Good video very helpful one thing I’ve done when changing these reluctor rings is boil the ring in cooking oil on the kitchen stove to expand it and it just drops over the cleaned driveshaft
Excellent video and explains it all clearly - many thanks! Proper old-school mechanic is the way to go as BMW dealer would have swapped out sensor first and once they realised it was this problem (the reluctor ring) their answer was to swap entire driveshaft with the new ring on it. Difference in cost over £1k!! Problem with this fault is that, until you get a solid fault (permanent warning lights) which logs the error to tell diags which wheel the problem is on, you get the annoying intermittent symptoms of DTC kicking in when it shouldn't, engine stuttering & losing speed etc. Great tip at end about spacer as a possible intermediate fix.
Thank you for sharing this with us! The trick with the washer just saved me for now. The ring is bent on my X3 and damaged the sensor. Unfortunately 2 from the 3 guys at my local service are ill so they couldn't schedule the repair for this week. I have tried puting a 1+1/2mm washer initialy, but that turned out to be too much. The lights went off as soon I did change the sensor but when I applied the breaks first time ABS just kicked in, then all the light come back, except the tyre presure one and the ABS was completely switched off this time. I replaced the washer with a 1mm and that worked, so everithing works as expected for now. Again, thank you for sharing!
Just replaced my reluctor rings after watching this video yesterday, followed what you said to do, I done both sides as I noticed the sensor in the side that didn’t have a fault was scratched so thought while I’m there I’ll get it done, thanks a lot even though I’m a qualified mechanic I still research every job I do, (depending on timescales). And if I can I like to watch a RUclips video as it gives you a good understanding and also heads up for what tools I’m going to need. Thanks Gerald
I am the same exact way. Even if I know how to do the job. Might have done it once or twice or even ten times before. Will like to go ahead and watch a video a refresh my self before every job lol.
I watched your video week ago .. done the job today testing the car tomorrow... let's see if it is fixed ... like you said try and fail rather than not try all all thankyou for posting this video appreciated
The people who make the rings say you should heat the ring up so it slips over with very gentle taps then as cools shrinks for a permanent fit. You can also space the sensor back with a washer
Awesome video, clear and concise, thanks for sharing... I have an E91 2012 with 125K and this is a job that I will be tackling tomorrow if the rain stays off
I'm having exactly the same problem. I cleaned the ABS reluctor ring, and changed the ABS sensor (Already 3 times... Arghh!!!). I was planning on changing the full gimbals, but I'll try this method first... Let's cross fingers, I'll give you feedback ! Thanks for the video !
Very informative My car is in the garage at this very moment having both rings replaced. Having watched this video I am glad that I left the job for an expert to do.
@@suzesiviter6083done mine today was bashing it for ages gave up for a bit to have a sandwich and came back with a sledge hammer 3 wacks and it was out lol
Really good video thanks very much, another problem seems to be releasing the driveshaft nut. Great tip about fitting a washer to increase the spacing of the sensor slightly, thankyou.
Simular problem on my 318D 2011 model, TSC kicks in out of turns and sometimes on straights even though the conditions on the road is fine. (So the light is not on all the time like in this case) The repairshop here in Norway wanted 1200$ for the fix, they didnt mention if they would replace the entire axle or just the ring (Overpriced country, in every aspect) Will try this fix when winter is over :) Thanks!
just a note ABS rings are heated up wich exspand them,wich alow you to drop onto the drive shaft and you can place the drive shaft in a chess freezer if you have one wich shrinks the metal,
Awesome video I had A ABS problem traction kept engaging , 2008 BMW 328. The ABS ring was rusted like in the video so my car ABS kept engaging while I drive. I plug my OBE computer and it showed my sensor was reading incorrect wheel speed. I changed the entire axle. But doing what he did is much inexpensive and will work..
