U9E2 is a mosfet driver IC and usually burns out the little resistor above when it goes bad, the resistor acts as a fuse and prevents more damage to the board. The part number for that component is NCP5901BMNTBG
@@TheCod3r do you have an online store front, I have this issue with an xbox one s console and want it fixed. I didn't spill anything on it but has similar issue.
I'm not surprised that the fixes didn't work, the board was still caked with what ever was spilled on it. The board once it was first looked over and saw where the damage looked to be, should have been washed over with alcohol to clean it. Then reflow the solder.
@@tomcadero9875 Used to working in console/pc repair for over 15 years before I moved on to Network specialist for a UK telecoms company, but what do I know?
Ever try an ultrasonic cleaner? I have revived/repaired MacBook logic boards with just running it thru there. Works especially well (50% of the time) with any boards without any burn marks. Corrosion is blasted away with osolating ultrasonic waves. 5 min, then rinse with 90% isopropyl alcohol and then dry with air compressor and let sit overnight. Board looks good as new and also eliminates all corrosion issues.
This is the time when we make the device work more soon afterwards we receive a bucket of cold water when we realize that there was no image. More and still these are bones of the trade. congratulations you are a great professional ...
I agree. Special when you said the first monitor showed out of range. I do not have the quick 2 buttons to press to reset it. Hopefully you can see these messages before taking the whole thing apart again.
I have this exact job on the bench currently, interested to see what your fault is and if it's the same on this one.. I also had a blown R9D30 resistor, and a faulty transistor next to it on top of the 2 chips here, took me ages to find it!
Ya did the do. It's all anyone can (and should) do. You can't overlook the care & feeding of your office's #1 asset. Without it... you are both lost. Eat/Sleep/Repeat. And thank God you enjoy your chosen profession. So few people have that luxury. You make a measurable difference every day ❤
Ya like the guy below said hold eject and press power and hold them both for about 6 seconds resets resolution to 680 i have to do that sometimes after a port and retimer replacement no clue why but is what it is!!! Worth a shot!
Have a similar issue on my bench right now. They took it to UBREAKIFIX and they ran it through an ultrasonic without inspecting, so finding the issue is proving troublesome. The standard mosfet failure is not my issue - all test ok. A bit of a head scratcher that I admittedly have set aside for other work. Will have to re-visit.
I love your channel, but during this video, the youtube injected TWO commercials by 2/3 of the video!!! If the add is at the end or even at the beginning, that is OK. THANKS AGAIN!!!
I have the same power problem with my xbox one x. Barely used it. No water exposure. It was in a Gaems case between my legs while I was opening a door and it fell like 2 or 3 inches and now it powers on for barely enough time to eject the disk that was in it. Wondering if a chip had weak solder or something after watching this. I'm not really equipped to do what you did. it's a shame because I barely used that xbox for almost a year and I finally start using it again and this happens. One day I might try to find a repair shop like yours
Would’ve been interesting to see the board under a thermal camera. Side note try a different HDD, a bad one may cause a no signal although I doubt this is the case here.
Had a one s doing that to me after changing the hdmi retiming chip. Pressed the sync and power then released the power. Was doing this because the resolution output for my monitor was wrong.
I dont understand how people spill drinks onto their gaming consoles. Mine sits next to my TV and I dont put drinks there😂🤣. I have a couch with a table for those reasons🤦♂️
I think the last issue of the xbox after you fixed it is that you need to reset the display settings of the xbox. Start it in safe mode. It should fix the issue. The xbox clearly is fixed now :)
@@dietbountyicecream1444 alcohol as in isopropyl alcohol is fine I've been cleaning electronics for 20 years that way please learn before spouting nonsense
How is it when you receive a very dirty board, you do not clean it of debris, after noting areas of concern??? Very often those bits of debris are moist, and that can cause problems on a continuing basis. There are various liquids in pressurised cans that are electronic cleaners.
