On my channel i have an updated frame they hopefully get out soon. It fixed the slide moving. Gapd for takedown is still big to accommodate any lever and they wont change that
@huskyarmory that's good, it seems to be a confusion on things and in the end it's on manufacturing. I got an email saying take down a video because I'm confusing people so I just took down all of them.
The slide release spring is supposed to sit below the first pin it shouldn’t come into contact with the locking block it could cause failure to go fully into battery issues other then that great video
the gen 1 is junk that does not make me a Bozo,cosue i dont want to rely on a shim to keep my slide lock in place & 7 p80s run like champs i would bet my life on,they dont stand behind there products ,nothing more then a toy is all i have seen i requested a gen2 replacement & got no reponce from qeisler & 7 emails later ,i am ready to tell people dont bet your life on qeisler built not bought
To bad it’s not that easy. Only problem (so far) that I’ve had with my build is the take down lever is being pressed down by the slide and when I pull the trigger the slide comes right off
If you never solved this issue on my frames I recieved from them, I had to sand down the ramp infront of the trigger hole that is behind the slide stop takedown lever. It was partially covering the groove in that lever which is what causes this issue. I ordered 2 frames and had this issue with both. Once you take that ramp down some it will solve the issue. It can be a bit of a hassle but not too bad. If you still need help I can get in touch with you and give you some other platform info to actually show you. On my p80 frames they don't even have that ramp that is kinda how I figured out the fix tothe issue. However oem glock frames do, so rather than removing it fully I just took it down some so the top of it is below that groove.
@@Htx_GHOST713 so they sent me an updated frame and I wish they would get them sent out. They are behind schedule but the internal walls are higher and no slop when the trigger is pulled. Have a video on it
First 2 minutes in. Can’t see squat. Waste of time. You’re welcome for the comment/ interaction. It’s worth more to you than the video is to the public.
You forgot the slide hold latching lever now you have to disassemble the rail and locking block watch a install video and then you can teach everyone how not to forget a important part unless you’re ghetto and don’t need that function on your 80% that is now a 97 %
If anyone is having any issues with their build I like to help others and will give you my two cents haha just reply to this comment with any issues you may be experiencing and I’ll get back to you
@@Sickiest3rd could be a safety plunger issue the vertical extension on the trigger bar has to disengage the safety plunger for the firing pin to to come through the breach face. Or maybe you’re having engagement issues please provide more information on what’s happening
Hey man, I’ve seen many people say it’s normal for it to just sit a tiny bit high because that’s how they were designed that’s what I heard but don’t count my word for it but what people from Reddit said, I’m finishing my build later this week, I’ll let you know if mine does the same.
Alright I think the spring is just an extra that came with the kit as I believe the bigger L shape is for Glock 17 slide lock and the smaller is for Glock 19. As far as the trigger, I’m pretty sure the spring is backwards. It should make an S when looking at it from the right side, not a backwards S
@@LathenBlissit idk. I'm pretty sure they're mostly identical. Just make sure it's for a compact frame. Make sure the trigger spring is for a Glock 19 btw. Z
U don't want thar frame . My buddy got it and noticed it was made in a garbage cou try so he tossed it immediately destroying it making sure no one has to suffer with it. Get urself a dood 'ol american p80 or psa dagger there better quality and made here.🇺🇸🇺🇸🇺🇸🇺🇸🇺🇲🇺🇲🇺🇲
Their frames are much better than oem and p80 and gst-9 frames imo. Does take a little more know how than gst9 and p80 but definitely worth it. A trick to the mag release lever is get it inserted into its pocket in the front of the grip. After you gently let it rest in there don't force it, stick a finger thru the bottom of the grip where you can use a finger to stop the spring from falling out when you tilt the frame backwards. While having it in this position slide the mag release lever in then grab your punch and use it to pry your spring over to slip into the groove for it on the inside of the mag release lever.
@@pepepantuflas1 psa doesn't make 80s and p80 screwed over their good old country buy selling frames and not shipping. Almost a year now and they don't have any frames coming out
Just buy extended slide stop levers. I put them on all my glocks bc I got big hands and big fingers so grabbing them Fuckers when they are oem spec is almost impossible. But with extended ones the ends stick out more than enough to grab easily but not too much to be sore to the eye
You made this video, yet you do NOT offer the kit you're using on your site. The link is associated with a lesser product. Your search bar is completely ineffective. 👎
Get 10% off your Geisler 19x Frame code "STAYFROSTY" huskyarmory.com/80-frames
@@huskyarmory what magwells fit the 19x model yall make I can't find not a single thing of info for it
@huskyarmory What Lower parts kit Goes , with the Geisler 19x Frame ? Is it the 19 or the 17 Lpk ?
