Wrench, thank you very much for taking the time to make and post this video. Been wanting to replace a Fog Light on my Daughters Mazda 6 for about 6 months now. For me it was easier to just pull the Bumper like in your video. I had complete access in 15 minutes as I wanted to time myself. Plus it gives me access to clean up the front end of the car inside and out. Keep up the great work Brother.
You are a life saver! I watched the bumper video and the headlight removal videos and I couldn't have done it without them. I must say, your video must have been taken not long after you got the video, because half of my bolts were so rusted they either broke or just wouldn't come out. Nevertheless, thanks for posting the videos!
One of the advantages to living where it does not snow :). That and the fact that the car in the video is 6 years old. Glad you found the video helpful.
My mom reversed into my speed6 and I had it repaired in a body shop. They forgot to connect the headlight plug. Thanks to your videos I was able to fix the problem without getting ripped off at pep boys!
A few notes for this video: 1. You DO NOT need to drop the bumper. Most people with normal sized hands should be able to reach the low beam cap and disconnect the bulb. 2. The bulb for the low beam is an A1 bulb. It should be very common at your local auto store.
HAH this is absolutely not true regarding the 2008 with v6 and HID bulb. Its of incredibl,y poor design, but that bumper and headlight housing has to come out
@Brodensson this video says headlight removal not bulb replacement. Read the description. Also, it very difficult to reach the fog light bulb and turn signal bulb without removing the headlight assembly. As someone who has large hands it is difficult to change bulbs other than the low beam bulb. The bulbs are H1 bulbs not A1.
@@rikanderson5951Yep that is all correct. I did the headlight replacement a few years ago successfully. I remember watching a video at the time and getting annoyed that I'd have to drop the whole bumper to get the bulbs out, but I was able to reach in and get them. I'm guessing I commented on the wrong video (and made a typo with A1).
@@rikanderson5951 99% sure I meant to comment on this video: "How to Replace Headlight Bulbs 02-07 Mazda 6" by 1A Auto. I'm guessing that's also why I mixed up the name of A1 and H1 bulbs. I feel I have to apologise to this channel owner!
Looks like a lot of people don't know what a headlight is because I'm always getting messages telling me that I don't need to take the bumper off to replace them. That is only true if you want to replace the headlight BULBS which is not what this video is about. This video shows you how to remove the headlight. If you don't know the difference between a headlight and a headlight bulb then do a google search for it.
Thank you for the tutorial. Finally did this yesterday, took me about 2 hours including uninstalling and reinstalling the bumper cover. Was unable to disconnect the headlight wiring harness for some reason so I just swiveled out the headlight far enough to change the HID light bulb - yes, on my 2006 that was what was installed. No clips on those though, just a twist ring so maybe easier. Overall thanks to your videos it wasn't difficult, just lots of steps. Be patient and take breaks when you need to and you'll be good.
Swapped out the low beams and fog lights in my 05 6S today with the help of your video. While it took a little time to take off the front bumper and put it back on, it made swapping out the bulbs a breeze rather than accessing through the wheel well.
great video! I recently bought new aftermarket headlight assemblies and bulbs and I'm experiencing hyper flashing with the turn signals on the new units, I'm not using any LEDs just regular bulbs that are brand new and I hooked the old assembly back up and those worked fine so it's definitely something going on in the new headlight assembly, the manufacturer is no help but said to just return it... any ideas?
hey dude really really thank you, the next week I'm going to replace my headlights and I didn't know where start, especially with the bumper this two video helped me a lot, maybe you can tell me after remove the cap of the headlight how I replace the bulb (pull it, turn it or what I need to do?) Thank you dude! happywrenching
Happywrenching, I have a Mazda 6, 2002 I want to replace the halogen headlights with Xeon headlights! Will that be a problem for the on-board computer or the wiring etc.? I would appreciate any advice...
Thank you so much I have an 06' Mazda 6 3.0 and I wanted to remove it but thought it had clips holding it on since Mazda seems to have tabs all over the place!!!! Also I have seen the bumper pull away at corner near headlights
Are all the bolts the same length? I replaced my headlight when the harness rotted out, with the help of your video I was able to complete the job in about an hour on my own. Thanks
The car in the video is 2006 from North America. As long as your Mazda 6 is a first generation then the steps in this video will work. If you have a second generation (came out in 2007 and 2009 for North America) then the steps will be different.
