Do you think the CRZ shifter box would be a direct bolt in fit even with the oem Fit shift cables? I’m looking at alternate shifter options for my factory manual Fit
I might have missed it, but what water pump housing, water pump, alternator, etc. do your run? I do know I need an EP3 or aftermarket idler where the PS would go
The water pump is stock but the plastic thermostat housing and thermostat are from the first gen crv 02-06 crv the alternator I believe is from an accord. You just need it to match whatever alternator plug you have
@@KevronsEye so you are running stock, TSX accessory mounts? I’m putting a K24A JDM swap in mine, which I’m pretty sure the water pump housing and accessories are all different and won’t work. Just trying to figure out which USDM model I can get them off of and have everything clear.
@@adamclemmons1193 yea all twx stuff. You’ll definitely need to switch them if it’s a jdm motor. But I haven’t done that so I’m unsure what will work on the jdm engine
So I have lots of questions because I’m in the middle of possibly k swapping my 2010 Honda Fit and I just want to make sure I’m getting the right parts as my fit and yours seem to have similar engine bays and ect.. get back to me when you can. Much appreciated
vCloudsHD Hey thanks for watching and asking questions!! Unfortunately the 09-12 is a different mount kit and wiring etc. It is a different swap. I’d love to do. 09-12 in the future. My brother an I have talked about it a lot. I’d check out Hasport for all of the info you will need!!
@@KevronsEye would love to go k20 with my fit as well but mines is a 09 as well and it's rhd out of Japan just reading where u said the mounting kit is a lil different had hasport has not yet made the mounting kit for the 09 would it be a diy or the is already available and what are some tips u can offer as well bro .
Nice,just a pair of question Crz Shift box with 2008 civic si shift harness? Axle from hasport? Thx Im swapping my 03 jazz,but in europe more piece are differenti
So I used a Honda 2011-2012 CR-Z 6spd manual shift box and then I used the 2012-2015 civic SI shift cables The axles are from a Base model 2003-2006 RSX or the 02-06 civic SI axles.
I watched another video and noticed he notched the passenger side frame rail, the k-frame and even the electric power steering. did you have any issues that required that?
We didn’t have any issues with anything touching other than the trans area that we notched. I know what video your talking about. I do k ow that a few people have had issues when they used the innovative mounts with the hasport mounts that the pass side did need to be shaved down as the a/c pulley was just touching. My brother and I have used Polly filled oem mounts and had no rubbing issues
Can you give some of your thoughts on suspension tuning? I'm buying a 2010 that needs a full refresh and I'd like to put something on that will make the handle better to so it's ready for a future k swap.
Hey man I’m swapping my fit here soon and your videos are a blessing I’m able to plan ahead but I was wondering if there’s a chance you could give me a list of everything you needed?
Maled1cted not that I know of. The frame on the fit’s are different from manual cars and auto cars. Also there are no mount kits for automatic K series available that I know of.
The stock Fit cables are to short to use on a K series transmission The shifter mechanism is on the back of a The Fit transmission and it’s on the front of the K series We’ve cut and welded K series cables before. It works but is a pain to do and not worth it when off the shelf stuff works
@@KevronsEye Im sorry about not specifying, i wasn't talking about the cables i was talking about the actual shifter rod on the shifter box since the CRZ one has an S bend that leaves it in a funky location. You can try cutting the shifter rod before the S bend and just weld on the fit shifter rod so the shifter is straight up and down. Ive done this before with success on a foxbody with a t56.
R O I get 26 in the city. And that’s me just ripping around not trying for good mileage. So I don’t see a problem getting 30mpg. You can shift all day long at 2-3k and still have loads of torque. I took off in 3rd the other day and barely noticed haha.
Hello good afternoon brother. I also live in Michigan. I'm about to start my project. Swap k24z7 from a 2012 civic si on my 2008 fit gd3. Could you help me with a list of parts that I need to do the swap or if you have some spare parts that you want to sell, please let me know. I've written you on Instagram but you haven't seen my messages.
I have not used that engine/transmission before. That year is more ideal for the 2009-20013 GE Honda Fit. The wiring and sensors are different, The engine and transmission mounting is different. It'd be easier to use a engine and transmission from 2008 and back.