Another good video...you have far more patience than me..I always replace the drive shaft ..The price of the drive shaft and the price of the extra labour for the time cleaning and fitting ring probs works out the same
My ring had snapped while I was driving luckily I checked them found that was the problem now I've just got to buy my new ring and do the job what you've done but mine is a Citroen Picasso front wheel drive so hope it is easy to get off as that one is thanks for the video great insight in to the abs system
Hi Gerard, thanks for the video. I had this problem last year on my E82 with a similar mileage to the E90, but sorted it by removing and cleaning the sensor. It returned again very intermittently last week whilst on the motorway so I'll try the washer route first, Thanks again 👍
Great video Gerard I have the same issue with my e87 and changed the sensor and the lights are off so hopefully that's it, but there was wear on the end of the sensor so I'll probably have to change the ring next but I know the process so thanks for that.
Surely without any rust treatment it will corrode in 12 months? Maybe give it a light coat of paint. I’m trying the washer/shim method first. Good video thanks
Thanks for posting! Not too short video, nor to long. Just enough to cover every detail. Perfect. Would you recommend using a primer/anti corrosion of some sort over the bare metal before fitting the ring and placing it all back togheter, though? The bare metal would probably start rusting in just a matter of days after fitting it(?).
Great vid, thank you. Got this problem currently on my e92. How long did it take for the sensor to correct itself and the lights to go out when you test drove it?
Thanks for the video, however I can't understand why people make these videos without telling you the year, make, and model. Thing are different on each year and model
Thanks for your great video. same issue. started with fuel pump, then to module then abs. turned out that it was the ring on the drive shaft. cost me £900 all in. 😞
Brilliant video thank you. Tried the washer trick but it didnt work. I can see the ring on mine is as bad as urs was. I've ordered a new ring and sensor and il be following ur video step by step to repair mine. Thanks very again.
Thanks for sharing, very clear and helpful video really. I had exactly the same issue, the mechanic installed washers which solved the problem temporarily, six months later the lights comes up again, I guess it need to put new rings and do the same job as here, I’m just wondering how much that will cost to do in Ireland? Thanks again
I used kurust on the driveshaft reluctor ring down the sensor hole, fifteen minutes and cured. This will helo reduce speed of rust growth, I fitted a 1.5mm washer, test drove and got all sorts of faults from airbag to juddering brake pedal. Repeated with 1mm washer and car drove fine with only abs fault. Just need to drive car for enough miles to reset the light. Or did you have to use a reset tool?
I agree Nathan, If you want to be certain of a fix it and it looks like this one, I would advise full shaft change. If you want to try it out on your own time and you don't mind failing, ya could save a few bucks as the ring is so cheap.
@Gerard Burke do you remember, how much miles/km you drove until the lights gone off, after you replaced the reluctor ring? I did the exact same same thing, before I saw your video, but the lights on my E90 are still on
Little tip from us. Grease or wax up the ring it will prevent future corrosion. We use Dynax UC wax before they get bad. Works a treat and does NOT affect the magnetism or operation in any way. It's a shame everything is assembled dry in the factory @Jules75ZT
Is there a possibility that because i put a wire brush adaptor on end of the drill and put it in the sensor hole to polish the ring while turning the disc.. Fitted two new sensors .. But fault still is on. Have I polished the magnetic coating off the ring? Or is the abs ring magnetic all the way through? I think ive wrecked the rings thinking I was cleaning them through the hole 😢
Gerard ,scan tool is saying rear right tooth missing but rear left looks just a bad , if left was also bad would scan tool say so or is it going to tell me after i fix the right ? do you know ?
Luckily I just found a rear left cv for 15$ brand new. Grabbing a right and going to just replace them both. Tired of fighting this damn abs situation. Washers on the sensors worked for about 2 weeks but now it's on, always.. Hopefully my sensors are still OK. They were new, but now I think they be scratched
Where did you get the reluctor ring? I found one UK based website but I'm having problems trusting them. My car has a different size depending on if it's automatic or manual (E46 330i) and they don't list which one they are selling, and they have a model in their line-up that doesn't exist, and E36 330i, so I don't feel comfortable buying from a parts dealer that has both missing and incorrect information on the same page.
I know this isn't the same vehicle, but I have a 09 128i (e82) and began receiving traction issues on the dash. The mechanic stated that axel and wheel sensor needs to be replaced. Does this sound right?
This is such an awesome video, thank you. I have a 97 E39 528i that has the abs light on too I don’t have a tester so wondering if the sensors are only on the back wheels, or all four?