Very helpful video's. Now I have a question I have 08 Mazda 6 the park light bulbs need replacing. Do I have to pull out the headlight or can I just open the hood and simply replace parking light bulb? Sorry if this is a stupid question. Again your video are very helpful. Thanks for your time.
Hope you see this, been a while. I frayed the interior headlight ( not highbeam) wore when trying to put in a new bulb. Just replacing the headlight assembly will solve this issue as it is already wired, correct?
happywrenching, 2 questions... First, my low beams seem awful dim on my '05 Mazda 6 Sedan, the headlight lens are actually clear but I'm wanting to brighten my low beams with replacement bulbs, what would you recommend? Secondly, it looks like there are 4 bulb ports in these headlight systems, what is the port between the turn signal and the high beam port used for, are there supposed to be bulbs in there? I don't see that anything comes on in them, high or low. Thanks for all the Mazda videos too.
+txtpqb Might be too late, but the answer to your second question - the port between turn signal and high beam is actually an integrated fog light on models that don't have them down in the standard bumper location :D
Yes there is no need to remove the bumper to change the bulbs. This video is for those who are looking to remove the whole headlight assembly. I just showed the shot of the bulbs as an extra.
I have a Mazda 6 that I always park outside. Due the the oxidation it has also become foggy. I recommend doing a headlight restoration, which just sands off the oxidation and following up with a headlight sealer. It makes it look like new and it cheaper than replacing the headlight.
A good , patient headlight restoration will solve lots of ills. This can take up to 1-1/2 hours per side. A good headlight restoration kit, such as that sold by 3M, will set you back $15 to $20. You will need a small drill. Everything else is included. Be careful to take your time during each step. It’s well worth it and beats the heck out of removing the bumper and headlight assembly. Use a good sealer over the lens once you are done. This prolongs the time between restorations.
Greeting! I have 2 Mazdas 6 in the family, 2006/2007 GG, one long hatchback and one sedan. They are the same, but the hatchback has factory xenon. I am keep just one, I would like to move a set of front headlights with xenon to the sedan version. Is it possible without major obstacles?
Great Video - but it doesn't address what I was hoping to see which would be the install (or, more accurately, the adjustment of the newly installed headlight). Would you be able to do a video on adjusting the headlight height on a 2014 (or similar setup) Mazda3 (I have the S Touring) - It is more a gear type assembly than the screw adjustment like on older cars. Thanks if you can!
+rychendroll Won't be able to do a video since I don't have access to a Mazda3 at the moment. Hope you find the info somewhere else. Thanks for stopping by!
It's really stupid that we have to take the whole front end off of a modern car in order to replace headlamps. I just changed the low beam in my CX-7. It wasn't half as bad as this but what a mess it was compared to changing the sealed beam on my old '69 Pontiac. Whatever happened to cars that made sense? Shame on the myopic designers of these automotive nightmares! Thanks for posting.
Thanks for this. I think it sucks they make it so involved. Wish I had bought all new bulbs while I had it all apart. I did replace the low beams with halogens. It also sucks you can't buy just the front lens. It looks like it's only held on by a few clips. Would make life a lot simpler. Thanks again.
I have a 2006 Mazda 6s 3.0 and want to replace my headlamps, but I am given two choices a Standard and a Sporty. Do you know the difference? This is not the one that uses the Xenon bulbs. Mine uses the regular Halogen bulbs, but there's the Standard and the Sporty, I don't know the difference.
Sport and Grand Touring packages came with headlights and taillights that had black surrounds. Base models had clear surrounds. The car in the video is a 2006 6i w/ the sports package and if you look at the headlight you can see that the inside is tinted black.
Hi "Mr Happywrenching", thanks for your info. Would you please how to take out the light bulb (how to disconnect it... for sure is simple but I heard that we shouldn't touch the glass part with bare hands.
