BMW 318D ABS Ring Replacement, Both Sides. How To Diy, E91. Same as 320 118 120 etc. DTC.
HTML-код
- Опубликовано: 29 дек 2022
- How To Remove The Drive Shafts & Replace the ABS Rings.
I Fitted spacing washers to the sensors in another video,
Link is • BMW ABS Sensor Repair ... Spacing the sensor away from the corroded abs ring, and resetting the eobd codes will repair the system until the ring can be replaced.
I show in this video how to remove The drive shafts and replace the abs rings, overcoming some issues.
This fault occurs on all the rear wheel drive Bmw vehicles, but mostly the 3 series on the near side rear sensor. e90 e91 e92 e93 models
Links to all Parts & Tools Used In the video on amazon:-
ABS Rings & Drive shaft nuts £15 amzn.to/3vuBWdY
Topdon artidiag 600 diagnostics tool £199 amzn.to/3WBZXLO
Sealey Trolly Jack £159 amzn.to/3Vzd6nC
Milwaukee impact gun £394 amzn.to/3erqEz6
Wurth Rost off £8 amzn.to/2RuftNo
30mm 12 sided socket £15 amzn.to/3G4ZsTI
Milwaukee M18 Ratchet amzn.to/3vQxh3R
Deep Socket set £10 amzn.to/3xRtKUN
Knuckle bar amzn.to/2QZ4JGM
Aqua steel Rust Converter £21 amzn.to/42ec98N
Jenolite Rust converter £18 amzn.to/3IcUGpV
Wire Brush for angle grinder £15 amzn.to/3Z0sWdP
Bosch Angle grinder £80 amzn.to/3FXKUoA
Etorx Sockets £15 amzn.to/3G8mfhp
Impact universal joints £20 amzn.to/3WSjQOr
Sealey cut off tool £30 amzn.to/3vtOJNu
17mm wheel nut socket amzn.to/3jFgBMa
Ratchet Head for Bar amzn.to/2QRwPnv
Aluminium grease amzn.to/3nfgqJu
#e90 #e91 #bmw #bmwe90 #e82 
Авто/Мото
Anton, it's very rare il sit through a vid like this, i usually skip through to get the main points then crack on with the job (do blokes really read the assembly instructions😆), but I sat and watched every minute of this mate! Very engaging, clear and informative.
Superb. 10/10.
Glad you enjoyed it! Thanks for the great comments👍🏻👍🏻🛠
Great videos - you give us confidene to tackle these kid of jobs!!
Glad to help Thanks for the great comments👍🏻👍🏻🛠
Fantastic video.....and kudos to you for sticking with it......stuck bolts, nearly impossible access........hope I never have to do this on my 135i.
135i uses a different sensor, Thanks for the great comments👍🏻👍🏻🛠
Hi anton just come across your videos today great content am into the same things bike bmw am also from Leicester to thanks for the video's just subscribed thanks
Welcome aboard! Thanks for the great comments👍🏻👍🏻🛠
Great video thanks ant 👍😊
Glad you enjoyed it Thanks for the great comments👍🏻👍🏻🛠
Great video. Wish i was as calm as you 😂
Thanks for the great comments👍🏻👍🏻🛠
Good effort! My E91 started throwing up the DTS fault so I know I’ve got this coming. Will start with the washer trick on the ABS sensor first though. Definitely saved this video cheers.
Glad it helped Thanks for the great comments👍🏻👍🏻🛠
You make everything so easy hahaha
Thanks for the great comments👍🏻👍🏻🛠
Great, thanks!
You're welcome! Thanks for the great comments👍🏻👍🏻🛠
what a cracking video warts an all
Thanks for the great comments👍🏻👍🏻🛠
Milwaukee does a 12ah battery (quite expensive). Any idea if this will give more power to the impact gun compared with the 5ah battery? I'm inspired by your drive and determination to overcome obstacles to get the job done. Thank you.
