that was a high quality video! I was wondering how only 3 mosfets manage the transition between the 3 phases of the motor, an explanation of the circuit would help, thanks.
@@abraxasivo yeah im not convinced...lots of dudes these days are just getting click bait,, that schematic makes no electrical sens and does not show input or output connections so it looks like it just is going in circles..
leyendo los comentarios y una respuesta que diste acerca del cable rojo que pusiste en el común donde se juntan las tres bobinas y dijiste que habias convertido de delta a estrella... te cuento que estos motores siempre están en estrella y que para que estén en delta debías desunir las tres bobinas y sacarlas del común y uniéndolas cada una con el extremo de la otra obtienes la conexión delta... traducción: reading the comments and an answer you gave about the red wire you put on the common where the three coils meet and you said you had converted from delta to star... I tell you that these motors are always in star and that for them to be in delta we must separate the three coils and remove them from the common and joining each one with the end of the other you get the delta connection...
Actually you are right this motor was star type connected, I just added the red wire as common connection. Your answer made me think a lot, but you are right, thank you👍🙂🤝
لو أنك صورت ما فعلت داخل الموتير من توصيل الملفات واخراج الشريط الاحمر لحصل النفع بشكل اسهل عملت الدائرة واوصلت الاشرطة كما فعلت انت ولكن لم تعمل لو انك تعيد تصوير هذا الفيديو بشكل اوضح ولك الشكر
reading the comments and an answer you gave about the red wire you put on the common where the three coils meet and you said you had converted from delta to star... I tell you that these motors are always in star and that for them to be in delta we must separate the three coils and remove them from the common and joining each one with the end of the other you get the delta connection...
The voltage probably depends on the motor, and the direction is determined by the resistors and diodes. The motor should only run in one direction. To reverse the direction 3 diodes need to be swapped with 3 resistors and installed in the proper orientation.
Der Schaltplan sollte noch einmal überdacht werden. Der einzige Anschluss ist "GND" (Ground). Es gibt keine Motoranschlüsse und auch keine positive Spannungsversorgung. Man sollte schon auch das zeichnen was man lötet... Grundsätzlich finde ich es aber super, wenn ein Schaltplan gezeigt wird! Es gibt hier bei RUclips viele Beispiele ohne einen Schaltplan - leider!
Tengo un motor de ventilador de aire acondicionado invertir, dice que consume 35 wats y el voltaje en la etiqueta es de 310 voltios. Este control podría servir para hacerlo funcionar? Alguna sugerencia?
Ercan ustam bunu çay toplama makinelerinin motorunu güçlendirmek için kullanmak istiyorum. 24 dc küçük motoru var. Üç çıkışlı onu dört yaptım. Kendi sürücüsünü iptal ettim sarımı bayağı kalın olmasına rağmen çok zayıf kalıyor sürücüden olduğunu düşünüyorum. Yanlız gelen voltaj 24 volt ne yapabilirim? Biraz bilgi versen ülke ekonomisine büyük katkı olacak bizde yolumuzu bulacağız İnşallah. Bir sürü atıl cıhaz var kullanamamışlar.
Excelente video ,,estaba buscando fabricar un controlador de un motor de overboard casero ,,ya que aqui donde vivo no venden controladoras comerciales ,,,y la unica opcion es fabricar una casera como la que muestras en el video ,,la duda que tengo es servira para poder hacer un scooter electrico casero con un motor de overboard ? ,,y la otra duda es cual es el rango de voltage y amperaje con el que se le puede alimentar a este controlador casero ,,agradezco mucho si respondes mis dudas ,,,saludos desde el salvador
Ok i think i sussed it out the red wire goes to the center of the star wiring it has to be added separatly ,but he doesnt tell you that ,it is possible some bdlc motors would require being changed to star wiring arrangement if they are different,
this isnt a circuit id recomend for scooter or ebike as it will be extremely noisey ,like load wineing as spinning up,and will be bit jerky and erratic,due to lack of hall sensors for rotor position, but as a fail safe ,it be ok \
Direct from Marituba, Pará Brazil thanks for the video, I would like to know if this controller is the battery or if it is connected directly to the electric grid? I would like you to make a 48 v14 Ah battery model is it possible? From also
@@ErCanEverything I would also like to know, friend, how many amps can I get from this circuit? Would it be possible to move an electric bike motor, for example?