So there's no other way to replace the headlights besides taking the bumper off? Also I have an 08 Mazda 6i which doesn't have fog lights, but if I take the bumper off can I install the fog lights then also? Love the video btw! I'm a chic who's not super skilled with mechanics but hopefully can pull this off rather than bring to a dealer like my guy wants me to. :)
That's right, the bumper has to come off to take out the headlights. As for the fog lights, there are several more things you need to make it work such as the correct wiring harness and the switch - not an easy task, mostly because of the harness.
Does this video apply to the 2007 Mazda 6, as well? Also, how do I replace the plastic cover to the headlights? Mine is faded and dingy. I'd love to replace them as soon as possible. Thanks for the videos!! Since I just bought this 2007 Mazda 6, I subscribed to your channel. I can see it's going to be very useful. Thanks again.
Yes, this video applies to 2002 - 2008 Mazda 6. I'm not really sure what you mean by plastic cover. As far as I know the headlight is one unit - you cannot replace anything on it. Thanks for subscribing :)
What I meant by "plastic cover" is the clear piece that covers the actual lights, themselves. The outer piece. Mine has yellowed and is quite dingy. I hope I can replace them. However, if I have to actually replace the entire headlight system, I'll just have to live with them being yellowed and dingy, I guess. Thanks again.
Yeah, unfortunately that piece cannot be replaced - the whole headlamp must be swapped out. I'm in the same boat - even though I've cleaned and buffed them, over time the cover turn yellow again. Mine even fog up on the inside. Don't really want to spend $130 per lamp so I just live with it.
Okay. That makes sense. Well, I guess I'd better start saving up my money. Since I just purchased the car, and LOVE it!!!!, I don't want to deal with yellowed, dingy headlight covers just yet. :) Thanks for your help.
3M makes an excellent headlight restoration kit, available for $15-$20. If you are very patient, taking as much as 1-1/2 hours per side, you can eliminate those dingy, yellow headlights. It’s imperative that you take lots of time for each step. Tool needed: 3/8” electric drill. Also, some paper or microfiber towels.
Whenever i have to replace a headlight bulb on my 2003 madzza 6 i have my daughter do it for me since her hands are small and can actually fit inside the headlight assembly . There is no way my large male hands can do fit in there.
Do you happen to have a video on how to remove the fender off of the Mazda 6? Someone backed into mine and now I have to replace it, but I'm not sure how difficult it might be.
Unfortunately i don't have any videos on removing the fenders. However it is not difficult. You have to remove the three bolts on top of the fender. Remove the headlights and bumper and under that you will find one more bolt. There is one bolt under the cowl cover (which you have to remove to get at the bolt). Finally there are two bolts on the bottom of the fender. I may actually do a quick video on this.
thank mas i had to do this because the little light on the high bean fell inside ... hey do another video on how to change controll arms in the mazda 6 since is a common problem
look on the back of the headlight. you will see a small turn knob that is in line with the bulb. turn and pull that out.. its a long tube that comes out before you see the bulb. Takes 20 seconds to change a bulb from start to finish. Pause vid at 3:05. The light gray long tab looking knob is the one I am talking about.
You dont have to remove it all the way, Undo the top 10mm bolts and sides if theyre not already broken, slide the bumper forward and you should have room to work. If youre just replacing low beam bulbs I suggest just undoing the fender-wells and replace bulbs from there.
Turn the wheel inward on the side with the blown bulb, take off the 3 plastic screws and pull back the plastic barrier. Easy access to the headlight, 2 minute repair with no bumper removal. '04 Mazda 6
I am about to install myself new headlights in my Mazda 6. I recently cracked one by running into a mailbox lol...dont ask. But i would like to know if this Mazda 6 is a 2008??? NEED TO KNOW so I can disassemble correctly, please respond , and thank you!
I wish I would of seen this before taking mine to the body shop to replace both headlights. When I picked it up, now the HIGH beams turn on simultaneously with the regular/low beam bulbs. Why is it doing that now? Did they just accidentally switch the high beam and parking bulb connectors or what? I want to avoid taking it back to the shop if I can do it myself. Sorry I'm not car savvy.
