Oh god within the first minute i saw a monster use a hammer on a step bit and finger wagging. Dam the rusty bit along with the drill transformed into a shiny bit and a cabled drill, crazy magic going here.
Ты кого обмануть решил ,с начало после заточки шуруповёртом сверлит,где прекрасно видно,что ни хрена не сверлит, потом кадр обрывается и уже сверлит дрелью с другим сверлом😅
If you sharpen the drill correctly , it won't get hot enough to require quenching . Besides that this is just another click bait video put together by some unskilled " expert ". You only have to look at the swarf coming off the bit after it's " sharpened " to see that it is chipping rather than cutting its way through the stock , because he has ground the bit in one plane only without regard to the trailing edge . That will not allow the bit to dig in and cut . It won't last either . Don't get me started on the conglomeration of junk to pull off this stunt . For the same money or less you could buy a small 150 mm bench grinder from your local tool store and do the job properly , or spend half that and get one of those units that you bung on the end of your drill which are foolproof . IE , even fools can't shag their drill bits using these things ??
@@grayamdelaney7044 sorry Grayam, I was toolmaking for 50 years before I retired, if I had not quenched the drill when I was an apprentice | would have got a "clip round the ear" from one of the "old hands"! Actually ground properly the leading cutting edge of the drill bit has a thin cross section, so will get hot very quickly and so coolant is always required. From the front cutting edge the rake angle (giving clearance) the cross section gradually becomes thicker, so wont get so hot so quick, but the very front edge must be tackled very carefully. The drill in question has had its front angle almost completely removed, therefore has has a "serious regrind" which will require quenching or the front edge will lose its hardness and its cutting life seriously reduced! You are correct regarding "trailing edge" (rake angle) giving it clearance allows it to cut and swarf will fly, without that it will rub and chip and not last 5 mins!
Excellente idée pour ceux qui ne savent pas affuter un foret. Mais il faut remplacer dans le titre "perceuse" par "foret". Personnellement je préfère affuter les forets avec une meule et en plus à chaque fois j'amincis l'âme du foret ce qui rend la pénétration dans l'acier plus facile.
Ну для кого правильная заточка - пользуйтесь этим способом, а мне показывали несколько другое... на "пяточке" делаем заовалку... а на "носочке " "фасочку" снимаем....и сверло дольше служит и меньше тупится....
These are NOT drills. Drills are machines, specifically involving more than one moving part. These are BITS. Say it with me now... BIT. Stop calling bits drills 😂 🤡
@@jaisookram2255 *Drill a hand tool, power tool, or machine with a rotating cutting tip or reciprocating hammer or chisel, used for making holes. Similar: drilling tool boring tool rotary tool auger (brace and) bit gimlet awl bradawl 2. instruction or training in military exercises. "parade-ground drill" Similar: training instruction coaching teaching grounding (physical) exercises workout discipline square-bashing verb 1. produce (a hole) in something by or as if by boring with a drill. "drill holes through the tiles for the masonry pins" 2. subject (someone) to military training exercises. "a sergeant was drilling new recruits"
bit3 /bit/ noun noun: bit; plural noun: bits 1. a mouthpiece, typically made of metal, which is attached to a bridle and used to control a horse. 2. a tool or piece for boring or drilling, typically of metal. "a drill bit" the cutting or gripping part of a plane, pliers, or other tool.
Saying these bits are drills are akin to saying a "drill" is a screwdriver because you can put a driver in it...just because you can attach a bit to it that performs a certain function doesn't make the machine become that bit or attachment. Or saying a reciprocating or circular saw is a "blade".
Gość niech przestanie niszczyć narzędzia! To nie ostrzenie, to katastrofa. (Let the guest stop destroying the tools!This is not a sharpening, it's a disaster!)
4:35 минута показывает , что угол атаки сверла не правильное, таким сверлом ни то , что метал - дерево не будет сверлить, и почему то сверло с заточки чистое, а сверлит 4:44 уже вымазанным в древесную смолу
COMMENT AFFUTER UNE PERCEUSE ????????? LOL DEJA 2mm20 pour faire l outil mais comment peut on affuter une perçeuse incompréhensible là c'est un foret qu'il affute aucun rapport pour l'affutage d'une perçeuse MDR🤣🤣🤣🤣🤣🤣🤣🤣🤣
Un burghiu bine ascutit scoate span continuu ambele parti la gaurire . In videoclip e eroare Un burghiu trebuie sa. aiba unghiul intre 95 grade si 100 grade .Cel din videoclip avea cu mult peste 110 grade .Mai. mult freza decat gaurea .