Your thumbnail shows a toothed reluctor ring but your video shows the segmented one from a different driveshaft. Mine looks like it has an inner diameter of 72mm but that doesn't match anything online - any advice? a bit desperate now sorry.
hi im haveing this same problem for about a month now would this make my engine light come on and my passenger light come on andthen stop the engine and not make it start agian ordo i have a more serious problem any help and advice would be most appreciated!!!!!! thank you 🙂
Hi, thanks for the great video. Are any special tools needed to get the driveshaft back into the wheel hub once the ring is changed, or is it just a bit of elbow grease?
The answer is yes, I showed replacement of driveshafts in a later video. I will post up a link when I get to my pc or just search my channel for BMW videos 👌
You can do a visual check and see if anything is rubbing/out of round or use a scan tool capable or reading wheel speed sensors and simple road test or manually rotate wheel when jacked up and look at the live data.
reluctor ring is virtually the exact same design on my peugeot van, and its had a crack in it, so now and again would slip to an off angle and catch the hub and not spin, didnt matter when driving, but it was really important when braking! you approach a roundabout and then the pedal would start fighting you back! your slowing down for a slip road off the motorway and it goes into 3 wheel braking and tries to throw you off into the ditch... epoxy glue fixed it..... some abs systems (and there all re-badged bosch really) (except the ones that are toyota) are more forgiving than others, being a van and a 2005 its really basic and forgiving of 'variation' i do not recommend that anyone reading this repairs with glue or non standard parts!
Great video very informative , I am having a issue with my 320D automatic when I put foot down from the 4th gear to fifth it struggles there is jerk sometimes or it’s says transmission fault on dash board , only it happens when my car is fully loaded with passengers or if it’s uphill, I took it to the Bmw they said it’s not transmission fault it’s the pick up ring on rear driveshaft it’s corroded and it’s swelled up so it’s touching ABS sensor and full driveshaft needs to be replaced, well I am thinking I can change the rings and get it fixed, what do you think Mr Expert? Thank you
Thank you for your kind words on the video, It is nice to hear feedback. I replied to another man with pretty much the same issue as yourself. I will say to you like I said to him. It all depends on how bad the corrosion is, then decide on if the repair of just the ring is worth it or not. I have done quite a few of these now and all of them have a lot of time to be invested to solve, In one case the repair was not successful, it was just gone too far. (none of them were the same) When it is your own time it makes sense to go with the ring but when paying for labour it's probably makes more sense not too, unless the corrosion is in it's early stages (much better condition than in my video) The amount of time that's needed to get it right means it is cheaper/quicker to fit a shaft. This job is very much a labour & parts combined issue, one has much more labour and small costing parts and the other is vise versa. Depending on the quote they give for replacing the shaft I would say proceed, If they are way too high I would bring it to an independent workshop that's gives you better value. Regards Gerard
Is your egr valve plunging in and out ok? Judder from cold can be caused from that, use few drops of engine oil to lubricate. Really easy pop plastic cover and you will see.
It has hills valleys that magnetically interact with the sensor providing a series of pulses as they spin by the sensor. The computer looks for repitituous pulses.
Hi are there one reluctor ring on each side or just the drivers side? I have a e93 coupe and am about to buy replacements but want to know if theres one reluctor ring on each side so I have to replace one or two? Thanks...
Each wheel must have a pickup of some sort for the ABS/traction control etc.. varies for different makes and models. but in general these monitor all 4 wheels so if any slippage occurs it can correct performance to help reduce loss of traction. I hope this helps.
LOCKTITE MAKES A SEALER FOR BUSHINGS ON DRIVESHAFTS. I WOULD IF I HAD DONE THIS JOB HAVE DOSED THE AREA WHERE YOU COULD SEE THE LIGHT GAPS WITH SOME OF THIS STUFF. ALL IN ALL A GREAT JOB. SORRY THE CAPS I HAVE REALLY BAD VISION.
Thank you, Ring up workshops the are close to you and price it up. Prices differ greatly depending on many variables including location, parts supplier etc..