Basically there are two sets of headlights for the first gen Mazda 6 - one set for years 2003 - 2005 and one set for years 2006 - 2008. The wiring is different between the two sets. The upgraded headlights that you are seeing for 03-06 will not work with your 07.
I swapped a fusion 2.3 engine when I first bought the car. That was at 98,000 miles on the odometer. It now has close to 170,000. Nothing but regular maintenance and the car is still going strong. I love mine as well.
At 2:00 minutes into the video you take a screw out of a white tab/clip do you know what that part is called mine broke n now I can't get the corner of the bumper to stay in thanks
That is the front bumper bracket - Mazda calls it a slide. Part number for the right side is - GJ6A50E11C and GJ6A50E12C for the left. They sell them on eBay for around 10 bucks. Of course you can also get it at a dealer.
Two things; 1) 2013 was 11 years ago... That's crazy! 2) Dropping the bumper?... Ridiculous! Mazda should be ashamed of themselves. I replaced my BMW headlamp buckets last year and all four bolts have specific access. Now I want to do my girlfriend's and it's going to be a bit of a project. At least I'll look like a hero. :)
What the absolute hell? Why do you have to disassemble the whole front end to replace a headlight in these cars? Does no one else think that's just crazy or am I just old?
8 years later AND still useful thanks !!! Just happened to need that for my poor Mazda
Thank you so much! People like you that make these videos are the real MVP. I was able to easily do what I needed thanks to these two videos.
Wrench, thank you very much for taking the time to make and post this video. Been wanting to replace a Fog Light on my Daughters Mazda 6 for about 6 months now. For me it was easier to just pull the Bumper like in your video. I had complete access in 15 minutes as I wanted to time myself. Plus it gives me access to clean up the front end of the car inside and out. Keep up the great work Brother.
Thank you so much for making this tutorial. My headlight was recently damage by a driver and this will save me thousands replacing it myself.
You are a life saver! I watched the bumper video and the headlight removal videos and I couldn't have done it without them. I must say, your video must have been taken not long after you got the video, because half of my bolts were so rusted they either broke or just wouldn't come out. Nevertheless, thanks for posting the videos!
One of the advantages to living where it does not snow :). That and the fact that the car in the video is 6 years old. Glad you found the video helpful.
My mom reversed into my speed6 and I had it repaired in a body shop. They forgot to connect the headlight plug. Thanks to your videos I was able to fix the problem without getting ripped off at pep boys!
Very thorough, thanks! Some times my Hanes manual simply doesn't go into enough detail so this video helped clear up some confusion!
Really good tutorial, clear explanation of where to find each bolt/screw, and what tools to use. :) thanks!
Love your work mate. Keep it up. So helpful... And you don't drag on like other people do and the camera is still.
A few notes for this video:
1. You DO NOT need to drop the bumper. Most people with normal sized hands should be able to reach the low beam cap and disconnect the bulb.
2. The bulb for the low beam is an A1 bulb. It should be very common at your local auto store.
HAH this is absolutely not true regarding the 2008 with v6 and HID bulb. Its of incredibl,y poor design, but that bumper and headlight housing has to come out
@Brodensson this video says headlight removal not bulb replacement. Read the description. Also, it very difficult to reach the fog light bulb and turn signal bulb without removing the headlight assembly. As someone who has large hands it is difficult to change bulbs other than the low beam bulb. The bulbs are H1 bulbs not A1.
@@rikanderson5951Yep that is all correct.
I did the headlight replacement a few years ago successfully. I remember watching a video at the time and getting annoyed that I'd have to drop the whole bumper to get the bulbs out, but I was able to reach in and get them. I'm guessing I commented on the wrong video (and made a typo with A1).
@@rikanderson5951 99% sure I meant to comment on this video:
"How to Replace Headlight Bulbs 02-07 Mazda 6" by 1A Auto. I'm guessing that's also why I mixed up the name of A1 and H1 bulbs. I feel I have to apologise to this channel owner!