I'm watching from Russia. Well and qualitatively done! Simple and clear! Respect to the author! But, I'm not very good at electronics. Therefore, the author, please tell me where the INPUT and OUTPUT to the motor are in the scheme?? . Смотрю из России. Хорошо и качественно сделано! Просто и понятно! Респект автору! Но, я не очень силён в электронике. Поэтому, автор подскажи пожалуйста, где в схеме ВХОД и ВЫХОД на мотор??
hola exelente elvideo de montaje voy a hacer el circuitopara ver si funciona por que lei muchos que no creen y no esplican por que ademas pretenden manejar un auto electrico o jumbo jet con un circuito de experimmentacion exito y salud
How did you manage to get your power in if it a three phase delta ànd it only three cables coming out as your supply output feed or load, May I know your positive input then ??????
I've made it like this but it doesn't want to play, why? the motor is locked, it won't move. used motorcycle photocopy diameter 6cm 12pole stator 10 pole rotor
The motor must have 4 cables, 3 phases and one common cable that connects to the positive. If you connect in this way then there is a burned out transistor. Try starting with a lower voltage of 8V. Because my transistors burned several times because I was trying to start with 15V. Once it starts, you can increase the voltage to 20V. But this video is a test only
@@ErCanEverything I've tried it using an adjustable 8v dc voltage MAGICAL transformer, the motor will spin and I raise the voltage again to 15v rpm and it reads 5000 very strong power. Strangely, I tried using the 12v DC drill battery again, it wouldn't spin and the motor locked, but when I used the transformer at 4000rpm while the supply was rotating, I replaced it with a drill battery, the motor kept spinning and the power was stronger. How can that be explained? Thank you!
When the transistor fails then it locks the motor. With disconnected motor measure with a multimeter there must be no short circuit between the pins of the transistor
Hall sensors are in place but I have not connected them and there is no additional controller. But I connected 1 extra cable to a common point of the three cables, this red cable goes inside the motor and is connected to a common point and that's.
Hello something doesnt add up here where is the red -positive wire connected to under the motor, as you conveinently hiding it from view ,as normally bdlc motors only have ,yellow/green/blue ,phase wire , So we ask you, Where is the red wire connected , if you dont answer ,we will asume fraud and seek demonizing
I connected the red cable inside a common point of the motor, changed it from delta to star type connection but it can now be used both ways. This controller only works with common point motors.
@@ErCanEverything How a normal bicycle hub motor can have a common point of star connection? Is there any provision that the circuit also work in delta configuration as well?
Im looking for the same, but i think that you will not be able to controle it properly due to not having pwm input. And im not sure but i read that it cant go 0 rpm so is useless.
that was a high quality video! I was wondering how only 3 mosfets manage the transition between the 3 phases of the motor, an explanation of the circuit would help, thanks.
Note that he connected to AC power. You can look up AC 3 Phase Induction Motor.
He's creating some kind of phase manipulations to get the 120 degree difference between phases..
No way, fake
@@abraxasivo yeah im not convinced...lots of dudes these days are just getting click bait,, that schematic makes no electrical sens and does not show input or output connections so it looks like it just is going in circles..
hello friend, where can I get the positive wire of the hoverboard motor, this circuit was made for him, correct?
leyendo los comentarios y una respuesta que diste acerca del cable rojo que pusiste en el común donde se juntan las tres bobinas y dijiste que habias convertido de delta a estrella...
te cuento que estos motores siempre están en estrella y que para que estén en delta debías desunir las tres bobinas y sacarlas del común y uniéndolas cada una con el extremo de la otra obtienes la conexión delta...
traducción:
reading the comments and an answer you gave about the red wire you put on the common where the three coils meet and you said you had converted from delta to star...
I tell you that these motors are always in star and that for them to be in delta we must separate the three coils and remove them from the common and joining each one with the end of the other you get the delta connection...
Actually you are right this motor was star type connected, I just added the red wire as common connection. Your answer made me think a lot, but you are right, thank you👍🙂🤝
+ from the engine from where who??
This motor is a star type, and inside there is a common point of V U W, and I connected this red wire there. Otherwise the circuit does not work.
