3D Printing Rapid PETG At 300mm/s On The Flashforge Adventurer 5M
HTML-код
- Опубликовано: 3 окт 2024
- Printing with PETG filament is now a whole lot faster! Elegoo sells rapid PETG filament for around $13 a roll and it can be printed at speeds up to 600mm/s. I'm going to test it out on the Flashforge Adventurer 5M 3D printer.
******************************************************************************************************
Flashforge Adventurer 5M Playlist: • Flashforge Adventurer 5M
Elegoo Rapid PETG Filament: amzn.to/3OFQxx6
Flashforge Adventurer 5M on Amazon: amzn.to/3OC06Nu
Flashforge Adventurer 5M Direct: shrsl.com/4ev0y
Warhammer 40K Bolt Pistol File: www.printables...
XXL Burger Press File: www.printables...
#3Dprinting #flashforge #elegoo
******************************************************************************************************
Coupons and Deals:
JLCPCB 3D Printing Starts at $0.30 & $54 Coupons for New Users Here: 3d.jlcpcb.com/...
Card Mafia: Use the Promo Code "FigureFeedback5Off" for 5% Off Your Card Mafia Purchase! : www.cardmafia.com?sca_ref=2492569.wSUwkQ9aSr
******************************************************************************************************
Socials:
Check out my other channel: / @jeremyhill
For business inquiries, email me at jeremy@figurefeedback.com
Follow on Threads: www.threads.ne...
Follow on Instagram: / figurefeedback
******************************************************************************
My 3D Printing Equipment (Affiliate Links)
Anycubic Photon Mono 4K: amzn.to/3odVEKT
Anycubic Wash and Cure 2.0: amzn.to/3pH41ii
Anycubic 3D Printing Grey Resin: amzn.to/3Wdv8xK
OnePeng Grey Model Resin: amzn.to/453cIDF
Anycubic Eco UV Grey Resin: amzn.to/45cB4ei
Siraya Tech Easy Grey Resin: amzn.to/3MyZCam
Mealos Silicon Mat: amzn.to/3pRJoAg
Gorilla Super Glue Gel: amzn.to/42c4TcA
Vallejo Model Air Set: amzn.to/3oTfGdP
Timbertech Airbrush Kit: amzn.to/3CbuuI0
Creality Ender 3 Pro: amzn.to/45dvGIe
Creality Rainbow PLA Filament: amzn.to/3WfYLP9
Inland Silver PLA Plus Filament: amzn.to/3BxpHQO
Inland Grey PLA Plus Filament 2-Pack: amzn.to/432tmSg
5:36 That looks like it would be a magazine :D Clips are a little different, they look like relatively thin pieces of metal that go inside a gun's internal magazine, and you push your cartridges in there, as opposed to pushing them into a detachable magazine. Once all your cartridges are spent and the last one is ejected, the clip ejects too, and you can then put a fresh clip in. Think of it as a paperclip, except it holds cartridges (the brass tubes that hold the bullets).
Sorry, I'm a 3D printing nerd too, but also a gun nerd :)
This is very cool by the way. I got some of this PETG too and I was kind of scared printing it at higher speed, but what I am getting from your video is that it is meant to be printed at these speeds, and probably should be. I appreciate you sharing your settings as not many folks do. Will definitely use that as a starting point for my rapid PETG and see how it goes. Btw I found that I got REALLY good quality at 220 if I am printing under 100, but I imagine that is probably not going to be often with this filament, as my printer can handle up to 500 :)
Great video brother, thank you for this useful info.
I'm printing with petg but not with rapid. I agree with your assessment. I keep my bed at 80 and my nozzle at 260 for the first 2 or 3 layers, then lower to 230. Seems to work well for me. I get beautiful prints. Petg is my new favorite filament. Keep up the good work. 👍
That’s some really great results. It’s good to know that I’ll be able to branch out to other filament types if my needs require something other than PLA with the 5M!
Just bought this filament because of your video - About to do my first print. Awesome demo and great quality vid. Liked & Subscribed my man. Looking forward to checking out more of your vids on the 5M.