Thanks mate your a life saver did this whole process today just to change one dead bulb... So I did that lot using this guide saved my life :)
Looks like a lot of people don't know what a headlight is because I'm always getting messages telling me that I don't need to take the bumper off to replace them. That is only true if you want to replace the headlight BULBS which is not what this video is about. This video shows you how to remove the headlight. If you don't know the difference between a headlight and a headlight bulb then do a google search for it.
hi,how do the fog works,coz my car does not have provision of them from the inside?
It have indicators,nomarl beams and high beams only.
happywrenching I think people are getting confused with this video. People, this is a headlight replacement, not headlight BULB.
I think some people know it as headlight housing.
happywrenching either way, this was extremely helpful, thanks dude.
happywrenching I'm having a problem changing out my headlights bulbs. How would i do that its so hard to get to.
Thank you for the tutorial. Finally did this yesterday, took me about 2 hours including uninstalling and reinstalling the bumper cover. Was unable to disconnect the headlight wiring harness for some reason so I just swiveled out the headlight far enough to change the HID light bulb - yes, on my 2006 that was what was installed. No clips on those though, just a twist ring so maybe easier.
Overall thanks to your videos it wasn't difficult, just lots of steps. Be patient and take breaks when you need to and you'll be good.
Swapped out the low beams and fog lights in my 05 6S today with the help of your video. While it took a little time to take off the front bumper and put it back on, it made swapping out the bulbs a breeze rather than accessing through the wheel well.
Best video I have seen on the topic. Nicely done. Thanks for sharing your expertise!
Thanks man! Bought some ChiCom repro lens covers, to replace the old yellowed factory ones. Needed to get to the headlamp units. Youre a time saver!
If I replace my Xenon Headlight for am Halogen Headlight will it work just plugging in the connector?
great video! I recently bought new aftermarket headlight assemblies and bulbs and I'm experiencing hyper flashing with the turn signals on the new units, I'm not using any LEDs just regular bulbs that are brand new and I hooked the old assembly back up and those worked fine so it's definitely something going on in the new headlight assembly, the manufacturer is no help but said to just return it... any ideas?
hey dude really really thank you, the next week I'm going to replace my headlights and I didn't know where start, especially with the bumper this two video helped me a lot, maybe you can tell me after remove the cap of the headlight how I replace the bulb (pull it, turn it or what I need to do?) Thank you dude! happywrenching
Happywrenching, I have a Mazda 6, 2002 I want to replace the halogen headlights with Xeon headlights!
Will that be a problem for the on-board computer or the wiring etc.? I would appreciate any advice...
Thank you so much I have an 06' Mazda 6 3.0 and I wanted to remove it but thought it had clips holding it on since Mazda seems to have tabs all over the place!!!! Also I have seen the bumper pull away at corner near headlights
No problem, glad the video helped :)
Are all the bolts the same length? I replaced my headlight when the harness rotted out, with the help of your video I was able to complete the job in about an hour on my own. Thanks
Great video! I look forward to replacing my headlights on my Mazda 6.
The car in the video is 2006 from North America. As long as your Mazda 6 is a first generation then the steps in this video will work. If you have a second generation (came out in 2007 and 2009 for North America) then the steps will be different.
Thanx buddy. You just made me a hero to a girl lol!!! Keep it up!! :)
thanks for both videos! (front bump and headlight)
Very helpful video's. Now I have a question I have 08 Mazda 6 the park light bulbs need replacing. Do I have to pull out the headlight or can I just open the hood and simply replace parking light bulb? Sorry if this is a stupid question. Again your video are very helpful. Thanks for your time.
Hope you see this, been a while. I frayed the interior headlight ( not highbeam) wore when trying to put in a new bulb. Just replacing the headlight assembly will solve this issue as it is already wired, correct?
Very helpful! Easy instructions.
happywrenching, 2 questions... First, my low beams seem awful dim on my '05 Mazda 6 Sedan, the headlight lens are actually clear but I'm wanting to brighten my low beams with replacement bulbs, what would you recommend? Secondly, it looks like there are 4 bulb ports in these headlight systems, what is the port between the turn signal and the high beam port used for, are there supposed to be bulbs in there? I don't see that anything comes on in them, high or low. Thanks for all the Mazda videos too.