And a circuit diagram should include power in, POT and power output
Useles without clear circuit diagram.
hello thanks for the video, can you also make one with 80A or at least 60A (for continuous operation)?
You can probably make it your self by using higher rating components, but am not sure gow efficient will be
لو أنك صورت ما فعلت داخل الموتير من توصيل الملفات واخراج الشريط الاحمر
لحصل النفع بشكل اسهل
عملت الدائرة واوصلت الاشرطة كما فعلت انت ولكن لم تعمل
لو انك تعيد تصوير هذا الفيديو بشكل اوضح ولك الشكر
is it returns current product
Dose it work 5v to 48 v sir
Sir I want some details to this how much volts and amps taken by Multimeter test video to your channel 🙏🙏🙏🙏🙏
reading the comments and an answer you gave about the red wire you put on the common where the three coils meet and you said you had converted from delta to star...
I tell you that these motors are always in star and that for them to be in delta we must separate the three coils and remove them from the common and joining each one with the end of the other you get the delta connection...
Isso é uma vergonha.. a pessoa não tem a intenção de ensinar.. aonde está o cir uito esquematico. Bloqueam o video..
Very good give me cicuit diagram and past list please
Everything is written in the description and the circuit diagram is at 2:10
nice job!!!
i have one question, it can go backwards?
Super!
This BLDC Motor is Star Connection, if IDelta Motor, then how can I use this your designed Controller?
اتجاه الدوران لايحدد بهذه الطريقه ممكن يذهب يسار او يمين لان السنسر ملغات ثم لم تقول مصدر التجهيز كم فولت 6 فولت او 12
The voltage probably depends on the motor, and the direction is determined by the resistors and diodes. The motor should only run in one direction. To reverse the direction 3 diodes need to be swapped with 3 resistors and installed in the proper orientation.
Just what I needed, thank you so much!!
is that red wire from motor a nuetral winding then suplied positeve and to the board is negtive?
Could you please share the circuit diagram. How do you connected the power supply in this circuit?
Good but motor dayrection not right
Can i use 25Amp n channel smd mosfets??
Of course, but you have to put a heat sink.
If you want them to be more durable, you can connect additional transistors in parallel.
Sobre o fio vermelho tem que ser dentro do motor ou tem como alimentar o circuito nos mosfet
Der Schaltplan sollte noch einmal überdacht werden.
Der einzige Anschluss ist "GND" (Ground).
Es gibt keine Motoranschlüsse und auch keine positive Spannungsversorgung.
Man sollte schon auch das zeichnen was man lötet...
Grundsätzlich finde ich es aber super, wenn ein Schaltplan gezeigt wird!
Es gibt hier bei RUclips viele Beispiele ohne einen Schaltplan - leider!
Amazing video I have tried and it worked now my question is why the mosfet get hot?
MTBF: 5 minutes.
backside wiring of PCb is absolutely eye blinding. It makes one crazy
Please Circuit Design link please
Benzer videolarda mosfetler için soğutucu kullanılmış, sizce gerek var mı soğutucu kullanmaya ?
holy muscle Batman! I was expecting a hard-drive or DVD brushless motor but you hooked up an electric vehicle even with a wheel!!! 😲
Didn’t expect that too
FAKE FALSO SE NECESITA UN CONTROLADOR SI NO NO HACE LA CONMUTACION DECLOS POLOS NO ENGAÑEN MAS
Very Nice 🇧🇷 top ESC motor brushless
Tengo un motor de ventilador de aire acondicionado invertir, dice que consume 35 wats y el voltaje en la etiqueta es de 310 voltios.
Este control podría servir para hacerlo funcionar?
Alguna sugerencia?
Greetings from Colombia, do you have a diagram or a video to make a 3000w 80A card for a brushless motor that has forward and reverse gear?
40 A no heat sink?
Is it possible to use any N-channel mosfets? 75N75 for example.
Mine are also N channel MosFet's🙂
Hello, could you help me, I want to repeat your controller, but on IRF1404 transistors, please tell me which circuit components to take in my case?