I had some really good results from the orca slicer profile for regular petg. 255 nozzle temp running at 300mm/s inner walls and 200mm/s outer walls. This was on a handful of 25mm wide cable chain parts.
Thanks for sharing this video. I Just picked up some high speed petg+ from inland for $22. Never seen it before at microcenter. Hopefully works out never printed with PETG yet but your prints convinced me. They look sharp 👍
I just started printing with that EXACT filament as well and ran through most of the calibration settings/tests in Orca and found almost exactly the same thing. 250'C was too oozy and I had bad melting/warping and leaking from nozzle. 230'C felt a little too low for layer adhesion, but it wasn't bad. Overall, I'm at 235/85'C for first layer and 230/80 for remaining with pretty aggressive cooling turned up on overhangs and slowed down outer lines to 150mm/s and making sure to have slow down on curled perimeters to help with the warping / curling upward I noticed.
Smooth looking prints. I’ve been using the Elegoo Rapid PLA Plus and have been really happy with it.
I just ordered a couple of rolls. Can't wait to try it.
great results for sure. I was just wondering when someone would make PETG that was for high speed printers. Will have to check this stuff out. Thank you for doing this, very informative.
I got my Adventurer 5M (amateur? not the Pro model) a few days ago and I'm printing ABS on just by putting it inside a box. It's actually an old box that I was using to print ABS on my old Ender 3, but I think the box the Adventurer came in would be perfect - with the flaps opened up and taped together to make it taller. I cut a hole out of the back of the box so the printer still gets cool airflow to the electronics.
I sliced using Orca with the 5M Pro configuration (so it will allow me to choose ABS as the filament type).
It's working great.
I'm only doing it in my basement with an exhaust fan pulling air outside, and I don't hang around by the printer while its working - ABS fumes are nasty and probably carcinogenic. When the print is done I run down and take the box off of the top of the printer and run back upstairs and let it air out for 10 or 15 minutes before I go down and start taking the part off.
It's working great so far. I started out with small items to make sure the settings were acceptable - no stringing or extrusion problems - and now I'm ramping up to bigger parts and the only failed print I've had was with the stock textured bed. I put a Creality smooth PEI bed on it and it sticks incredibly well.
I am really happy with this printer. It is leaps and bounds a better thing than any of my old bed slingers.
Well done with your printer
Been using Elegoo's Rapid PETG for a couple of months now, and I've been printing it at 265 with a bed temp of 70 at speeds up to 500mm/s on my N4+, and this stuff does great. Just got a K1 Max this week, and have been using R PETG with it, and it has been even better! The stringing and quality was much better on the K1 Max. I love the Rapid PETG, and haven't really been using much else since you can get it at an amazing price! $45 for 4 rolls is hard to beat.
I noticed it says it’s marked down are their website, has it always been $13?
Yeah, that sounds about right@@kadensmith5586. The price usually hangs around $12-$15 depending.
I love printing with PETG!
glad to see you got good results, I tried petg a few days ago, calibrated it, started a print, about half way through it was going well, came back in the morning, and it was a disaster, holes in it, zits all over it, just terrible, this was on a p1p, so kinda of open like the flashforge, I feel confident it was user error.
I have the adventure 5m pro and bought 2 rolls of this petg to try after watching your video. Man the stuff prints nice!. I have my bed temp at 70s and printed some prints at 240c and 250c to see if i notice any difference.def a good buy! thanks..
Honestly, there's no other printer that even comes close to this one at that price tag. Keep em videos coming! Printing enclosure for it, would be good video idea.
That is a good idea. I saw someone designed some enclosure parts that just snap on without screws.
@@FigureFeedback Flashforge is releasing a kit for 30 bucks relatively soon! I'd save your money and try it when it releases!
Awesome results. I just ordered the same Adventure 5M you have a few days ago after a bunch of research on Core XY printers. Looks amazing for the price. I must say those prints look great. With most of the modified plastics like Easy ABS or PLA-CF for example, I've seen testing where it's not anywhere as strong as regular ABS or PLA. I wonder how the Rapid PETG will compare to regular PETG in some stress tests.