+txtpqb Might be too late, but the answer to your second question - the port between turn signal and high beam is actually an integrated fog light on models that don't have them down in the standard bumper location :D
You can remove the low beam bulbs without removing the front bumper. I have done it several times already.
Yes there is no need to remove the bumper to change the bulbs. This video is for those who are looking to remove the whole headlight assembly. I just showed the shot of the bulbs as an extra.
I have a Mazda 6 that I always park outside. Due the the oxidation it has also become foggy. I recommend doing a headlight restoration, which just sands off the oxidation and following up with a headlight sealer. It makes it look like new and it cheaper than replacing the headlight.
A good , patient headlight restoration will solve lots of ills. This can take up to 1-1/2 hours per side. A good headlight restoration kit, such as that sold by 3M, will set you back $15 to $20. You will need a small drill. Everything else is included. Be careful to take your time during each step. It’s well worth it and beats the heck out of removing the bumper and headlight assembly. Use a good sealer over the lens once you are done. This prolongs the time between restorations.
awesome videos, is it nessesary to remove bumper and headlight to change the ballasts ?
Yep, if you got the factory ballasts then you have to remove the bumper and headlights since the ballasts are mounted on the bottom of the headlight.
Greeting! I have 2 Mazdas 6 in the family, 2006/2007 GG, one long hatchback and one sedan. They are the same, but the hatchback has factory xenon. I am keep just one, I would like to move a set of front headlights with xenon to the sedan version. Is it possible without major obstacles?
Great Video - but it doesn't address what I was hoping to see which would be the install (or, more accurately, the adjustment of the newly installed headlight). Would you be able to do a video on adjusting the headlight height on a 2014 (or similar setup) Mazda3 (I have the S Touring) - It is more a gear type assembly than the screw adjustment like on older cars. Thanks if you can!
+rychendroll Won't be able to do a video since I don't have access to a Mazda3 at the moment. Hope you find the info somewhere else. Thanks for stopping by!
No problem and thanks for the reply. Figured it didn't hurt to ask!
Thank You Sir its very haalpfull me , Greating from Hungary
It's really stupid that we have to take the whole front end off of a modern car in order to replace headlamps. I just changed the low beam in my CX-7. It wasn't half as bad as this but what a mess it was compared to changing the sealed beam on my old '69 Pontiac. Whatever happened to cars that made sense? Shame on the myopic designers of these automotive nightmares! Thanks for posting.
Au Gor
Thanks for this. I think it sucks they make it so involved. Wish I had bought all new bulbs while I had it all apart. I did replace the low beams with halogens. It also sucks you can't buy just the front lens. It looks like it's only held on by a few clips. Would make life a lot simpler. Thanks again.
+john meadows doesnt seem involved at all, take out a couple bolts unplug it, put the bolts back in.
I actually have a guide on the website that shows how to replace the lower control arm. I think a control arm video would be a nice addition.
I have a 2006 Mazda 6s 3.0 and want to replace my headlamps, but I am given two choices a Standard and a Sporty. Do you know the difference? This is not the one that uses the Xenon bulbs. Mine uses the regular Halogen bulbs, but there's the Standard and the Sporty, I don't know the difference.
Sport and Grand Touring packages came with headlights and taillights that had black surrounds. Base models had clear surrounds. The car in the video is a 2006 6i w/ the sports package and if you look at the headlight you can see that the inside is tinted black.
Hi "Mr Happywrenching", thanks for your info. Would you please how to take out the light bulb (how to disconnect it... for sure is simple but I heard that we shouldn't touch the glass part with bare hands.
Request a video about aiming the headlight assembly once you install the new one.
To do that you're going to needed to remove the dashboard, the rear wheels and all control arms, the intake manifold and remove the timing chain.
Thanks for the videos Ron Swanson, some of those screws were a real bitch.
Hello, I was wondering. Wht are the bulbs used for the Mazda 6? One of my fog lights has been burned out and needs replacement
+Enyer Rivers any autozone can answer this, they have it in their computers.
Thanks!