The Xbox cannot display the signal as the resolution is too high for your display. You can reset it by holding a few buttons as far as I can tell. I think it's the power and eject button for 10 secs
Hi im a huge fan of your doings im from philippines. I want to ask what flux you usually use and flux cleaner i want to practice to solder im an IT student and i want to learn more i cant buy on your merch coz i dont have cards to pay . Thankyouu in advance 🥰
Having the same problem, mosfets check out ok, can not see any other issue except for the usb port in front, looks like someone tried to repair with a new one, i dont see solder all the way threw the hols in the pcb...... could that throw a short and shut down issue?
My xbox one s power supply went bad from lightning a while back so I ordered a new one. When I went to turn it on it cut on and right off. I noticed I broke the power button off of the pcb board so I ordered a new one. Just installed the new one and it still won't stay on. I have no idea what to try now
Out of range HDMI means the display can't handle the incoming signal settings. XBOX One can do 4K and if it is set for that resolution then any display connected to the console that can't handle the incoming signal resolution will give off that message. I'd just like to know what chips you replaced so I can fix mine.
1:35 you touch one side of the capasitor. i saw this in few videos expected you tell where is the other prop. :) i hear the beep but where do you touch the other prop?
is he going to just start pulling parts off like he did with that switch lite he was trying to fix he has all this fancy repair stuff and before he even used any of it to check for problem spots he just started pulling stuff off the board with out knowing if they were even broken 1 min in he is like oh this needs to go
It’s educated guessing and a gamble based on experience with many repairs of similar issues. I believe he has troubleshooting skills but he is running a business and trying to maximize throughput. There are probably other channels on RUclips that do in depth troubleshooting and analysis. But they probably aren’t trying to run a profitable business with a large backlog either.
Mine was struck by lightning I took it apart and I see no damage anywhere it powers on the light comes on then cuts back off spent hours just cutting it on to just cut back off I swapped the battery back because mine wouldn't power on at all to my friends his was struck to but his power box lights mine up to just cut back off idk what else to do
Hello, I was wondering if it is always going to be an issue with the motherboard when an Xbox does that; turning off immediately? or could it also be the power supply? My Series S does that.
How did you do that, it's amazing? I have an Xbox one x coming in the mail and need a person of your expertise to do that but where to look is a mystery.
I have an Xbox 360 problem, I can turn it on with the controller the power supply is green, and the console does turn on, but after about 5 min everything turn off. How can I fix this?
do you have a video repairing xbox one x? My does not turn off and I know its not a liquid issue. I was going to replace power supply but now I have seen the south bridge issue of them going bad. Help Thanks
Once the chip is off the board what do you use to keep the new chip stuck to the board I got a hot air station in flux low melt wire but it keep sliding all over the place 😢😭😭
I am testing the same thing on a regular xbox one motherboard, all the mosfets are apparently okay, but when I test voltage the mosfets are only receiving/outputting 0.2V! Any clues what the problem might be?
![[#2024MAMA] G-DRAGON - 무제(Untitled, 2014)+POWER+HOME SWEET HOME+뱅뱅뱅+FANTASTIC BABY | Mnet 241123 방송](http://i.ytimg.com/vi/Ox29z5Nf1Uk/mqdefault.jpg)
You’ve become my favorite teacher for electronics repair. Straight to the point, always honest, no bullshit.
U9E2 is a mosfet driver IC and usually burns out the little resistor above when it goes bad, the resistor acts as a fuse and prevents more damage to the board. The part number for that component is NCP5901BMNTBG
Also 51916 is a ddr3 memory power management ic (TPS51916) and regularly goes bad
@@graphicscardtech3167 yeah they're a little tricky to find but they are available 😃
@@graphicscardtech3167 yeah I also buy them in bulk because it's cheaper and I fix hundreds on xbox one s consoles with the same problem lol
@@TheCod3r do you have an online store front, I have this issue with an xbox one s console and want it fixed. I didn't spill anything on it but has similar issue.