@@DedeJames-o2q 17
17 lpk 17 mag
@@justonmartin634 thanks man I appreciate that I needed to know , finna order one
On my channel i have an updated frame they hopefully get out soon. It fixed the slide moving. Gapd for takedown is still big to accommodate any lever and they wont change that
We have only Gen. 2 frames now!
@huskyarmory that's good, it seems to be a confusion on things and in the end it's on manufacturing. I got an email saying take down a video because I'm confusing people so I just took down all of them.
How did you fix the slide creep?
@@Sheeshuonmydik new guide rod 18 lbs at least
@@Sheeshuonmydik get a gen 2
Thank you boss I needed that walk through
Looks pretty clean! Love to see a frame stripped down bare bones..... thanks for sharing. Just sub’d
The slide release spring is supposed to sit below the first pin it shouldn’t come into contact with the locking block it could cause failure to go fully into battery issues other then that great video
Great video and very helpful. Ignore the bozos criticizing it.
Thanks 👍
the gen 1 is junk that does not make me a Bozo,cosue i dont want to rely on a shim to keep my slide lock in place & 7 p80s run like champs i would bet my life on,they dont stand behind there products ,nothing more then a toy is all i have seen i requested a gen2 replacement & got no reponce from qeisler & 7 emails later ,i am ready to tell people dont bet your life on qeisler built not bought
Is that a 17 slide? Can the frame use a 17 slide ?
I just got one not to long ago I was wondering what flared magwell will it accept
To bad it’s not that easy. Only problem (so far) that I’ve had with my build is the take down lever is being pressed down by the slide and when I pull the trigger the slide comes right off
If you never solved this issue on my frames I recieved from them, I had to sand down the ramp infront of the trigger hole that is behind the slide stop takedown lever. It was partially covering the groove in that lever which is what causes this issue. I ordered 2 frames and had this issue with both. Once you take that ramp down some it will solve the issue. It can be a bit of a hassle but not too bad. If you still need help I can get in touch with you and give you some other platform info to actually show you. On my p80 frames they don't even have that ramp that is kinda how I figured out the fix tothe issue. However oem glock frames do, so rather than removing it fully I just took it down some so the top of it is below that groove.
@@Htx_GHOST713 so they sent me an updated frame and I wish they would get them sent out. They are behind schedule but the internal walls are higher and no slop when the trigger is pulled. Have a video on it
@@Htx_GHOST713can we get in Touch I have a couple of questions about my Geisler even videos at the range
Why mine don’t shoot I added a dagger slide, I build my frame watching dis video
First 2 minutes in. Can’t see squat. Waste of time. You’re welcome for the comment/ interaction. It’s worth more to you than the video is to the public.
You forgot the slide hold latching lever now you have to disassemble the rail and locking block watch a install video and then you can teach everyone how not to forget a important part unless you’re ghetto and don’t need that function on your 80% that is now a 97 %
Hahaha
Wtf are you talking about ?
Stoltenberg Falls
So.. what you mentioned in another comment is that you basically need the G17 lower parts kit from Husky that has the longer slide lock spring?
Correct
If anyone is having any issues with their build I like to help others and will give you my two cents haha just reply to this comment with any issues you may be experiencing and I’ll get back to you
Mine won’t shoot I tryed to shoot it with a dagger slide
@@Sickiest3rd could be a safety plunger issue the vertical extension on the trigger bar has to disengage the safety plunger for the firing pin to to come through the breach face. Or maybe you’re having engagement issues please provide more information on what’s happening
Douglas Hollow
Any Glock 19 slide will fit right in
correct any Glock 19 Gen. 3
They are real
Can you put a gen 5 slide on the frame since the 19x is in the gen 5 family ?
This is a gen 3. If you can put a gen 5 on a gen 3 then yes. If not then no
Possibly w/ an adapter / get 3 recoil conversion spring.
Can you please tell us how you got the frame to almost sit flush? Got one of your kits and the slide sits way too high.
Hey man, I’ve seen many people say it’s normal for it to just sit a tiny bit high because that’s how they were designed that’s what I heard but don’t count my word for it but what people from Reddit said, I’m finishing my build later this week, I’ll let you know if mine does the same.
I have an extra L shaped spring sort of thing that came in my lower kit. Idk wtf it is. And my trigger isnt resetting
Alright I think the spring is just an extra that came with the kit as I believe the bigger L shape is for Glock 17 slide lock and the smaller is for Glock 19. As far as the trigger, I’m pretty sure the spring is backwards. It should make an S when looking at it from the right side, not a backwards S
@@TimboTactical ty buddy
@@TimboTactical you were right! Thank you bud!