@@JeissonParra-z6h The engine side will work but the transmission side and rear bracket are different mounting style on the 09 and up engine transmissions
Check out part 4 here! ruclips.net/video/bZ_g-bEyYYo/видео.html
Great video!!, now im swapping k24 engine in changan car, all people says is imposible but i see this video and now i know is possible
How it is for the driveshaft till now？
Many respect for doing the video. amazing work
Holding up great. I have about 20k on the swap with no issues
I need this in my life...
Awsome, any 2nd Gen Fit experience or suggestion?
Coil I hire you to do the swap on my fit?
Can’t wait to see some more footage
Thanks, excellent video.
We've got our shifter box adapter - first gear *WHAP*
Second gear *POW*
Third *PACHaNG*
Fourth *SLAM*
Fifth *CHOKESLAM*
Sixth *CASUALMURDER*
And, reverse.
Do you think the CRZ shifter box would be a direct bolt in fit even with the oem Fit shift cables? I’m looking at alternate shifter options for my factory manual Fit
The factory fit cables are to short to work with the K series transmission
I might have missed it, but what water pump housing, water pump, alternator, etc. do your run? I do know I need an EP3 or aftermarket idler where the PS would go
The water pump is stock but the plastic thermostat housing and thermostat are from the first gen crv 02-06 crv the alternator I believe is from an accord. You just need it to match whatever alternator plug you have
@@KevronsEye so you are running stock, TSX accessory mounts? I’m putting a K24A JDM swap in mine, which I’m pretty sure the water pump housing and accessories are all different and won’t work. Just trying to figure out which USDM model I can get them off of and have everything clear.
@@adamclemmons1193 yea all twx stuff. You’ll definitely need to switch them if it’s a jdm motor. But I haven’t done that so I’m unsure what will work on the jdm engine
@@KevronsEye gotcha. As always, I appreciate the insight.
Can I use a tsx ecu and engine harness
Yes that is what I’m running
@@KevronsEye can you make a parts list of everything that's needed
Just curious: Have you had any issues using the cups those axles came with (no swapping)?
So I have lots of questions because I’m in the middle of possibly k swapping my 2010 Honda Fit and I just want to make sure I’m getting the right parts as my fit and yours seem to have similar engine bays and ect.. get back to me when you can. Much appreciated
vCloudsHD Hey thanks for watching and asking questions!! Unfortunately the 09-12 is a different mount kit and wiring etc. It is a different swap. I’d love to do. 09-12 in the future. My brother an I have talked about it a lot. I’d check out Hasport for all of the info you will need!!
@@KevronsEye would love to go k20 with my fit as well but mines is a 09 as well and it's rhd out of Japan just reading where u said the mounting kit is a lil different had hasport has not yet made the mounting kit for the 09 would it be a diy or the is already available and what are some tips u can offer as well bro .
sorry if this was asked already, what are you using for headers? tnx
dadjujus I have a video coming out shortly that will be covering header options!!
Nice,just a pair of question
Crz Shift box with 2008 civic si shift harness?
Axle from hasport?
Thx
Im swapping my 03 jazz,but in europe more piece are differenti
So I used a Honda 2011-2012 CR-Z 6spd manual shift box and then I used the 2012-2015 civic SI shift cables The axles are from a Base model 2003-2006 RSX or the 02-06 civic SI axles.
@@KevronsEye thanks!!
What motor mounts
I watched another video and noticed he notched the passenger side frame rail, the k-frame and even the electric power steering. did you have any issues that required that?
We didn’t have any issues with anything touching other than the trans area that we notched. I know what video your talking about. I do k ow that a few people have had issues when they used the innovative mounts with the hasport mounts that the pass side did need to be shaved down as the a/c pulley was just touching. My brother and I have used Polly filled oem mounts and had no rubbing issues
@@KevronsEye thanks!!!
Would the civic si cables work t
With the fit box... looking at the hybrid racing option and they make both for the fit and the crz.
No they don’t work on the fit box. You’d want to use the CRZ version witch still would need to be modified to fit the si cables
Are those the same Honda fit hub?
