached to the isolating mounts. Jack it up only enough so that you can get an 8mm hex socket or 3/8" (based on your year) into the fill plug. but first CLEAN the plug with a wire brush to remove any rust and dirt so that the socket fully inserts into the plug to prevent stripping it.
Remove plug and clean all metal shavings from the strong magnet. I used a HFreight air suction brake bleeder to remove the old oil. As mentioned by others, you need to use a smaller more rigid clear or transparent hose (12" at least) pushed into the end of the HF hose since it is hard to feed the hose down into the case. With a little trial and error you can feed it down past the races/gears. I used a 2HP 4 gallon compressor and it did suck out the oil but it takes a while. It is a slow process so give the compression time to cool every so often. I spend 15 minutes and in the end I removed exactly 16 ounches of oil and could not get any more out. The case seemed to be dry at this point. With a clear hose at the top of the case you can tell when you are pulling just air or oil. Keep moving the hose around and try for more oil once it seems like you are ony pulling air out. It is a VERY slow process so you may be pulling out oil slowly even if you think you are not!. I refilled when finished with just over a quart of gear oil. I then lowered the diff and some fluid came out quickly until the level was at the bottom of the fill plug. When it was just dripping I raised the diff again, cleaned it and installed the fill plug with joint sealant. I then lowered the diff off the jack. With the diff off the jack it tends to rest right aound the height it needs to be to re-install the cleaned rear T55 bolts. You may have to move the diff a little by hand to get the bolts started (i put a little blue loctite on them). Make sure they go in clean without stripping any thread. I bolted them fairly snug but did not look up the torque specs for them. If your car is an old northern car like mine (2013) there is a LOT of rust on all the metal frame parts! Wear glasses or you will get rust in your eyes! I spend the morning doing this and cleaning up some of the rusted parts - will paint them next. Foreign car manufacturers definitely use more and better anti-corrosion materials on their metal parts!
By the way...my car had 83K miles and the fluid was very black, jet black (not amber) but still runny like new fluid and no large metal filings but a very noticeable black mass on the magnet.
Hope repair geek pins this for others in my position. Wasn't 3/8 drive for me, belt tool didn't help. I removed the 2 rear torx mounting the diff and jacked it up for access. I think it's actually probably easier this was anyway. If you have this same issue, just do what I did. Much easier than drilling the frame like others have done
Yours seems to be the best method, straightforward as it sounds?
@@neilcrompton1386 it was very easy once I got to it. granted technically you're not filling a tilted differential so it'll technically be a little under full I suppose
Thanks Willy, I will be attempting to access the plug on ramps so will these 2 Torx be accessible. I can't see them in his video.
@@neilcrompton1386 I'm sorry man work and then it's snowing so I had to clear my drive. far as I remember they should be accessible on ramps. problem I can foresee is that they're locktite in and leverage might be an issue on the ground like like that. plus I didn't have the same fastener for the fill hole so idk if they all had torx for those 2 bolts. whatever the case I'm talking about 2 bolts that support the rear of the differential. if you can get those out you can jack the diff up enough to fill it
edit, when I did it it was on a lift and for a customer. I don't remember everything as this was a year ago. I hope my input helps you and definitely glad if it does
Good job
Thank you!
I drilled the bottom, tapped it and fitted a magnetic drain plug right on the white sticker. The case is plenty thick enough to tap. Lock wired it to make sure it won’t come undone . Makes the next oil change a 10 minute job
Got a video link?
This is what i was thinking of doing but not knowing the inside I was hesitant. thanks for the info.
Check out "2013-2019 ford escape rear diffential cover modification"
Hi dear , m from Malaysia ,driving Kuga 2013 1.6T . I notice there is vibration noise coming from rear bottom when i turn corner at stand still or low speed (
Is the differential spinning constantly?, or do they stop at speed 25 miles
Good info for my Kuga. (European name) will use your guidance.
Mine has one of those QR code stickers on it. If that sticker was half the size it is a drain plug would fit perfectly. But ford also says that the rear diff fluid is good for life.
I would love to see this service on a 2021-2022 Bronco Sport both the PTU and the RDU.
Your rear diff looks like my rear diff in my '13 MKZ 3.7 AWD. However, mine has all kinds of obstructions just inside that plug. Took over an hour of fishing the hose around to get it to start sucking anything. I used the same sucker you have and only got enough out to fill it half way. Truth... how long did you fish that hose around?
can you do a transmission fluid video?