When you get the frame do you need to do anything to it? Or you can just start building
Use da jig
@@Sickiest3rdhow 🤦🏾♂️
@huskyarmory how can i Turn it into a Glock 23 ? What all parts do I need for the lower ?
I want to know to
what dust cap does this take?
Also wondering if magpul mags could be the reason it jams and light strikes
dust cap? Sounds like an ammo or slide issue, not a mag.
Adrain Alley
Does anyone know y mine isn’t racking a round? It hits the barrel when I try to put one up but goes smooth with no mag
Your slide release spring is supposed to be below the top pin the spring shouldn’t be in contact with the locking block this could cause some issues
Bro so what Lower part kit would I need too buy for the 19x build? Laik a 17?
19 or 17 gen 3 I went with a 19 gen 3. Works fine.
@@finnanutyo1153can I do 23?
@@LathenBlissit idk. I'm pretty sure they're mostly identical. Just make sure it's for a compact frame. Make sure the trigger spring is for a Glock 19 btw. Z
@@finnanutyo1153what magwell?
@@LathenBlissityes
Video isn’t so helpful. Can u show closer exactly where ur putting stuff. Especially the spring for the release.
U don't want thar frame . My buddy got it and noticed it was made in a garbage cou try so he tossed it immediately destroying it making sure no one has to suffer with it. Get urself a dood 'ol american p80 or psa dagger there better quality and made here.🇺🇸🇺🇸🇺🇸🇺🇸🇺🇲🇺🇲🇺🇲
It's a good frame if you know how to build
Their frames are much better than oem and p80 and gst-9 frames imo. Does take a little more know how than gst9 and p80 but definitely worth it. A trick to the mag release lever is get it inserted into its pocket in the front of the grip. After you gently let it rest in there don't force it, stick a finger thru the bottom of the grip where you can use a finger to stop the spring from falling out when you tilt the frame backwards. While having it in this position slide the mag release lever in then grab your punch and use it to pry your spring over to slip into the groove for it on the inside of the mag release lever.
@@pepepantuflas1 psa doesn't make 80s and p80 screwed over their good old country buy selling frames and not shipping. Almost a year now and they don't have any frames coming out
@@yeks1491the fact he says it's trash because it's from Israel is pretty funny
Dorthy Meadows
Any way you guys can check if you received my order ?
Did u get your order bro
Does your lower parts kit have a thicker slide lock than the Glock oem version?
Glock stores is I believe
yep
Sorry do these take glock OEM mags.
Yes, they do!
Make sure it’s a 17 don’t make the mistake I made due to it have a g17 grip length g19 mags will not work
Does a Glock 19 gen 3 trigger assembly fit in that 19x upper?
Yep, the only difference is the slide lock spring which is the Glock 17 version (a bit longer).
@@huskyarmory ah… ok. Thank you.
I’m having issues with the trigger, it’s a 19 gen 3 lower
Yes it will
@huskyarmory I did make a comment at the top as well. So do you need the g17 lpk that has the longer slide lock spring?
What lower part kit is that and does a glock 19 gen 3 lower part kit fits it?
It’s not a 19 its a hybrid of the 17x and 19x
@@LathenBlissitso question when you have a 19x what lower parts kit do you put inside of it??
@@Splxtttem u can put g19x our 23x same with the slide but for the magizne u need a 17 magazine if u build the 19 our if build the 23 u need a 22 mag
Is this a real website?
yea they legit
anyone make a thicker slide lock? the slide lock hole is a little out of spec.
Yeah I messed up on my damn holes because the holes on the pieces don’t even line up :/
I made one out of thicker steel! Looks and works better!
Just buy extended slide stop levers. I put them on all my glocks bc I got big hands and big fingers so grabbing them Fuckers when they are oem spec is almost impossible. But with extended ones the ends stick out more than enough to grab easily but not too much to be sore to the eye
@@Htx_GHOST713 people want thicker
Any one order from that site before
We have been around for a year and are one of the biggest Geisler dealers. Feel free to reach out with any ufrther questions!
does husky armory require ffl for frame
@@nunyabusiness776 which other sites have them in stock with no ffl
@@elelouisy1372you ever found a site?
@@mrrackies5666there ain’t any! That what makes it very confusing that they’re the only ones selling it
We have them
I have a brown one
You made this video, yet you do NOT offer the kit you're using on your site. The link is associated with a lesser product. Your search bar is completely ineffective. 👎
It's outta stock I ordered the last one
Did you get your order ?
The only reason i clicked was because i misread the first world ans guiessle