Erstens: Bohren ohne Schmieren bzw. Kühlung geht gar nicht ! Unbedingt die Bohrspaene betrachten da kam ja nur Abfall minderer Qualität raus ! Also Frage Umsonst oder kostenlos gelernt fragt ein Meister / Techniker usw. Roland. Da hat einer wohl umsonst gelernt.
It would be nice to sharpen a drill bit in 10 seconds. But where do i buy that device. it would be nice to know where to buy and how much it costs and the name of that device. Beside that this video useless to me. i see videos like this all the time with no help which makes these videos useless. Do i buy this on amazon i would love to have that device but it has no name which make all your videos useless to me and others. One person called this a belt sander i have never seen a belt sander like that. I have a belt sander and it does not look like the one in the video. when i go shopping they would show me the common belt sander. A little more help would be nice that would make your videos really work.
Oh god within the first minute i saw a monster use a hammer on a step bit and finger wagging. Dam the rusty bit along with the drill transformed into a shiny bit and a cabled drill, crazy magic going here.
As a machinist who sharpens drills free hand...good luck with that!!
Не лучший способ
@@ВладимирСуховерз
I thought the same.
nicht schlecht 👍👍
Heck - I don’t need a lesson in how to dull bits. Starting with sharpening would have worked for me! Thanks for posting!
🤣🤣🤣
Scharfe Bohrer machen andere Späne. Und zum Schärfen reicht ein Schleifbock, eine ruhige Hand und wirkliche Ahnung.
Gute Meinung ,ruhige Hand und Schneid Geometrie beachten.
Máš pravdu,aj tak to brúsil pod zlým uhlom.
I think that was distinctly longer than ten seconds. In the time it took to make the jig I would have sharpened the drill free hand on the grandstone.
Лучше всех этому учит Леонтьев. Причем про разные заточки подробно. Этой заточке я не поверил
wo hast du die vorrichtung für den banschleifer gekauft ?
Very good idea. I shall try it. Thank you.
خسته نباشی🎉🎉🎉
Que largo, que ancho y que alto son las medidas de la tabla....?
Если на конце сверла убрать чуть чуть перемычку, сверло
при заходе не так сильно будет
шатать.
Ok
It's not a drill, it's a bit.
Простой способ -это на зачистной чашке и слишком большой задний угол в плане для сверления стали.
Nice video, keep it up, thanks :)
Nice tip. But now I gotta spend big $$$ on a belt sander, instead of little $ on new drill bits...
😊
Bukur . 👍
Ты кого обмануть решил ,с начало после заточки шуруповёртом сверлит,где прекрасно видно,что ни хрена не сверлит, потом кадр обрывается и уже сверлит дрелью с другим сверлом😅
Я тоже это заметил. Потому что точить не может нихрена 😂
Да у него все такие видосы, я сейчас спецом глянул 🤣просто монтаж на монтаже
10 seconds ? get a new watch/clock!
Started to drill with the green drill, finished drilling with the blue electric drill.
Facile e semplice, il più pratico sistema che abbia provato! Bravo grazie
Это классно
👍👍👍
Зачем вы городите хрень, поднесли руками под углом сверло да и попрвили вот и все.
How to sharpen a drill bit in 10 seconds, but the video is five minutes long. Go figure.. 👎
Wrong angle on the drill point, also it would lose its "hardness" if you dont dip in a water/oil coolant every few secs whilst grinding the point!
If you sharpen the drill correctly , it won't get hot enough to require quenching . Besides that this is just another click bait video put together by some unskilled " expert ". You only have to look at the swarf coming off the bit after it's " sharpened " to see that it is chipping rather than cutting its way through the stock , because he has ground the bit in one plane only without regard to the trailing edge . That will not allow the bit to dig in and cut . It won't last either .
Don't get me started on the conglomeration of junk to pull off this stunt . For the same money or less you could buy a small 150 mm bench grinder from your local tool store and do the job properly , or spend half that and get one of those units that you bung on the end of your drill which are foolproof . IE , even fools can't shag their drill bits using these things ??
@@grayamdelaney7044 sorry Grayam, I was toolmaking for 50 years before I retired, if I had not quenched the drill when I was an apprentice | would have got a "clip round the ear" from one of the "old hands"! Actually ground properly the leading cutting edge of the drill bit has a thin cross section, so will get hot very quickly and so coolant is always required. From the front cutting edge the rake angle (giving clearance) the cross section gradually becomes thicker, so wont get so hot so quick, but the very front edge must be tackled very carefully. The drill in question has had its front angle almost completely removed, therefore has has a "serious regrind" which will require quenching or the front edge will lose its hardness and its cutting life seriously reduced! You are correct regarding "trailing edge" (rake angle) giving it clearance allows it to cut and swarf will fly, without that it will rub and chip and not last 5 mins!