I scheduled this rear diff fluid change on my 2017 Escape at a Ford dealer, no problem right? When I dropped the vehicle off they didn’t do the job, the dealers service department said the fill plug wouldn’t come out in spite of soaking it with penetrating fluid and they didn’t want to crack the diff case. They recommended I take it to a third party transmission shop. I took it home, jacked it up and took the diff skid plate off which obviously had never been removed as the bolts were still undisturbed. The fill plug wasn’t soaked in fluid and hadn’t been disturbed. I did the job myself and then called the head of the Ford Service department and called him on their flat out lie. Of course he had to check into it, when he got back to me he had no excuse except to lamely tell me they should have told me that ‘if they had tried to do the job’ it would have been difficult. To my knowledge I’ve never had a Ford service department tell a bald faced lie like that before.
You must not have much experience with Ford service departments then lol
Still waiting for your mystery undercoating update. Stay safe Bro.
Soon.
Drill and tap a 1/8npt hole in the rear bottom off the diff near the left rear of the qr code sticker. You now have a drain plug hole. Install a 1/8npt plug with some Teflon tape on the threads. Merry Xmas
Good idea but given the fact you are going to do it at 100,000 miles, is it worth it?
@@comesthru yes most ppl dont even know what diff oil is. Being i am a licensed mechanic, i know better and change mine every 30,000km. Alot of ppl dont understand if you live anywhere cold, or if you drive your car like you stole it, OR BOTH* you are on a severe service scedule, that means cut all your service milage's down by 30-40%. More throttle means more sheer effect on the oil, more cold means condensation from thermal cycling which spoils the oil. Simple things with simple solutions... change the damn oil more often ;)
Is it OK to put Motul Gear Race oil in PTU and rear differential gradation 75w-140? I presume it far better then 80w-90. I live in Europe, climate should be appropriate.
Ford never stops amaze me. Because a drain plug and a bit more clearance for the filling plug would have been too much to as to Ford engineers
Planned obsolescence = "lifetime" fluids
I haven't gotten in there to change this yet - DREADING doing it, Im a pretty big guy and am gonna be doing it on the garage floor.
Have you seen the 3/8 T-bar flex ratchet at Harbor Freight? It looks pretty skinny and may get up in at that weird angle?
I bought a serpatine tool and bent in half. Afraid it would snap, but it didn't thank goodness. The hardest part for me was extracting the oil. Mine was much dirtier at 105k miles, that a small silicon tube had trouble sucking the dirty oil, and bigger silicon tubes can be orientated to fit into the hole. I was able to remove about 1/4 qrt, and then I did the process again the next day after driving 100 miles.
Is the awd 2016 fusion the same way
thanks hav the belt tool so easy?trying to shave a 3 eights ratchet end to use also???
so shave the end of a ratchet and voila clearance enough to remove and reassemble JPG
I wonder if it would affect that crossmember strength much just to drill like a 1" hole thorough it where that plug is to access it from the back with an extension. Sure would be alot easier.
I wondered the same thing.
i bought a 3/4 titanium bit to do just that, but in the end didnt need to... but, its not a bad idea.
There are 2 “plugs” in my 2017 escape 2.0 One faces the rear, the other faces to the drivers side. The drivers facing one (40 torx) is a little lower than the one facing rearward (3/8” square). It would make sense the lower one is for draining. So the rear facing one is the quantity level?
I've never changed the fluid in the rear diff of an Escape and if what you say is accurate (that your 2017 has a lower drain plug), usually the higher plug is the one to use for filling when changing the fluid for a transmission, so to me it would make sense that you use the higher plug for the fill of the rear diff. Word of caution though, before you loosen the lower plug, make sure you loosen and remove the higher one FIRST. You don't want to remove the lower one only to discover that you can't refill the rear diff via the higher plug if you can't get it off.
I own one of these, but for my next car what would you recommend purchasing? Looking at either sedan or truck.
how many liters are needed..??
How do you replace the rear diff gasket does the axle need to be dropped
Same problem with mine...can see the gasket hanging on the very bottom
How much did you end up putting in?
After a couple hours of research I was all ready to go but my 2013 SEL has a allen head for the fill plug not a 3/8 ratchet plug. This just escalated the pain in the ass level for my rear differential fluid change excursion. They must have changed the plug in 2014.