You can use absolutely the same scheme, the transistors are identical, even yours are more powerful🙂
Una pregunta cuanto es el voltaje de entrada
Ercan ustam bunu çay toplama makinelerinin motorunu güçlendirmek için kullanmak istiyorum. 24 dc küçük motoru var. Üç çıkışlı onu dört yaptım. Kendi sürücüsünü iptal ettim sarımı bayağı kalın olmasına rağmen çok zayıf kalıyor sürücüden olduğunu düşünüyorum. Yanlız gelen voltaj 24 volt ne yapabilirim?
Biraz bilgi versen ülke ekonomisine büyük katkı olacak bizde yolumuzu bulacağız İnşallah. Bir sürü atıl cıhaz var kullanamamışlar.
No explica a cuántos voltios?
The voltage your feeding inn, is it AC or DC
👍👍👍👍👍🌹🌹🌹🌹🌹🌹
Please! Esc 350w, 500w? Next video!
6 MOSFET?
puedo usar hn75n09ap ??
New here. Great Video! Looking for a sensorless BLDC 3 phase motor controller for a 12 volt 850 watt motor? any plans / pc boards I can try to build?
🇧🇷Here in Brazil. Very good your project. How many amps does it support, can it run a washer and dryer motor for testing?
In principle, it is possible, but the motor must have 4 cables, not 3
Bunu nasıl 200a yaparız
Excelente video ,,estaba buscando fabricar un controlador de un motor de overboard casero ,,ya que aqui donde vivo no venden controladoras comerciales ,,,y la unica opcion es fabricar una casera como la que muestras en el video ,,la duda que tengo es servira para poder hacer un scooter electrico casero con un motor de overboard ? ,,y la otra duda es cual es el rango de voltage y amperaje con el que se le puede alimentar a este controlador casero ,,agradezco mucho si respondes mis dudas ,,,saludos desde el salvador
Ekstra,👋
Ok i think i sussed it out the red wire goes to the center of the star wiring it has to be added separatly ,but he doesnt tell you that ,it is possible some bdlc motors would require being changed to star wiring arrangement if they are different,
this isnt a circuit id recomend for scooter or ebike as it will be extremely noisey ,like load wineing as spinning up,and will be bit jerky and erratic,due to lack of hall sensors for rotor position, but as a fail safe ,it be ok
\
Direct from Marituba, Pará Brazil thanks for the video, I would like to know if this controller is the battery or if it is connected directly to the electric grid? I would like you to make a 48 v14 Ah battery model is it possible? From also
This circuit works from 8 to 20V
@@ErCanEverything This circuit works from 8 to 20V but I would like to know if it is DC or DC/?
@@ErCanEverything I would also like to know, friend, how many amps can I get from this circuit? Would it be possible to move an electric bike motor, for example?
DC
@@boasnovasonline8764 To drive an electic scooter you need another circuit controlled by the MCU. This is a prototype and will not run at full power
Fake video
hola, muy buen video,con que rango de voltaje trabaja
The hall sensors are functions?
Not without hall sensors is connected
hello men, wich is the current voltage? and friend how you take the common point into the motor? many thanks for you
El circuito solo sirve para probar un motor. El regulador nunca baja a cero RPM.
There are many channels with this same circuit.I tried this many times with many little changes But it doesn't work at all. Ufff..😓😓😓☹️☹️
I'm watching from Russia.
Well and qualitatively done!
Simple and clear!
Respect to the author!
But, I'm not very good at electronics. Therefore, the author, please tell me where the INPUT and OUTPUT to the motor are in the scheme??
.
Смотрю из России.
Хорошо и качественно сделано!
Просто и понятно!
Респект автору!
Но, я не очень силён в электронике. Поэтому, автор подскажи пожалуйста, где в схеме ВХОД и ВЫХОД на мотор??
Show😂😂😂😂 the temperature of mosfets😂😂😂😂😂
👍👌 Blagodarim 👍💟💙💗
hola exelente elvideo de montaje
voy a hacer el circuitopara ver si funciona
por que lei muchos que no creen y no esplican
por que ademas pretenden manejar un auto electrico o jumbo jet con un circuito de experimmentacion exito y salud
Is the input dc or ac?
12 - 18V DC
صديق.اين مخطط الدارة.شكرا
How many volts is supplied to this?
Thank you ? Input was 12 v dc ?
8 - 18V
How did you manage to get your power in if it a three phase delta ànd it only three cables coming out as your supply output feed or load, May I know your positive input then ??????