Exactly
@@pedrogroves77777 it's not a drill, it's a bit. A drill is a machine, a bit is not. It's the cutting extension of the machine called a drill.
@@A_Stereotypical_Heretic actually it's a drill bit!
Заточил и сразу убил сверло))))
Excellente idée pour ceux qui ne savent pas affuter un foret. Mais il faut remplacer dans le titre "perceuse" par "foret". Personnellement je préfère affuter les forets avec une meule et en plus à chaque fois j'amincis l'âme du foret ce qui rend la pénétration dans l'acier plus facile.
Wenn ich schon sehe, dass er einen Stufenbohrer zum ankören nutzt...
I don’t believe you can sharpen a drill.. But you can a drill bit.
Ciekawy poradnik
Podobnej tandety dawno nie oglądałem
Wooden jig measurements? Leght x height?
Ну для кого правильная заточка - пользуйтесь этим способом, а мне показывали несколько другое... на "пяточке" делаем заовалку... а на "носочке " "фасочку" снимаем....и сверло дольше служит и меньше тупится....
Why, when testing the just-sharpened drill-bit, does it appear to swap electric drills?
had to go to a factory sharpened bit ?
Cutting the groove with a hacksaw blade for metal. Novel.
Yes. Exactly ten seconds.
Was für ein Winkel hat der Klotz. Das wäre vielleicht wichtig
az sem mindegy, milyen anyagnak milyen fokban van élezve... ettől különben megélezem szabadkézzel, és nem smirgli papíron!!
Bravo! Super!
These are NOT drills. Drills are machines, specifically involving more than one moving part. These are BITS. Say it with me now... BIT. Stop calling bits drills 😂 🤡
Nah, they are drill bits, say it with me now, d r I l l b I t s.
It's called a drill, the machine is called a drilling machine.
Or maybe we call it different things 🤔
@@jaisookram2255
*Drill
a hand tool, power tool, or machine with a rotating cutting tip or reciprocating hammer or chisel, used for making holes.
Similar:
drilling tool
boring tool
rotary tool
auger
(brace and) bit
gimlet
awl
bradawl
2.
instruction or training in military exercises.
"parade-ground drill"
Similar:
training
instruction
coaching
teaching
grounding
(physical) exercises
workout
discipline
square-bashing
verb
1.
produce (a hole) in something by or as if by boring with a drill.
"drill holes through the tiles for the masonry pins"
2.
subject (someone) to military training exercises.
"a sergeant was drilling new recruits"
bit3
/bit/
noun
noun: bit; plural noun: bits
1.
a mouthpiece, typically made of metal, which is attached to a bridle and used to control a horse.
2.
a tool or piece for boring or drilling, typically of metal.
"a drill bit"
the cutting or gripping part of a plane, pliers, or other tool.
Saying these bits are drills are akin to saying a "drill" is a screwdriver because you can put a driver in it...just because you can attach a bit to it that performs a certain function doesn't make the machine become that bit or attachment.
Or saying a reciprocating or circular saw is a "blade".
Super ❤️
Muito bom mesmo
.,,, g
Actually putting 60 grit on the belt sander. Watch closely. Not 180.
Velice amaterské nabroušení vrtáku, břit vrtáku jsem viděl i níže než patka břitu. Vrtací stupně velký otazník, v učení nás učili 118 st.
И где тут 10сек.,тут ещё приспособить кучу надо, а не у всех такое есть.... 😢
Took more than. 10 secs.. about 120 ,I counted
Не указаны размеры бруска, от которых зависит угол установки сверла
Длиеа к ширине, как 2 : 1.
10 sec 😂 5 min.
Hack is correct, as in not worth doing. Doing it right isn't hard, especially smaller drills.
It's not a drill, it's a bit.
Your 10 seconds was up 15 seconds ago!
Háát ,az biztos, hogy nem így kell fúrót élesíteni !!!
Affuter un foret oui, une perçeuse NON 😂😂
Anyone who drills metal with a hammer drill gets my vote... What a load of tosh.
Начинает сверлить шуруповёртом,а заканчивает дрелью...Чувак,не лепи лапшу на уши...Мастер хренов...🤮
tourne trop vite pour de l'acier
118° soll ein Bohrer haben, davon sind wir hier weit weg
Maravilloso
Zabudol si uviesť uhol!!!