Had both rear ones on my 320d done over a two year period. Labour on the rear left was about £60, rear right was I think about £80. Both done at the same garage. Rings were about £10 each and came with loctite. Did have to buy a new sensor after the first one was replaced, genuine BMW ATE make. Never any problems since
Due to the many emails I got about where to source the parts needed. I have now included a link in the description for Abs ring & sensor and also links for new rear driveshafts. I hope this helps you. Thanks to everyone for the kind words.
Hello, Thanks for watching the video. As I stated in the description, any driveshafts I bought were from my local supplier, they keep them in stock and I get 95% of my parts local. I put that up when I was asked to source one online. The company has sold 120 of them that can be seen (at this moment & they have a 3 year warranty) But I can't vouch for them as I never bought one. The price is right but if you are bothered maybe buy local too or contact them direct and see. I hope this helps
Thanks Gerard the video has been a big help I have bought 2 of these driveshafts and going do give them a try I got a quoted £80 to fit both driveshafts and abs sensors so hopefully this will solve all the issues I am having thanks
To add some longevity to your fix, I would suggest smearing some two part epoxy in the grooves and over the new ring you installed. Not only would it glue everything in place, but it would put a barrier to keep rust from forming since it would block the oxygen from reaching the place you just worked so hard to scrub free of scale and rust. I know this is a little late, since you assembled everything, but maybe it will give the next bloke a good idea before he starts his project!
Does anyone know if these reluctor rings are on the rear wheels only? I checked all 4 sensors on my X3 for damage but cannot see any kind of rings on the front side. Just the 2 on the rear wheel set.
Good video very helpful one thing I’ve done when changing these reluctor rings is boil the ring in cooking oil on the kitchen stove to expand it and it just drops over the cleaned driveshaft
Excellent video and explains it all clearly - many thanks! Proper old-school mechanic is the way to go as BMW dealer would have swapped out sensor first and once they realised it was this problem (the reluctor ring) their answer was to swap entire driveshaft with the new ring on it. Difference in cost over £1k!! Problem with this fault is that, until you get a solid fault (permanent warning lights) which logs the error to tell diags which wheel the problem is on, you get the annoying intermittent symptoms of DTC kicking in when it shouldn't, engine stuttering & losing speed etc. Great tip at end about spacer as a possible intermediate fix.
Thanks Rich
Thank you for sharing this with us!
The trick with the washer just saved me for now. The ring is bent on my X3 and damaged the sensor. Unfortunately 2 from the 3 guys at my local service are ill so they couldn't schedule the repair for this week.
I have tried puting a 1+1/2mm washer initialy, but that turned out to be too much. The lights went off as soon I did change the sensor but when I applied the breaks first time ABS just kicked in, then all the light come back, except the tyre presure one and the ABS was completely switched off this time.
I replaced the washer with a 1mm and that worked, so everithing works as expected for now.
Again, thank you for sharing!
i wish my mechanic was as good as this guy, he solved the problem in a very methodical and logical way.
Just replaced my reluctor rings after watching this video yesterday, followed what you said to do, I done both sides as I noticed the sensor in the side that didn’t have a fault was scratched so thought while I’m there I’ll get it done, thanks a lot even though I’m a qualified mechanic I still research every job I do, (depending on timescales). And if I can I like to watch a RUclips video as it gives you a good understanding and also heads up for what tools I’m going to need. Thanks Gerald
make videos
I am the same exact way. Even if I know how to do the job. Might have done it once or twice or even ten times before. Will like to go ahead and watch a video a refresh my self before every job lol.
What would it typically cost me to have a garage do this job on my 2009 3 series e90
I watched your video week ago .. done the job today testing the car tomorrow... let's see if it is fixed ... like you said try and fail rather than not try all all thankyou for posting this video appreciated
wat happened
The people who make the rings say you should heat the ring up so it slips over with very gentle taps then as cools shrinks for a permanent fit. You can also space the sensor back with a washer
Awesome video, clear and concise, thanks for sharing... I have an E91 2012 with 125K and this is a job that I will be tackling tomorrow if the rain stays off
Excellent Video. I like the way you have no plans of giving up at any time. Better to try than to not try at all.
I'm having exactly the same problem. I cleaned the ABS reluctor ring, and changed the ABS sensor (Already 3 times... Arghh!!!). I was planning on changing the full gimbals, but I'll try this method first... Let's cross fingers, I'll give you feedback ! Thanks for the video !