The man, the myth, the cod3r lol. Freakin legend man.
Thank you brother. Cause of you I just fixed my son's Xbox one s that thought was doomed. Wish I could buy you a 🍺. Thank man.
It’s always the best you bring out both your work n knowledge
Its like he does it as a job or something
He makes it look easy.
It is easy
You are a true repair savvy. Thank you for more inspiring and encouraging lessons. The best wishes from México
I'm not surprised that the fixes didn't work, the board was still caked with what ever was spilled on it. The board once it was first looked over and saw where the damage looked to be, should have been washed over with alcohol to clean it. Then reflow the solder.
he needs a ultrasonic cleaner
Correct, he did not clean all that mess how it will work with some liquid working probably as a conductor .
exactly, I was wondering too, why is he not cleaning all the liquid
Lol..look at all of these "experts".
@@tomcadero9875 Used to working in console/pc repair for over 15 years before I moved on to Network specialist for a UK telecoms company, but what do I know?
I hate leaving a job in full flow to come back to it. 👍🇬🇧
1:58 thanks for the info.
Ever try an ultrasonic cleaner? I have revived/repaired MacBook logic boards with just running it thru there. Works especially well (50% of the time) with any boards without any burn marks. Corrosion is blasted away with osolating ultrasonic waves. 5 min, then rinse with 90% isopropyl alcohol and then dry with air compressor and let sit overnight. Board looks good as new and also eliminates all corrosion issues.
Long time man good video I've been watching alot of these lately
You will find out because you are the master in this
This is the time when we make the device work more soon afterwards we receive a bucket of cold water when we realize that there was no image. More and still these are bones of the trade. congratulations you are a great professional ...
Totally amazing
I just love the way you do videos
Very informative and amazing skills!
Keep them coming
I bet it’s the video settings. It could be set to 4K.
I agree. Special when you said the first monitor showed out of range. I do not have the quick 2 buttons to press to reset it. Hopefully you can see these messages before taking the whole thing apart again.
On old board letters on chip were AZE, and 1 was down left, while on donor board letters on chip were AZH and 1 was upper left
I have this exact job on the bench currently, interested to see what your fault is and if it's the same on this one.. I also had a blown R9D30 resistor, and a faulty transistor next to it on top of the 2 chips here, took me ages to find it!
Why didn’t you just test the chips before replacing them?
Ya did the do. It's all anyone can (and should) do. You can't overlook the care & feeding of your office's #1 asset. Without it... you are both lost. Eat/Sleep/Repeat. And thank God you enjoy your chosen profession. So few people have that luxury. You make a measurable difference every day ❤
That's why I drink 70 proof vodka now. A spill won't destroy electronics.
this man is a genius
Do what I do. I make my own alcohol with no methanol lol. It’s methanol that gives you hangovers and also absorbs water lol.
This is some super cool stuff I wanna learn about the tools u used during this video
Solder, iron, quik brand hot air station, amtech Flux.
Microscope
did you try the button combination to reset the display settings (might have been set to 120 hz and or 4k)
Best of luck and I hope you get it working today!
And this kids is why you don't keep liquids near your electronics
Exactly what I need to be watching at 4am.
You have to reset the display resolution in order to work on lower spec tv
How to do it?
Ya like the guy below said hold eject and press power and hold them both for about 6 seconds resets resolution to 680 i have to do that sometimes after a port and retimer replacement no clue why but is what it is!!! Worth a shot!
Sir can u make an online coaching class for this topic exclusive. love from India
Check their website, they do trainings
Have a similar issue on my bench right now. They took it to UBREAKIFIX and they ran it through an ultrasonic without inspecting, so finding the issue is proving troublesome.
The standard mosfet failure is not my issue - all test ok. A bit of a head scratcher that I admittedly have set aside for other work. Will have to re-visit.
Every video im amazed amazing job!
Really nice work. Well done.