The only thing I would of done besides is to pour the extracted fluid back in the bottle that it is filled from to see if it came close to same amount taken from unit... other wise, good tip
I made a special tool to fit the 3/8th fill plug but upon inspection the plug on my 2013 rear diff has a torque hole in it!
Ended up drilling a hole through the cross member. It worked out great as it was much easier to snake a hose in the fill hole.
I put 5 litter transmission fluid , level my car and start the engine and open the drain plug but after 10 minutes no fluid came out. When I stop the engine then fluid come out . I checked all video but every video shows after engine start then fluid come out. Now the question which is right ?
Fluid is filled from the top via the air vent. With the engine running NO fluid will come out of the side port near the drivers axle shaft. With the engine not running fluid will come out of the side port.
The good news is in 2020 they made it very easy, but the special oil is $35/qt.
hand vacuum pump, use a stiff hose to jam to the bottom.
I know it been 3 years since this video was posted. I just changed my rear differential oil change 100,000 miles. And I would like to know how much oil you got from your suction can during you rear differential change.
I got 25 oz of old oil. I could not drain anymore. I would like to know how much.
Thanks
Doing the same thing on my 2018 EcoSport (rear carrier identical to the Escape) and I was going to ask the same question. I removed as much as I could, and was back up to the fill line before i used a quart, it was closer to 26oz. He did say in the beginning ford spec is 1.1 qt.
@@siryoink4644
Thank you so much. The book say 2.0 qt. I started to worry, if I got enough of the oil from the rear differential. I got exactly 26oz.
Again thanks
I have 2013 escape bought it with 16k has 134k never changed transmission fluid so I leave it or change it
How you doing mr. Man I have to tell you right now I need some help with my Mustang 4.6 L it's a 96 my mechanic said that cylinder number 3 and cylinder number 5 or down but it seems to me cylinder number 3 and cylinder number 5 should be on the driver's side but the cylinders that aren't running seem to be on the passenger side which I thought were one through four that's how I have the plugs wired and I know that you can go the other way I've seen lots of stuff on that but is the number one plug on a Mustang on the driver side or the passenger side in the front I have to ask you what's your opinion on this because it's running a lot better especially since I got it back from my mechanic and put the spark plug wires back on the spark plugs right I mean clip them in anyway and he's telling me I got to change the head this is Matt and I have a erect one that I can get all kinds of Parts off of so I'm trying to think to myself was he's really trying to make money off of me what would your suggestion before my problem he said he did a wet test on 4 compression on all cylinders and he said number 5 and number 7 had nothing but he also told me before that when I was working on myself that that particular motor with computer it actually sends a signal the number 7 and somehow the signal goes from 7 to 5 even though 5 is firing first I can't remember the terminology for that I didn't write do you have any advice for me I really appreciate it it seems to be running a lot better I put a few cans of steals all in the water and oil and I've gained some horsepower back that way. I was hoping you might be able to give me some advice I had heard one point time in some of my studies at number 7 always has a problem but I don't know what that is at any rate I appreciate your time thank you for your due diligence logic reason and Sensibility in all of your mechanic work and I am a study of mechanical engineering I was an apprentice at a machine shop for three and a half years I was so Advanced they put me in the inspection room and had me calibrating tools and running the coordinate measuring machine and going out and telling the boys that were there for 25 years how to adjust how to adjust your machines but what they needed to do to make the adjustments to get it into tolerance I was driven out shortly after this but we know at this point that there can only be so many Alphas in one room at one time LOL and I'm sorry about the talk-to-text I'm not going to go back and edit it because with this device close enough is close enough thank you sir any advice would be appreciated for my 96 Mustang 4.6 liter
Dude I freaking hate these new vehicles. I got a 2014 1.6l ford escape NON-Awd...... Do I have a front differential or what? Is the front differential integrated with the transmission??? I want to drain and fill it but not a single video on doing the front diff. So I am stuck. Please help.
If you have the FWD version, the front differential is integrated with the transmission, therefore you only have to only service your transmission.
If you had AWD then you would have a rear differential like the one in the video.
Brent is correct, though the PTU on the AWD has its own fluid.
Is this service only for AWD Ford Escapes?
Yes
Meanwhile , pull into a jiffy lube or oil change place and they say according to ford, its time to change your differential fluid lol
One of the many reasons I traded mine in for a Grand Cherokee
lol I went opposite years ago then back but still have both now
You took synthetic oil out and put regular back in which given the $5-8 difference in cost makes no sense to me. Synthetic is always the best choice.
i wish i had you as a neighbor! can you do this for my car?