Sophia Morrison Wesley The knuckle and hub are factory parts from the 07-08 Honda Fit
@@KevronsEye okay thanks..
If you choose a Honda Fit with a manual trans, can you use the.fit shifter cables or do you still have to custom fit it?
You can’t use the stock fit cables at all they are to short and won’t reach
Can you give some of your thoughts on suspension tuning? I'm buying a 2010 that needs a full refresh and I'd like to put something on that will make the handle better to so it's ready for a future k swap.
I would definitely check out BC racing and TCS Automotive. They can help a ton!!! Thanks!!
Hey man I’m swapping my fit here soon and your videos are a blessing I’m able to plan ahead but I was wondering if there’s a chance you could give me a list of everything you needed?
I’m working on getting a full parts list together
@@KevronsEye you got list part. Im planning to kswap my chevy volt.
@@KevronsEye Any chance I could bug yah for the parts list?
Have do ur swap
What axels did you use
You can use civic EP3axles, that's what i did
And the accord intermediate shaft?
@@AllABOUTTHEBOOST No i used the K20 intermediate shaft you cant use the accord one without custom axles
Any updates on the axles without swapping cups?
I haven’t had any issues with them yet!!
Hi. Is there a way to swap k20a2 with AT ?
Maled1cted not that I know of. The frame on the fit’s are different from manual cars and auto cars. Also there are no mount kits for automatic K series available that I know of.
Do you have the part number for the axles you used? My plans are going k24a any input on that also?
Axle part numbers are HO-8186 and HO-8187 k24a is the same engine that i'm ruining, it should be a blast!
@@KevronsEye thank you so much, can't wait for your video on the wiring routing. It's very helpful your vids so far.
@@KevronsEye hi, how about the intermediate shaft what do you use?
@@figisudiman1121 you can use any k20 manual transmission intermediate shaft. So civic si 02-08 and rsx 02-06. And even 02-06 crv manual trans only
@@KevronsEye oh ok thx alot
You guys could just cut and weld on the shifter rod from the fit shifter to get it to line up in neutral how it should.
The stock Fit cables are to short to use on a K series transmission The shifter mechanism is on the back of a The Fit transmission and it’s on the front of the K series We’ve cut and welded K series cables before. It works but is a pain to do and not worth it when off the shelf stuff works
@@KevronsEye Im sorry about not specifying, i wasn't talking about the cables i was talking about the actual shifter rod on the shifter box since the CRZ one has an S bend that leaves it in a funky location. You can try cutting the shifter rod before the S bend and just weld on the fit shifter rod so the shifter is straight up and down. Ive done this before with success on a foxbody with a t56.
@@thewraith6360 ahh yea I gotcha now. Yea I’ve done that before in the past too. I may look into it since the car is put away for the winter
Cómo poner seguro ala cajuela
Super dope 👏🏼🔥
Where is the list for honda fit k swap
I don’t know I haven’t seen a full list anywhere
@@KevronsEye can u give me everything u use for ur k swap fit im
Doing mine
@@JoseRivera-on2ol you can watch the videos i tell you everything I used
@@KevronsEye the only thing missing is the motor mount u use
@@JoseRivera-on2ol I mentioned I’m using the Hasport mounts The only company that makes mounts for a K swap Fit
Hows the gas mileage?
R O I get 26 in the city. And that’s me just ripping around not trying for good mileage. So I don’t see a problem getting 30mpg. You can shift all day long at 2-3k and still have loads of torque. I took off in 3rd the other day and barely noticed haha.
Hello good afternoon brother. I also live in Michigan. I'm about to start my project. Swap k24z7 from a 2012 civic si on my 2008 fit gd3. Could you help me with a list of parts that I need to do the swap or if you have some spare parts that you want to sell, please let me know. I've written you on Instagram but you haven't seen my messages.
I have not used that engine/transmission before. That year is more ideal for the 2009-20013 GE Honda Fit. The wiring and sensors are different, The engine and transmission mounting is different. It'd be easier to use a engine and transmission from 2008 and back.
@ ok. so i won't be able to use the hasport mount with the k24z7?
@@JeissonParra-z6h The engine side will work but the transmission side and rear bracket are different mounting style on the 09 and up engine transmissions