Syph3r- any news to what fixed it?
Very informative My car is in the garage at this very moment having both rings replaced. Having watched this video I am glad that I left the job for an expert to do.
Thanks for taking the time to write such a nice comment :)
Steve Hayward how much did you pay?
Thanks for your help, did it yesterday, first time taking driveshaft out, easy job thanks to you 👏, for £3 ring from eBay the car is fixed 😄.
Great 👍 well done
Would you tackle this job with jack stands?
Did it take a lot of heavy knocking? I am not built like Stallone!
@@suzesiviter6083done mine today was bashing it for ages gave up for a bit to have a sandwich and came back with a sledge hammer 3 wacks and it was out lol
Thanks for this. I completed this job this weekend.
👌💪💪🙌
Good stuff. I would put a light smear of marine grease round the shaft before tapping the ring on..
Better to try and fail than not have tried at all,
an excellent life motto.
Really good video thanks very much, another problem seems to be releasing the driveshaft nut. Great tip about fitting a washer to increase the spacing of the sensor slightly, thankyou.
Thanks for taking the time to comment, much appreciated :)
Thanks for taking the time to make this video. going to give it ago at the weekend.
Cheers David, best of luck
Thank you for taking time to share. I think I have the same problem and it's been very helpful.
Thank you for the comment.
Simular problem on my 318D 2011 model, TSC kicks in out of turns and sometimes on straights even though the conditions on the road is fine. (So the light is not on all the time like in this case) The repairshop here in Norway wanted 1200$ for the fix, they didnt mention if they would replace the entire axle or just the ring (Overpriced country, in every aspect)
Will try this fix when winter is over :) Thanks!
Super thankful for this useful video. Really helps me out...I hope.
This was a very real and practical video. Thank you 🙏🏾.
Thanks Curtis
just a note ABS rings are heated up wich exspand them,wich alow you to drop onto the drive shaft and you can place the drive shaft in a chess freezer if you have one wich shrinks the metal,
the only problem with that is if you got anti corrosion rings you will burn the corrosion coating!
Such a well detailed & clear video, with great advice. Brilliant !!
🙏
Awesome video I had A ABS problem traction kept engaging , 2008 BMW 328. The ABS ring was rusted like in the video so my car ABS kept engaging while I drive. I plug my OBE computer and it showed my sensor was reading incorrect wheel speed. I changed the entire axle. But doing what he did is much inexpensive and will work..
Another good video...you have far more patience than me..I always replace the drive shaft ..The price of the drive shaft and the price of the extra labour for the time cleaning and fitting ring probs works out the same
Just the video i needed, thanks Gerard.
Thank you.
My ring had snapped while I was driving luckily I checked them found that was the problem now I've just got to buy my new ring and do the job what you've done but mine is a Citroen Picasso front wheel drive so hope it is easy to get off as that one is thanks for the video great insight in to the abs system
Hi Gerard, thanks for the video. I had this problem last year on my E82 with a similar mileage to the E90, but sorted it by removing and cleaning the sensor. It returned again very intermittently last week whilst on the motorway so I'll try the washer route first, Thanks again 👍
Great video Gerard I have the same issue with my e87 and changed the sensor and the lights are off so hopefully that's it, but there was wear on the end of the sensor so I'll probably have to change the ring next but I know the process so thanks for that.
your welcome man, thanks for the comment
Thanks for sharing your info & taking the time to comment :)
Surely without any rust treatment it will corrode in 12 months? Maybe give it a light coat of paint. I’m trying the washer/shim method first. Good video thanks
Thanks for posting!
Not too short video, nor to long. Just enough to cover every detail. Perfect.
Would you recommend using a primer/anti corrosion of some sort over the bare metal before fitting the ring and placing it all back togheter, though? The bare metal would probably start rusting in just a matter of days after fitting it(?).
Yes I would recommend using an anti corrosion product for sure.
Thanks for your time mate, this video is more then helpful! Keep up the good work! :)
Great vid, thank you. Got this problem currently on my e92. How long did it take for the sensor to correct itself and the lights to go out when you test drove it?
way to go!!! love the persistance and can do attitude.