I love your channel, but during this video, the youtube injected TWO commercials by 2/3 of the video!!! If the add is at the end or even at the beginning, that is OK. THANKS AGAIN!!!
I have the same power problem with my xbox one x. Barely used it. No water exposure. It was in a Gaems case between my legs while I was opening a door and it fell like 2 or 3 inches and now it powers on for barely enough time to eject the disk that was in it. Wondering if a chip had weak solder or something after watching this. I'm not really equipped to do what you did. it's a shame because I barely used that xbox for almost a year and I finally start using it again and this happens. One day I might try to find a repair shop like yours
Would’ve been interesting to see the board under a thermal camera. Side note try a different HDD, a bad one may cause a no signal although I doubt this is the case here.
Saved me $40-$100 on new controller... Working like new 0 drift on cod with deadzone at like .05 was between .2 and .3 on deadzone 💪🏾💪🏾💪🏾
Tip: Press Sync + power on button... to override scale options... don't blame old man ;)
Idk if I trust that
Had a one s doing that to me after changing the hdmi retiming chip. Pressed the sync and power then released the power. Was doing this because the resolution output for my monitor was wrong.
did you ever find a fix? im having the same problem
Id love to work and learn from you.
Nice video as always. Would an ultrasonic cleaner be advisable due to the liquid spill?
lol, thumbnail made it look like a happy ending.
plot twist
Thanks so much. I have the same 1 at my shop.. i bought to part out
Great video👍.did you find fault? Gues hdmi controler dead.let me know if you fix it.cheers
I dont understand how people spill drinks onto their gaming consoles. Mine sits next to my TV and I dont put drinks there😂🤣. I have a couch with a table for those reasons🤦♂️
are you accepting new clients? i’m having the same problem, very sad.
I think the last issue of the xbox after you fixed it is that you need to reset the display settings of the xbox. Start it in safe mode. It should fix the issue. The xbox clearly is fixed now :)
Halo sar.u r a.genius .difrent style ok repair.god bless u.u r smile is good
Good job.
It should cleaned before start soldering right ?
to check if retimer issue hold the eject button when you power on until it beeps a second time. if boots into 480 low resolution mode its the ic bad
If possible please share your method of diagnosis.
Where do you get the capacitors and other components on the motherboard?
You should've clean the whole board with alcohol first
Noooo
@@dietbountyicecream1444 alcohol as in isopropyl alcohol is fine I've been cleaning electronics for 20 years that way please learn before spouting nonsense
Every xbox ive ever had has inexplicably died. They are complete trash.
Yeah it sounds WAY TOO GOOD to be true.
How is it when you receive a very dirty board, you do not clean it of debris, after noting areas of concern??? Very often those bits of debris are moist, and that can cause problems on a continuing basis. There are various liquids in pressurised cans that are electronic cleaners.
The board still had flux residue and spillages still on it when retested.
4:54 image quality is great, but 11:42 is greater, guess not that great.
The Xbox cannot display the signal as the resolution is too high for your display. You can reset it by holding a few buttons as far as I can tell. I think it's the power and eject button for 10 secs
Hi im a huge fan of your doings im from philippines. I want to ask what flux you usually use and flux cleaner i want to practice to solder im an IT student and i want to learn more i cant buy on your merch coz i dont have cards to pay . Thankyouu in advance 🥰
This is quality repair,i really enjoyed this video
Nice job thank you Sir
When are doing the second part/completion for this console???
yea right that thing is toast now
I love u r work style Super
Which solder paste and soldering iron u r using kindly reply sir
No follow up video ?
How are you able to tell there’s no short if you only test one side of the capacitor?
Where do you get the metal tips for you solder paste and what size are they I can't find a good size anywhere most are too small
Having the same problem, mosfets check out ok, can not see any other issue except for the usb port in front, looks like someone tried to repair with a new one, i dont see solder all the way threw the hols in the pcb...... could that throw a short and shut down issue?