So there's no other way to replace the headlights besides taking the bumper off? Also I have an 08 Mazda 6i which doesn't have fog lights, but if I take the bumper off can I install the fog lights then also? Love the video btw! I'm a chic who's not super skilled with mechanics but hopefully can pull this off rather than bring to a dealer like my guy wants me to. :)
That's right, the bumper has to come off to take out the headlights. As for the fog lights, there are several more things you need to make it work such as the correct wiring harness and the switch - not an easy task, mostly because of the harness.
Does this video apply to the 2007 Mazda 6, as well? Also, how do I replace the plastic cover to the headlights? Mine is faded and dingy. I'd love to replace them as soon as possible. Thanks for the videos!! Since I just bought this 2007 Mazda 6, I subscribed to your channel. I can see it's going to be very useful. Thanks again.
Yes, this video applies to 2002 - 2008 Mazda 6. I'm not really sure what you mean by plastic cover. As far as I know the headlight is one unit - you cannot replace anything on it. Thanks for subscribing :)
What I meant by "plastic cover" is the clear piece that covers the actual lights, themselves. The outer piece. Mine has yellowed and is quite dingy. I hope I can replace them. However, if I have to actually replace the entire headlight system, I'll just have to live with them being yellowed and dingy, I guess. Thanks again.
Yeah, unfortunately that piece cannot be replaced - the whole headlamp must be swapped out. I'm in the same boat - even though I've cleaned and buffed them, over time the cover turn yellow again. Mine even fog up on the inside. Don't really want to spend $130 per lamp so I just live with it.
Okay. That makes sense. Well, I guess I'd better start saving up my money. Since I just purchased the car, and LOVE it!!!!, I don't want to deal with yellowed, dingy headlight covers just yet. :) Thanks for your help.
3M makes an excellent headlight restoration kit, available for $15-$20. If you are very patient, taking as much as 1-1/2 hours per side, you can eliminate those dingy, yellow headlights. It’s imperative that you take lots of time for each step. Tool needed: 3/8” electric drill. Also, some paper or microfiber towels.
Thanks for the help. Worked like a charm.
Great video, keep up with these great videos
Whenever i have to replace a headlight bulb on my 2003 madzza 6 i have my daughter do it for me since her hands are small and can actually fit inside the headlight assembly . There is no way my large male hands can do fit in there.
Do you happen to have a video on how to remove the fender off of the Mazda 6? Someone backed into mine and now I have to replace it, but I'm not sure how difficult it might be.
Unfortunately i don't have any videos on removing the fenders. However it is not difficult. You have to remove the three bolts on top of the fender. Remove the headlights and bumper and under that you will find one more bolt. There is one bolt under the cowl cover (which you have to remove to get at the bolt). Finally there are two bolts on the bottom of the fender. I may actually do a quick video on this.
Do you know if the Halogen versions can be swapped out for the Xenon versions on the 2006 - 2008 ones or is the wiring different?
Good job! Useful video
Glad you found the video helpful :)
Thanks man, saved me money
Yeah its pretty easy. I don't think anybody will have a problem doing this on their own.
Hi is it generally simple to replace all headlights? We have a Mazda Mpv van that we need to replace the headlight.
GREAT VIDEOS! THANK YOU SO MUCH FOR THIS!
thank mas i had to do this because the little light on the high bean fell inside ... hey do another video on how to change controll arms in the mazda 6 since is a common problem
Are there two low beams in each assembly?
Köszönöm Sir, segit a következökben ha neg kell csinalnom.Many Thanks
How do you take the small parking light out next to the high beam
look on the back of the headlight. you will see a small turn knob that is in line with the bulb. turn and pull that out.. its a long tube that comes out before you see the bulb. Takes 20 seconds to change a bulb from start to finish.
Pause vid at 3:05. The light gray long tab looking knob is the one I am talking about.
Brian Arnold thanks :)
Hi, one of the bulbs on my headlights are out but when i hit the bumper, it turns on. Can you help me figure out why it does that?
You dont have to remove it all the way, Undo the top 10mm bolts and sides if theyre not already broken, slide the bumper forward and you should have room to work. If youre just replacing low beam bulbs I suggest just undoing the fender-wells and replace bulbs from there.