Thank you
Thanks for the video, however I can't understand why people make these videos without telling you the year, make, and model. Thing are different on each year and model
Very Useful Video, I am having the same issues with my E83 rear Reluctor and Sensors
Thanks for your great video. same issue. started with fuel pump, then to module then abs. turned out that it was the ring on the drive shaft. cost me £900 all in. 😞
Brilliant video thank you. Tried the washer trick but it didnt work. I can see the ring on mine is as bad as urs was. I've ordered a new ring and sensor and il be following ur video step by step to repair mine. Thanks very again.
The mighty Thor bangs the ring! Thnks!😋
Very great documentation. Keep up the good job.
Wonderful work, very nicely done. Thank you very much.
If you replace the sensor, put a washer just to give a bit more distance it should last longer.
Badly designed i have the same problem how much should a job like this cost? Great vid by the way.
Million Dollar tip regarding the sensor since ring catching the sensor as this is common reason for error on E90s.
Thanks for the nice comment
Thanks for sharing, very clear and helpful video really.
I had exactly the same issue, the mechanic installed washers which solved the problem temporarily, six months later the lights comes up again, I guess it need to put new rings and do the same job as here, I’m just wondering how much that will cost to do in Ireland?
Thanks again
I used kurust on the driveshaft reluctor ring down the sensor hole, fifteen minutes and cured. This will helo reduce speed of rust growth, I fitted a 1.5mm washer, test drove and got all sorts of faults from airbag to juddering brake pedal. Repeated with 1mm washer and car drove fine with only abs fault. Just need to drive car for enough miles to reset the light. Or did you have to use a reset tool?
My thoughts on this are, if the shaft is that old and crusty wouldnt you think its worth $60 for a new complete shaft that includes a new ring?
I agree Nathan, If you want to be certain of a fix it and it looks like this one, I would advise full shaft change. If you want to try it out on your own time and you don't mind failing, ya could save a few bucks as the ring is so cheap.
@Gerard Burke do you remember, how much miles/km you drove until the lights gone off, after you replaced the reluctor ring? I did the exact same same thing, before I saw your video, but the lights on my E90 are still on
Excellent video Gerard🙂
🙏👌👍
Really good video, this is something I'm likely going to have to do soon :D
Little tip from us.
Grease or wax up the ring it will prevent future corrosion.
We use Dynax UC wax before they get bad.
Works a treat and does NOT affect the magnetism or operation in any way.
It's a shame everything is assembled dry in the factory
@Jules75ZT
Is there a possibility that because i put a wire brush adaptor on end of the drill and put it in the sensor hole to polish the ring while turning the disc.. Fitted two new sensors .. But fault still is on. Have I polished the magnetic coating off the ring? Or is the abs ring magnetic all the way through? I think ive wrecked the rings thinking I was cleaning them through the hole 😢
What size is the hub nut socket 30mm or 36mm cheers
32
36 front i needed 32 rear
Hell of a video 👍
someone suggested push a washer between the ABS sensor and the ring to keep the gap again, do u recommend it?
Nice video. Very informative. Cheers
Gerard ,scan tool is saying rear right tooth missing but rear left looks just a bad , if left was also bad would scan tool say so or is it going to tell me after i fix the right ? do you know ?
Luckily I just found a rear left cv for 15$ brand new. Grabbing a right and going to just replace them both. Tired of fighting this damn abs situation. Washers on the sensors worked for about 2 weeks but now it's on, always.. Hopefully my sensors are still OK. They were new, but now I think they be scratched
Where did you get the reluctor ring? I found one UK based website but I'm having problems trusting them. My car has a different size depending on if it's automatic or manual (E46 330i) and they don't list which one they are selling, and they have a model in their line-up that doesn't exist, and E36 330i, so I don't feel comfortable buying from a parts dealer that has both missing and incorrect information on the same page.
Awesom video thx for Sharing.
I know this isn't the same vehicle, but I have a 09 128i (e82) and began receiving traction issues on the dash. The mechanic stated that axel and wheel sensor needs to be replaced. Does this sound right?
Really good explanation. Thank you!
This is such an awesome video, thank you.