Y porque cambia de taladro???
Gość niech przestanie niszczyć narzędzia! To nie ostrzenie, to katastrofa.
(Let the guest stop destroying the tools!This is not a sharpening, it's a disaster!)
Dokladnie. Tak naostrzone wiertło to nadaje się tylko do plastiku czy aluminium
In quel modo fai i chiodi , le punte elicoidali vanno scaricate ,,smussate verso l'alto per scaricare i trucioli
Почему-то на видео дрели разные😁
sei partito con un avvitatore a batteria hai finito con un trapano elettrico 😅😅😅
4:35 минута показывает , что угол атаки сверла не правильное, таким сверлом ни то , что метал - дерево не будет сверлить, и почему то сверло с заточки чистое, а сверлит 4:44 уже вымазанным в древесную смолу
It's called a bit
Lovy černé zvěře 0:24 0:24
That's only a way with big drills.
Ну да, если бы мне таких приспособлений то Я построил себе не только самолёт но и ракету 😅
The thing I'm wondering why the guy starts with one drill and ends with a freaking hammer drill bro like obviously something not right there
kannste so machen aber dann wird es Mist und nie ein genaues Loch
A la hora de comprobar la bronca no debería de estar el percutor puesto.
Affutez le foret plutôt que la perceuse, vous travaillerez plus efficacement !!! Mais peut être est-ce une mauvaise traduction ?
Просто чудо а не руки👹👹👹👹
Pogresno. Nisu dobri uglovi.
Oder man kauft sich gleich Bosch X7 Bohrer..........
А почему сверла выкидываются на стол,как будто он играет в нарды.
Qu,El angle pour le support
La machine avec le ruban , qui la fabrique svp ?
J'aimerais également savoir où l'acheter
Pourquoi, la perceuse à 0,37 seconde tourne à l'envers ?
COMMENT AFFUTER UNE PERCEUSE ????????? LOL DEJA 2mm20 pour faire l outil mais comment peut on affuter une perçeuse incompréhensible là c'est un foret qu'il affute aucun rapport pour l'affutage d'une perçeuse MDR🤣🤣🤣🤣🤣🤣🤣🤣🤣
Quicker Ith a wheel
Had to use the drill with impact function to make it cut!!!! Incorrectly sharpened drill. People will post anything wont they!!!
Un burghiu bine ascutit scoate span continuu ambele parti la gaurire . In videoclip e eroare Un burghiu trebuie sa. aiba unghiul intre 95 grade si 100 grade .Cel din videoclip avea cu mult peste 110 grade .Mai. mult freza decat gaurea .
To bych chtěl vidět jak nabrousí na pásový brusce ten správnej úhel🤣🤣a hlavně břit bude pěkně do kulata!!
Mene interesuje gde ima da se kupi kavurma.
I gave up watching this because I thought it was only going to take 10 sec wth
so 10sec equals 5min video..
10 seconds after 30 min of prep. That's not sharpened well. How about using a bench grinder?
What if you don't have one?
Угол заточки неправильный. Таким сверлом только пластилин сверлить.
Yeah I don't think so bro lol
porque é que no video começa com um berbequim e depois acaba com outro?
compré una máquina de afilar brocas y aún que no era de los chinos ha sido un auténtico engaño.
Podaj kat ostrzenia
Erstens: Bohren ohne Schmieren bzw. Kühlung geht gar nicht ! Unbedingt die Bohrspaene betrachten da kam ja nur Abfall minderer Qualität raus ! Also Frage Umsonst oder kostenlos gelernt fragt ein Meister / Techniker usw. Roland. Da hat einer wohl umsonst gelernt.
gdje kupiti mašinu za oštrenja
It would be nice to sharpen a drill bit in 10 seconds. But where do i buy that device. it would be nice to know where to buy and how much it costs and the name of that device. Beside that this video useless to me. i see videos like this all the time with no help which makes these videos useless. Do i buy this on amazon i would love to have that device but it has no name which make all your videos useless to me and others. One person called this a belt sander i have never seen a belt sander like that. I have a belt sander and it does not look like the one in the video. when i go shopping they would show me the common belt sander. A little more help would be nice that would make your videos really work.
Al menos enseñen un taladro o broca desgastado,sugerencia
Man kan ikke slibe på 10 sekunder! Boret må ikke blive varmt!!
l angle n est pas bon , ni la depouille
ça coupe pas terrible
ça chauffe un peu
Empieza con un taladro y acaba con otro yo eso no lo entiendo
Обман! Начинает сверлить шуруповертом ,а сверлит дрелью!!!
😂 😂