Before you regret it, you better just buy cheap ESC. Great Scott just prove it fake 🙃
Hello, good video, I have a broken hoverboard. Would this circuit work for me to activate the motors in other projects?
It’s cool, thank you very much🤝
E bike cycle gear motor control driver make me please please please
How many volt input?
But it dosent work with brushless motor with only 3 wires.
40 amp and waht volt motor cab be run? Can we run 48v motor with this?
i see its a 4 pins not 3 pins one how can it be used for the 3 pins ones then
For 3-pin control it must be with 6 MosFet's and controlled by a microcontroller.
I converted my BLDC motor from Delta to Star type connection
@@ErCanEverything i see
was having hope for an easy for the 3 pins motors to be under control like the 4 pins ones
hello i dont under stand where u give battery + supply pl tell me i like youe this vedio can this cricut run 48 volt bldc hub motor
where is the diagram ? a good job should have a good clear outline
I am looking for a detailed schematic with more power
Quantos voltes ?
Sir, How many watts that one? Can I use that for 310vdc 120w?
My motor has only 3 wires. no 4 wires like video. then how to do. please help
fake video
I've made it like this but it doesn't want to play, why? the motor is locked, it won't move. used motorcycle photocopy diameter 6cm 12pole stator 10 pole rotor
The motor must have 4 cables, 3 phases and one common cable that connects to the positive.
If you connect in this way then there is a burned out transistor. Try starting with a lower voltage of 8V. Because my transistors burned several times because I was trying to start with 15V. Once it starts, you can increase the voltage to 20V.
But this video is a test only
@@ErCanEverything I've tried it using an adjustable 8v dc voltage MAGICAL transformer, the motor will spin and I raise the voltage again to 15v rpm and it reads 5000 very strong power.
Strangely, I tried using the 12v DC drill battery again, it wouldn't spin and the motor locked, but when I used the transformer at 4000rpm while the supply was rotating, I replaced it with a drill battery, the motor kept spinning and the power was stronger.
How can that be explained?
Thank you!
When the transistor fails then it locks the motor. With disconnected motor measure with a multimeter there must be no short circuit between the pins of the transistor
Hallo. Könnte man die Schaltung so ändern dass man einen 220 Volt bldc Motor betreiben kann?
What is input voltage video not complit
Are hola sensors installed in the engine or is there an additional controller?
Hall sensors are in place but I have not connected them and there is no additional controller. But I connected 1 extra cable to a common point of the three cables, this red cable goes inside the motor and is connected to a common point and that's.
@@ErCanEverything Do I understand correctly that transistors give a phase shift, in fact they perform the function of a hall sensor?
The transistors are lined up with the help of diodes and resistors and thus the motor starts to rotate
@@ErCanEverything Thank you, a useful thing
Thank you🙏🙂
is it 12V in ?
Yes 12V
Is it reliable to driver a 12v 1200kv rldc motor?
Circuit design video full video not a link give me
How many volts does the controller work?
how does this work? is it similar to astable multivibrator?
No
Great 👍👍👍
Thank you my Friend🙂
Can I use a 10k pot?
Yes
nice job bud!
i only have one cuestion, when you turn the pot to the minimun, the power output is off?
Beautiful work , prototype is big business
Hello something doesnt add up here where is the red -positive wire connected to under the motor, as you conveinently hiding it from view ,as normally bdlc motors only have ,yellow/green/blue ,phase wire , So we ask you, Where is the red wire connected , if you dont answer ,we will asume fraud and seek demonizing
I connected the red cable inside a common point of the motor, changed it from delta to star type connection but it can now be used both ways. This controller only works with common point motors.
@@ErCanEverything How a normal bicycle hub motor can have a common point of star connection? Is there any provision that the circuit also work in delta configuration as well?
@@ErCanEverythingdid you made any video how to do it delta to star please answer
Normally bdcl motors, like the one shown in the vid have 8 wires..3 phase and 5 sense.
A2212/13 KV1400
This motor work you making controller
Im looking for the same, but i think that you will not be able to controle it properly due to not having pwm input. And im not sure but i read that it cant go 0 rpm so is useless.
good good^^
CAN IT WORK ON BLDC CEILING FAN ? IF NO MAKE VIDEO ON IT.