I have a 97 E39 528i that has the abs light on too
I don’t have a tester so wondering if the sensors are only on the back wheels, or all four?
Great movie. But could you tell me if you connected the car to the computer in order to erase errors?Thank you for your response ;)
Not un my experience. Fault only clears when in motion.
Why didn’t you slowly use your press with lubrication ?
I have exactly the same problem with exactly the same wheel!! It must be a common problem with the same wheel!
Your thumbnail shows a toothed reluctor ring but your video shows the segmented one from a different driveshaft. Mine looks like it has an inner diameter of 72mm but that doesn't match anything online - any advice?
a bit desperate now sorry.
hi im haveing this same problem for about a month now would this make my engine light come on and my passenger light come on andthen stop the engine and not make it start agian ordo i have a more serious problem any help and advice would be most appreciated!!!!!! thank you 🙂
Hi, thanks for the great video. Are any special tools needed to get the driveshaft back into the wheel hub once the ring is changed, or is it just a bit of elbow grease?
Just bop it...
Any tips on changing the other side that has the exhaust pipe in the way. I can’t see how I can make space to get the driveshaft out.
The answer is yes, I showed replacement of driveshafts in a later video. I will post up a link when I get to my pc or just search my channel for BMW videos 👌
Great vid, thanks for sharing 👍
So replacing axel can fix my p1774 code? Please help i replaced sensor still got code maybe my abs ring is damaged i need new axel?
Nice video, thankyou
Do not I repeat do not do this. For 40 more dollars you can get an entire new axle with ring already installed
Fairplay man cheers for the insight
Clearly explained and very useful, thanks!
Have samw abs light when i removed the the shaft…there is no ring and it looks like abs sensor reads from bearing
Is this the same procedure as it would be on the e46 320d
thanks for the advice - precise and informative.
195k miles? Good effort!
Hi pal How did you determine which side needed the repair? Does it show you on the I computer deck which side was having the ABS problems?
You can do a visual check and see if anything is rubbing/out of round or use a scan tool capable or reading wheel speed sensors and simple road test or manually rotate wheel when jacked up and look at the live data.
What you where doing was well explained
reluctor ring is virtually the exact same design on my peugeot van, and its had a crack in it, so now and again would slip to an off angle and catch the hub and not spin, didnt matter when driving, but it was really important when braking! you approach a roundabout and then the pedal would start fighting you back! your slowing down for a slip road off the motorway and it goes into 3 wheel braking and tries to throw you off into the ditch...
epoxy glue fixed it..... some abs systems (and there all re-badged bosch really) (except the ones that are toyota) are more forgiving than others, being a van and a 2005 its really basic and forgiving of 'variation' i do not recommend that anyone reading this repairs with glue or non standard parts!
Great video very informative , I am having a issue with my 320D automatic when I put foot down from the 4th gear to fifth it struggles there is jerk sometimes or it’s says transmission fault on dash board , only it happens when my car is fully loaded with passengers or if it’s uphill, I took it to the Bmw they said it’s not transmission fault it’s the pick up ring on rear driveshaft it’s corroded and it’s swelled up so it’s touching ABS sensor and full driveshaft needs to be replaced, well I am thinking I can change the rings and get it fixed, what do you think Mr Expert? Thank you
Thank you for your kind words on the video, It is nice to hear feedback.
I replied to another man with pretty much the same issue as yourself. I will say to you like I said to him.
It all depends on how bad the corrosion is, then decide on if the repair of just the ring is worth it or not. I have done quite a few of these now and all of them have a lot of time to be invested to solve, In one case the repair was not successful, it was just gone too far. (none of them were the same)
When it is your own time it makes sense to go with the ring but when paying for labour it's probably makes more sense not too, unless the corrosion is in it's early stages (much better condition than in my video) The amount of time that's needed to get it right means it is cheaper/quicker to fit a shaft.
This job is very much a labour & parts combined issue, one has much more labour and small costing parts and the other is vise versa.
Depending on the quote they give for replacing the shaft I would say proceed, If they are way too high I would bring it to an independent workshop that's gives you better value.
Regards
Gerard
Is your egr valve plunging in and out ok? Judder from cold can be caused from that, use few drops of engine oil to lubricate. Really easy pop plastic cover and you will see.