Turn the wheel inward on the side with the blown bulb, take off the 3 plastic screws and pull back the plastic barrier. Easy access to the headlight, 2 minute repair with no bumper removal. '04 Mazda 6
Thank you man, very helpfull!
+Felipe Diaz You're welcome :)
I am about to install myself new headlights in my Mazda 6. I recently cracked one by running into a mailbox lol...dont ask. But i would like to know if this Mazda 6 is a 2008??? NEED TO KNOW so I can disassemble correctly, please respond , and thank you!
Very helpfull video !!! Time to save some money !!!
I especially enjoyed the slight accent changes.
Can you please do a video about how to remove Mazda 6 frount fenders
When I want to look like I'm a great mechanic to a girl I just go to RUclips. LOL thanks.
How do you replace a bad socket in the headlight assembly?
I wish I would of seen this before taking mine to the body shop to replace both headlights. When I picked it up, now the HIGH beams turn on simultaneously with the regular/low beam bulbs. Why is it doing that now? Did they just accidentally switch the high beam and parking bulb connectors or what? I want to avoid taking it back to the shop if I can do it myself. Sorry I'm not car savvy.
Does those headlights have a vent hole or holes? If they do then where?
What is that plastic piece called on the corner outer side
Great video! Thanks so much!!
Thank you, I know what I'm doing tomorrow.
Can you please tell me if the bulbs at 3:31 can be found in a regular auto parts store and what they're called.? Thank you
Grisel's Pages Grisel's Pages Those are the integrated fog lights. I've never found them in regular stores, I think they're only sold online.
Do you know if the 2006 mazda 6 headlight housing fits the 2007 mazda 6?... I am looking to upgrade headlights but I am only seeing from 03-06
Basically there are two sets of headlights for the first gen Mazda 6 - one set for years 2003 - 2005 and one set for years 2006 - 2008. The wiring is different between the two sets. The upgraded headlights that you are seeing for 03-06 will not work with your 07.
happywrenching alrighty thanks for the help... and your vids are very helpful
i have this car in silver with custom suspension. i love it
I swapped a fusion 2.3 engine when I first bought the car. That was at 98,000 miles on the odometer. It now has close to 170,000. Nothing but regular maintenance and the car is still going strong. I love mine as well.
Great video
pull the inner finder out and it's easy don't pull the bumper there is no need to if it's just the driver side
Could you explain to me I'm trying to replace my Bulbs but I don't wanna take bumper off I have 2005 Mazda 6
great work thanks for that video
At 2:00 minutes into the video you take a screw out of a white tab/clip do you know what that part is called mine broke n now I can't get the corner of the bumper to stay in thanks
That is the front bumper bracket - Mazda calls it a slide. Part number for the right side is - GJ6A50E11C and GJ6A50E12C for the left. They sell them on eBay for around 10 bucks. Of course you can also get it at a dealer.
Thanks greatly appreciated.
What year model Mazda is this please?
you should do s video of the fender removal
Is this guide for a 2009 as well?
Only applies to 2002 - 2008. I've added the info to the description as well.
Al mecánico gracias por orientarme Thank you a lot for the video
My is the right size. Not working I changed the fuses it didn't fix the problem!.
good instruction
Will this work for a 2010 Mazada 6??
+Elbe Vargas no, 2010 is a 2nd gen. this is a first gen
I was there and you weren’t, so I did it myself.
Where is Mazda 6 TCM and ABS computers?
Two things;
1) 2013 was 11 years ago... That's crazy!
2) Dropping the bumper?... Ridiculous! Mazda should be ashamed of themselves.
I replaced my BMW headlamp buckets last year and all four bolts have specific access. Now I want to do my girlfriend's and it's going to be a bit of a project.
At least I'll look like a hero. :)
Big Halp for me, thanks Sir
Could they have made this any more complicated? I mean wtf...
Very useful, prolly easier breakin into a bank vault
Tear the hole car apart just change a light bulb that crazy
Danke schön
What the absolute hell? Why do you have to disassemble the whole front end to replace a headlight in these cars? Does no one else think that's just crazy or am I just old?
Thank you
Thanks mate