This stuff is great, Was $13 a roll on Amazon and printed way better than the stuff I was paying $23 for. Printed my first print with the mid range recommended temps and then my second print I forgot to change the temps so they were the normal Orca profile really no difference.
Love your videos. My rapid petg comes in today. I grabbed 2 rolls of black and 1 green to print my custom enclosure with. not sure if you have a video of it yet but since we talking petg an unclogging video would be great. Just had to clear a clogged nozzle and could only find 1 video of how to do it and since I’m only about 2 months into printing a better video would have been much more help and reassuring I wasn’t about to ….up my machine
Came here after finding out about Bambu Lab discontinuing PETG Basic, figured I'd try to upgrade to faster speeds since I need to print super slow rn.
What settings and stuff did you use? Got a couple rolls of this rapid petg to print my 5ms enclosure and I'm getting like under extrusion or something like that and despite taking measures like greatly decreasing print speeds
You guys have it so good in the USA. The filament cost twice as much in Canada.
Could you do a video printing with silk PLA? I'm really struggling with it on my 5m 😫
I printed a threaded bushing using this filament today.
This video is 4k that's amazing
Thanks great information. Cheap enough will give it a try for sure. Will be curios if it has the same robustness for Environmental issues. A while ago I left some PLA print in the car, lets say they didn't hold up well. I don't buy PLA any more after that, my prints are more for function then looks. Will be interested if you learn more.
I printed a birdhouse from this filament yesterday. I think that'll give me a good idea of its environmental resistance over time.
How about cooling? How much percent did you use?
We're on the same journey with our new 5Ms except I'm about a week behind you! Are you planning to try printing TPU? That's the next filament type on my list
Yes, I am planning on getting some TPU to try out.
What are your PETG support settings for this? i cant seem to get them right. it either doesnt support at all or it fuses to the print.
Thanks for the video, did you use the bed wich come with the machine or another one? Many thanks
Price went up to $27.99… still a decent deal
Has anyone tried printing the 5M enclosure with this filament?
Orca slicer can print direct to flash forge adventure 5m, I’m doing it as we speak
I know that PETG is indicated for parts of the enclosure, but I'm printing all the parts with PLA. Am I making a mistake? What do you think? You mentioned that you printed PETG at 235c, but temp did you set your bed at?
I'm having trouble printing my enclosure with PETG on my adventurer 5m. At first it was oozing so i turned it down to 245 and that helped with the oozing, but it is having so much trouble with the supports. They aren't sticking and then the nozzle runs through the filament sticking up from the supports and gets covered in filament. This is causing the guards to look bad as well. Since its printing everything except the supports correct do i just change how the supports are printing? Only a week into printing, just looking for some suggestions.
Mine prints PETG way better in the 275 range with Normal PETG not the high speed stuff
Some e-coli in that burger press
In another comment here you replied "The only thing I changed were the bed (80 degrees) and nozzle temperatures (235 degrees). Everything else was left on default with Flashprint and Orcaslicer."
Which default profile did you use? I cannot find anything for rapid PETG in Orca. I apologize if you mentioned this somewhere else and I missed it. I am using the 2.0.0 full release.
You're right, there is no profile for rapid PETG. What I meant was I used the default PLA profile and just changed the nozzle and bed temperatures of that profile.
@@FigureFeedbackGotcha, thanks! Was that the default HS-PLA or or the non-rapid one?
i dont have a preset for high speed petg where can i fing a .cfg?
print a temperature tower
any chance you could throw up a printer profile for the petg?
The only thing I changed were the bed (80 degrees) and nozzle temperatures (235 degrees). Everything else was left on default with Flashprint and Orcaslicer.
When you say 300mm/s is that inner and outer walls? Orca defines both speeds. I tend to print faster inside then on the outside by +50mm/s on my Neptune 4.
300mm/s would be for the inner walls and 200mm/s is for the outer walls in Orca. I'm not sure if it's the same thing in FlashPrint since it only shows a base print speed of 300mm/s in that slicer.
@@FigureFeedback thanks! Yeah I bought 2 of the PETG rapid! Excited to try it out!
Just bought 4 rolls for $40
Sweet deal!
Magazine, not a clip. 😂
Yeah I don't know much about guns.