My xbox one s power supply went bad from lightning a while back so I ordered a new one. When I went to turn it on it cut on and right off. I noticed I broke the power button off of the pcb board so I ordered a new one. Just installed the new one and it still won't stay on. I have no idea what to try now
Out of range HDMI means the display can't handle the incoming signal settings. XBOX One can do 4K and if it is set for that resolution then any display connected to the console that can't handle the incoming signal resolution will give off that message. I'd just like to know what chips you replaced so I can fix mine.
1:35 you touch one side of the capasitor. i saw this in few videos expected you tell where is the other prop. :) i hear the beep but where do you touch the other prop?
is he going to just start pulling parts off like he did with that switch lite he was trying to fix he has all this fancy repair stuff and before he even used any of it to check for problem spots he just started pulling stuff off the board with out knowing if they were even broken 1 min in he is like oh this needs to go
Oh there is no real troubleshooting going on here at all, it's just visual inspection and then replacing whatever components.
It’s educated guessing and a gamble based on experience with many repairs of similar issues. I believe he has troubleshooting skills but he is running a business and trying to maximize throughput. There are probably other channels on RUclips that do in depth troubleshooting and analysis. But they probably aren’t trying to run a profitable business with a large backlog either.
Does your solder station make a difference I could not get mine to melt the solder
ONE THING FOR SURE IS TO NOT DROP LIQUID ON AN ELECTRONIC DEVICE........NICE ONE ...KEEP IT UP.....
What temperature do you set your hot air gun to desoder the chips?
4:48 How do you get rid of the glare, looks so much better. I have issues with that and my microscope!
turn on/off the light source of the microscope, you can find it on his website shop
what is that gel 4:24?
Mine was struck by lightning I took it apart and I see no damage anywhere it powers on the light comes on then cuts back off spent hours just cutting it on to just cut back off I swapped the battery back because mine wouldn't power on at all to my friends his was struck to but his power box lights mine up to just cut back off idk what else to do
hi what flux u use ...brand for re balling?
How do you get rid of the glare?
Hello, I was wondering if it is always going to be an issue with the motherboard when an Xbox does that; turning off immediately? or could it also be the power supply?
My Series S does that.
use toothbrush with alcohol to clean water damage boards it is best way to cleaning up
How much did you charge the customer for this job? I had a power surge from a lighting storm
I’m having the same problem with my Xbox, but it have signal. It’ll just shut off randomly after a few seconds or even a few minutes
Mine began doing this after I got it repaired, though it would turn on eventually.
Nice job and video
what is your soldering temperature?
How did you do that, it's amazing? I have an Xbox one x coming in the mail and need a person of your expertise to do that but where to look is a mystery.
I have an Xbox 360 problem, I can turn it on with the controller the power supply is green, and the console does turn on, but after about 5 min everything turn off. How can I fix this?
Hello!
Brother, can you tell me your shop location?
Can you do a part two
whats the difference bewteen the 2 flux u use?
Mine is doing the same thing. I didn’t spill anything on it. Now what?
Awesome ✌️✌️✌️
Hi good teacher?, l wanna ask
You what can l do for my laptop which crushing operating system after to install it, they happened after 1 or 2 mouths.
do you have a video repairing xbox one x? My does not turn off and I know its not a liquid issue. I was going to replace power supply but now I have seen the south bridge issue of them going bad. Help Thanks
How much do you charge to send a mother board to to get it fixed
Probably something just didn't get plugged back in correctly when U put it back together. Happens to me sometimes. lol
Same when I fixed my original Xbox the IDE cable wasn't plugged in properly so I just got error 6
Once the chip is off the board what do you use to keep the new chip stuck to the board I got a hot air station in flux low melt wire but it keep sliding all over the place 😢😭😭
I am testing the same thing on a regular xbox one motherboard, all the mosfets are apparently okay, but when I test voltage the mosfets are only receiving/outputting 0.2V!
Any clues what the problem might be?