The 12ah battery will for sure deliver a more stable power, the one I switched to was a fully charged 3ah high power battery which is supposed to be as good as a normal 6ah battery😂 the 12ah is a big lump, Thanks for the great comments👍🏻👍🏻🛠
Put copper grease on wheel hub. Good videos well explained 👍
Thanks for the great information👍🏻👍🏻🛠
Good job mate. now it's my turn in my 335i
Good luck, Thanks for the great comments👍🏻👍🏻🛠
What happens if you don't paint the rust that's been converted? Does it just rust again? Why doesn't the gooped on converter damage the ring or interfere? I'd worry about putting on the ring until all the rust converter is complete, but not sure.
It just dries like pva glue no issues, Thanks for the great comments👍🏻👍🏻🛠
Little tip leave a bolt in a bit an put bar between bottom arm an wheel to get wheel off
Thanks for the great information👍🏻👍🏻🛠
Hi which rust converter is that you used? I would like to get the same because jenolite and others leave a darker and more rubbery finish
Aqua steel Rust Converter £21 amzn.to/42ec98N Thanks for the great comments👍🏻👍🏻🛠
Hi ! How much torque on the bolts from axle shaft near the differential ? Thanks if you see this !
BMW specs are 20nm + 90degrees or Nice and tight😂 Thanks for the great comments👍🏻👍🏻🛠
Ugadugga tight 😂
Thanks for sharing, is this the same for the E46? Did you reuse the same hub nut with tangs? Thanks
It is very similar, new nuts needed, Thanks for the great comments👍🏻👍🏻🛠
Hi Anton, great video, one question, how long did this whole job take you roughly? Thanks
a couple of hours, Thanks for the great comments👍🏻👍🏻🛠
If the rings on drive shafts have been replaced on BMW 16i why does my car now feel like I can feel every bump in the road while driving not smooth like something not in place properly after costing me almost 400 from BMW it feels rough
Did they change ant suspension components? or pump the tyres up? Thanks for the great comments👍🏻👍🏻🛠
@@aaanton11 not sure the car feels a lot faster the normal night he suspension order to different my son says it's because its a BMW 16i sport that's how it should feel tyres are ok got check for correct air pressure.
Hi there, it seems like the socket you are using to remove the hub nut in this video is not of the Cr-Mo heavy duty type that you link to, but rather a standard (Chrome-Vanadium?) 12-point socket. Also, the wall thickness of the socket seems thinner than the heavy duty one. Can you specify what socket you used in this video? Is it OK to use for this purpose, with a slight safety margin? Torque rating?
The one in the link is better for this job the one I used is just an old Britool one in my tool box, Thanks for the great comments👍🏻👍🏻🛠
But obviously good enough, even with an impact tool, and torque probably well above 400Nm when undoing the nut. Why go for a Rolls Royce when a Vauxhall will do the job?😊
Is it similar for the front rings?
No the front doesn't use rings, Thanks for the great comments👍🏻👍🏻🛠
Hi. If getting garage to replace reluctor ring.. is it just easier for them to fit a new shaft instead? Rather than refurb it then add new ring? I dont have all tools to do myself. So refurb will be labour cost but it might be same cost as getting new? I would need 318i se 2.0 for 2011 plate. Both rear shafts. I have no idea of brands and what are approved bmw parts. Ivr seen new shafts as low as 50 quid and up to 225. Obviously i want cheap as possible but good quality. Max i want to spend on each shaft is 110 if possible. Any recommendations on a drive shaft brand from anyone? Also will it come with ring? Thanks
Yes the garage will just replace the shaft, inc abs ring, Thanks for the great comments👍🏻👍🏻🛠
@@aaanton11 thank you. any idea how much i should expect to pay for each shaft? because clayton cars in Bristol who are a specialist quoted me £550 each shaft! when online they start at £60
What grease you are used?
amzn.to/3nfgqJu this is the link Thanks for the great comments👍🏻👍🏻🛠
Hi Anton. Can you do this job for me if I bring you my car?
Sorry I am stacked out, Thanks for the great comments👍🏻👍🏻🛠
Any tips to knock the shaft through the hub? Yours seem so easy to come out, mine are stuck solid, sprayed them and could be knocking them for ages and nothing happens 😂
Use a Drift and a Big Hammer it will shift Thanks for the great comments👍🏻👍🏻🛠