Hi , your video has been very informative but , can you tell me what is the job/ purpose of the reluctor ring ?
The wheel speed sensor picks up the info it needs from this part.
It has hills valleys that magnetically interact with the sensor providing a series of pulses as they spin by the sensor. The computer looks for repitituous pulses.
Looping for someone in the Arena of Munich for help in the case.
Hi are there one reluctor ring on each side or just the drivers side? I have a e93 coupe and am about to buy replacements but want to know if theres one reluctor ring on each side so I have to replace one or two? Thanks...
hey i have also a e93 coupe, did you already replaced it?
what model is this car, because my 2007 bmw328xi doesn't have those rings on the rear ones , only have it in front.
Is it possible to paint over the part to stop it corroding soon again?
Does each wheel have one abs Reluctor Ring or one for front and one for rear wheel.Thanks
one in driver side and one right side passenger side !
Each wheel must have a pickup of some sort for the ABS/traction control etc.. varies for different makes and models. but in general these monitor all 4 wheels so if any slippage occurs it can correct performance to help reduce loss of traction.
I hope this helps.
LOCKTITE MAKES A SEALER FOR BUSHINGS ON DRIVESHAFTS. I WOULD IF I HAD DONE THIS JOB HAVE DOSED THE AREA WHERE YOU COULD SEE THE LIGHT GAPS WITH SOME OF THIS STUFF. ALL IN ALL A GREAT JOB. SORRY THE CAPS I HAVE REALLY BAD VISION.
Do you know what it's called?
Thanks 🙏 you saved me .
Thanks Jack
If i don't want to go through the effort of changing the reluctor ring, where can i buy just the end bit which you mentioned in the video. Thanks
I have put the driveshaft links in the description for you.
The cost for just the outer CV joint is not worth the effort or time, I looked into it and the job will take longer with no savings. links are above.
Hi dude, really helpful video. How much should this cost from a local garage (UK)?
Thank you, Ring up workshops the are close to you and price it up. Prices differ greatly depending on many variables including location, parts supplier etc..
Had both rear ones on my 320d done over a two year period. Labour on the rear left was about £60, rear right was I think about £80. Both done at the same garage. Rings were about £10 each and came with loctite. Did have to buy a new sensor after the first one was replaced, genuine BMW ATE make. Never any problems since
Due to the many emails I got about where to source the parts needed. I have now included a link in the description for Abs ring & sensor and also links for new rear driveshafts. I hope this helps you.
Thanks to everyone for the kind words.
Hi there just wondering if the driveshafts you put in the description are any good? Do they cause any vibration? Thanks
Hello, Thanks for watching the video. As I stated in the description, any driveshafts I bought were from my local supplier, they keep them in stock and I get 95% of my parts local. I put that up when I was asked to source one online. The company has sold 120 of them that can be seen (at this moment & they have a 3 year warranty)
But I can't vouch for them as I never bought one. The price is right but if you are bothered maybe buy local too or contact them direct and see.
I hope this helps
Thanks Gerard the video has been a big help I have bought 2 of these driveshafts and going do give them a try I got a quoted £80 to fit both driveshafts and abs sensors so hopefully this will solve all the issues I am having thanks
No problem, best of luck to you.
To add some longevity to your fix, I would suggest smearing some two part epoxy in the grooves and over the new ring you installed. Not only would it glue everything in place, but it would put a barrier to keep rust from forming since it would block the oxygen from reaching the place you just worked so hard to scrub free of scale and rust. I know this is a little late, since you assembled everything, but maybe it will give the next bloke a good idea before he starts his project!
Im trying to find the part number for a Reluctor Ring for a 2013 328i F30 Model - can't seem to find that - any idea? Would a E90 Reluctor fit this?
Hi Gerard. Would this fix apply to a 2009 E83 (X3) rear right?
What size socket is needed for the drive shaft nut and is it left hand or right hand thread. Cheers
30mm
Does anyone know if these reluctor rings are on the rear wheels only? I checked all 4 sensors on my X3 for damage but cannot see any kind of rings on the front side. Just the 2 on the rear wheel set.
thank you for throwing me into it :)
Good luck :)
hi what size size is the 12 point socket. please