I can't believe how easy you made that look.. I can almost guarantee I would have some sort of catastrophic failure if I tried that...😂 And I don't even own the bike yet.. I'm trying to find a dealership that actually has a 2021 CB 500 X... In georgia🇺🇸 great job..👍
Really nice clean job and very helpful video. Only thing, I'd change would be to pick up a bag of assorted heat shrink tubes (costs about a dollar at Harbor Freight). They can be cut to size and make a nicer insulating finish than electrical tape. Also worth it to spring for a shorter lightning cable for the phone, but I'm guessing you did that after posting the video. Thanks very much for posting.
szia! egy navit szeretnék ugyan igy bekötni csak nekem nincs meg ez a vak kábel, viszont ugyan ott megvan a fekete fehér, szerinted arra rá tudok kötni ?
Im not familiar with electrical system on this bike. What is that your installing to? I remember on my old cb300f I just installed it to the battery. I want to do it your way since I have a 2013 cb500f, and it looks much easier instead of leading through the tank from the battery , but before that I want to know what it is.
Hi, i like watching your videos and i know you had a CBF 125. Did you have any running problems with the engine? I have a 2012 with 21k km on the clock and im having a problem where on my first start of the engine the engine just stalls. I already did valves at around 19k km and that fixed it but im getting the same problem again. I did them today again since they were again a little over spec but after my first start after the valve clearence adjustment the engine stalled again after like 10 seconds. Did you have this problem or not?
Hi, i know this is an old comment but still. I have a cbf125 (also 2012) myself with 12k km's. I have never encountered this problem, just to let you know
Szia. Az en CB500F-em nehezen indul mikor a stand lent van. Kicsereltem a stand switch-et de a problema nem oldodott meg. Mikor fel van hajtva a motor tokeletesen indul. Ket kabel (zold es zold-feher) megy be egy 2x24 pines boxba. Gondoltam megnezem hatha ott van erintkezesi hiba. Nem tudod veletlenul hol van ez a box? Hi, when the kickstand is down on my CB500F the bike does not start smoothly. When the kickstand is up it starts straight away. I have installed a new kickstand switch but it didn't solved the problem. 2 cables are coming from the switch (green and green-white) and they are going in to a 2 x 24 pin junction box. I thought the contact problem could be there. Do you know where that junction box is?
Hmm, install is not the problem. What I'm wondering about is it connected trough it's own rele and/ or is it connected trough ignition (I think so) so it doesn't drain your battery during stops _ engine off. I guess the fuse is 5amps?
I’ve used those shitty connectors before and won’t use them anymore if they are exposed to the elements. I highly recommend soldering and heat shrink/wrap. Great vids.
...now this is an "installation" video (not like the heated grips video which was very basic). Fantastic steps on how to install...I gotta try it on my CB500FA soon.
►USB Charger: www.banggood.com/custlink/Dmm5TuU0NC
►Motorcycle products: www.banggood.com/custlink/vvDHuTU0AP
►Coupons: www.banggood.com/custlink/D3m83Kh5SJ
I can't believe how easy you made that look.. I can almost guarantee I would have some sort of catastrophic failure if I tried that...😂 And I don't even own the bike yet.. I'm trying to find a dealership that actually has a 2021 CB 500 X... In georgia🇺🇸 great job..👍
Still in the state of Georgia? I grew up there in Clarkston. Have so much fond memories.
Like your videos, can you zoom out to see the area of work before getting in on the close ups?
I think at 0:28 it needed a zoom out yes, otherwise it was good
I'm really starting to dig your videos about this bike man, you make everything look so simple and easy! Thanks bro!
I followed your tutorial, and I succeeded ! Thanks
Really nice clean job and very helpful video. Only thing, I'd change would be to pick up a bag of assorted heat shrink tubes (costs about a dollar at Harbor Freight). They can be cut to size and make a nicer insulating finish than electrical tape. Also worth it to spring for a shorter lightning cable for the phone, but I'm guessing you did that after posting the video. Thanks very much for posting.
Fully approuved on cb500f 2016
Thanks for the video I guess this would work on CB500X
Thanks for your video ... the link doesn't show the good charger on BG (yours is 2 usb, the link is only 1)
thanks very smart, straight to the point. I understood everything. wish there were more videos like this.
Does this work for 2022 model? Thanks for the helpful videos :)
Good video. I was just wondering why you didn’t get rid of all that excess wire?
Hello there
I have a cb500f 2014
And I need your help please
How can I contact you?
Dude your channel is amazing. Really thank you for all of this!
Thank you for this!! Finally someone do something the right way. 👍🏻
szia! egy navit szeretnék ugyan igy bekötni csak nekem nincs meg ez a vak kábel, viszont ugyan ott megvan a fekete fehér, szerinted arra rá tudok kötni ?