Took me like 30 minutes total on the ground lol
Its shameful that vehicle manufacturers design things this way. Lifetime fluid my ass! I know its becoming the new trend but it definitely influences my vehicle purchasing decisions. I wouldn't take a German car as a gift for this reason. They seem to take pleasure in making things difficult to work on!!
mig weld a nut on it and use a extra long flex ratchet wrench .....Or Not
A mig gun isn't going to fit into that spot. Even if it did, you'd back the nut out right into the crossmember. It's that close.
@@RepairGeek i was more talking about after the fact its off lol
You have to take into account that these cars are mostly sold in the rust belt and fall apart from road salts and the engineers are from the same part of the country so 5 year reliability is not an issue to them.
Here on the west coast where we don't like salty ice cream cones we have to endure the cheap engineering these big three throw at us.
Who can afford 60,000 dollars every 5 or 6 years to replace a rust bucket, Ford has at least tried to address the issue with aluminizeing some of there stuff
There is a drain plug.....
So I'm about 8 minutes 50 seconds and you're talking about the 80 90 gear weight oil the Ford recommends. I had an 8 in B flathead Ford 4 cylinder tractor and it has a giant transmission case in it and when I have started looking that up the suggestions were popping out for the 9 and be at 80 90 weight by the 8th and B it said something about mineral oil so do you suppose that mineral oil could also be used in that place and then also the belt to let your using forever but it's working on the ground. I would think backing it up on a set of ramps would cure that problem because I was watching on do the Lefty Lucy plug that ranch didn't come much below the bottom of the tire so I would think just a pair of ramps or a Jack would do it. The low profile wrench profile Ranch wow what a great idea. I do talk to text so I'm not going to correct the profile Ranch comment because it's extra funny LOL it's amazing what technology here's a saying and interprets no connotation whatsoever
Ford told me 100k miles
I find it totally infuriating that there’s not a drain and fill plug in Ford’s infinite wisdom that they don’t put it in an accessible location and don’t even get me started about the ptu…. I think after my experience with the Ford escape this will be the last Ford I ever purchased
Dig around in this comments section and you actually find one of the engineers that designed this differential trying to defend the lack of a drain plug!
@@RepairGeek There is no defending it. Even if were good to 100K miles it still should have accessible drain and fill ports. That's just poor engineering and sub-standard designing. If those engineers worked for me they would be fired or demoted.
Too bad Ford doesn't care enough I'm it's production value to create the diff for serviceability.
Leave it to ford
I worked on this differential. You don't need to change the oil. It's good for about 200K miles or more. You're wasting your time, money, and energy doing this at 72000 miles. You're also using the wrong oil. If anything, you just reduced your bearing and gear durability significantly.
Yes, just like the fluid in the PTU's. You guys called that stuff lifetime as well. So, you can see my skepticism. Whatever it takes to keep that cost of ownership down right? I'm sorry, I'd rather waste $7 dollars worth of fluid than waste $1000 on a new diff.
Most axles are serviceable, but this one isn't. I don't work on PTU's, but there's a big difference. This is a part time disconnecting axle, so 90's of the time it's spinning unloaded. At 72K miles, it should brand new on the inside. The only early failures you might have is if the axle was built and the components were somehow contaminated. That's the primary failure mode that we've seen (I don't work at Ford, but at a supplier). When you change the oil you have to be extra careful about introducing particles that don't belong in there. But what do I know... I'm just someone who worked on almost every axle in north America... Not just Ford.
@@Makketronix exactly! "It should be brand new on the inside" but, you don't know the condition of the diff until it makes noise (and it's shot at that point) or you do a service as preventive maintenance.
@@RepairGeek in your case unnecessary preventive maintenance at 72000 miles.
@@Makketronix absolutely but, if I wouldn't have done the service, I wouldn't have known. Going back to my original point: I'd rather waste $7 dollars worth of fluid than waste $1000 on a new diff.
thats a plug not a bolt just sayin lol
u think this is bad? wait til u gotta change the water pump !! might be easier changing the engine , no joke. i did it. I WILL NEVER BUY ANOTHER NEW FORD EVER IF I CAN HELP IT !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Amazing - you've got a lift and some tools but not enough sense to use some eye protection. You'd set a much better example if you did.
Lol
Thanks mommy!
I did mine on the ground. Took me half an hour and used a cut down cheap serpentine tool to undo plug. It’s not a big job at all.