Very helpful video. Thanks a lot. My CB500F has two black tubed wires not one. Which one is to chose? Or will both work?
Im not familiar with electrical system on this bike. What is that your installing to? I remember on my old cb300f I just installed it to the battery. I want to do it your way since I have a 2013 cb500f, and it looks much easier instead of leading through the tank from the battery , but before that I want to know what it is.
This is the stock wire to connect a USB charger. This way it won't drain your battery. It works only on ignition.
@@zsinormotors Thank You
Hi, i like watching your videos and i know you had a CBF 125. Did you have any running problems with the engine? I have a 2012 with 21k km on the clock and im having a problem where on my first start of the engine the engine just stalls. I already did valves at around 19k km and that fixed it but im getting the same problem again. I did them today again since they were again a little over spec but after my first start after the valve clearence adjustment the engine stalled again after like 10 seconds. Did you have this problem or not?
Hi, i know this is an old comment but still. I have a cbf125 (also 2012) myself with 12k km's. I have never encountered this problem, just to let you know
Hola , te consulto de donde sacas corriente para el uso, puedo sacar del otro para faros auxiliares. No hay problema de usar esos,cables. Gracias
Szia. Az en CB500F-em nehezen indul mikor a stand lent van. Kicsereltem a stand switch-et de a problema nem oldodott meg. Mikor fel van hajtva a motor tokeletesen indul. Ket kabel (zold es zold-feher) megy be egy 2x24 pines boxba. Gondoltam megnezem hatha ott van erintkezesi hiba. Nem tudod veletlenul hol van ez a box?
Hi, when the kickstand is down on my CB500F the bike does not start smoothly. When the kickstand is up it starts straight away. I have installed a new kickstand switch but it didn't solved the problem. 2 cables are coming from the switch (green and green-white) and they are going in to a 2 x 24 pin junction box. I thought the contact problem could be there. Do you know where that junction box is?
excellent video and just what i was looking for, is the charger you fitted fully waterproof and have you tested it in heavy rain yet?
It can't be waterproof in the rain when in use.
hahaha nem os mecanicos da concessionária da honda tem esse cuidado todo
Thank you. I did this install on a CB500F from 2018 and it worked perfectly.
Hmm, install is not the problem. What I'm wondering about is it connected trough it's own rele and/ or is it connected trough ignition (I think so) so it doesn't drain your battery during stops _ engine off. I guess the fuse is 5amps?
Is it the same procedure for 2019 Honda CB125R ?
thanks for your video. I have a CBR 650 F 2017, do I also have this connection under the right fairing? Greetings from Germany
You should have put the charger head down incase if it rains, water 💦 won't get inside the charger.
How to know if my suzuki have this accesories install?
Would I have any issues hooking directly to the battery?
I’ve used those shitty connectors before and won’t use them anymore if they are exposed to the elements. I highly recommend soldering and heat shrink/wrap. Great vids.
Nice! thank you very much
Sehr informatives Video! Danke sehr.
What power fuse did you use, 2A?
Perfect - i did it the same way after i saw your demo - thx
Great recording, but it's easier to use the Option connector under the seat.
Very nice! Do you know how to install it on a CBF 600 SA (PC43)?
Does it catch the tank on full lock ?
great video
...now this is an "installation" video (not like the heated grips video which was very basic). Fantastic steps on how to install...I gotta try it on my CB500FA soon.
Excelentes videos
Crear videos
Seems only available on CB500 2016 and later.
True. I was trying to do it on my cb500f 2014 and there is no this wire. To author: could you suggest what to look for?
A perfect video
👏👏👏👍😊
uh, lo conecte director a la batería, hice mal? gracias por el video 👍
Mal rollo siempre tiene corriente. Mejor q lo corte la llave
Juan Antonio Gordo , gracias por la ayuda
Entonces esta perfecta la instalación que hizo este hombre?
@@xpit-bullx4283 , si yo se la copie y no tuve problemas, ahora espero sacar del otro cable energía para unas luces exploradores que compre.
Merci ! Ça marche sur un cbr 500r !
Tu sais sur quel fil la prise a été connectée ?
@BLUCKBUSTER j'ai fais l'installation, et non ma prise n'est pas alimenté lorsque la moto est éteinte c'est un fils apres contact
What’s your plan if it rains? Will it dry out and be fine or just not to ride in the rain?
Yeah that’s what I said too... I think the answer is installing the cube upside down rather than how it’s depicted.
Maybe that “cap” is semi water right. Maybe if he’s caught in the rain he’s just unable to use the USB’s.
Ian GlynWilliams yeah he could possibly just twist it till it’s upside down.