I know it's a long time since you did this video, but I very much appreciate it and since I always like to recycle and love older Nissan, this one is perfect for my inevitable gearbox failure of my 90 Pulsar GA16DE N14, maybe this gearbox isn't exactly the same, but it's everything I needed, especially when I wasn't planning on rebuilding it to begin with and wasn't careful with the initial autopsy, its had so much damage and couldn't even hold oil, but I fix casing damage, but I didn't know which detent spring position was correct, but you showed me very good photography that I was able to clearly see the thin spring goes in the upper hole and the strong one is with the ball, excellent job once again, I also love your motorcycle engine rebuild, thank you awesomely again and kind regards Simon at Rotoma New Zealand 🇳🇿
Exactly what I was thinking 🤔 😂, perfect for my current situation after major Pulsar gearbox failure and wreckers can't be bothered keeping anything so old where I am.
Hi guys. I need some advice. I replaced my clutch master cylinder kit a month ago. New clutch & pressure plate in April this year. Today I took off up a hill 1st gear, got onto flat road, can't get 2nd gear. Switched t van off. Tried adjusting pin by clutch pedal, bleeded t master & slave cylinder. Van goes into gear, but won't slow down when clutch is pressed down. I put a new master & slave cylinder. Bleeded! Van is only selecting 1 - 3 - 5 Not selecting 2 - 4 - R What could be the reason for not selecting 2 - 4 - R?
Хобби
Tbh this is such a well thought out video! Teardown, cleanup, order of installation AND part numbers?!?! AWESOME!! 🙌🏽🙌🏽
Es por esto que pago el internet, increible super explicado y sin decir una palabra, gracias amigo
I know it's a long time since you did this video, but I very much appreciate it and since I always like to recycle and love older Nissan, this one is perfect for my inevitable gearbox failure of my 90 Pulsar GA16DE N14, maybe this gearbox isn't exactly the same, but it's everything I needed, especially when I wasn't planning on rebuilding it to begin with and wasn't careful with the initial autopsy, its had so much damage and couldn't even hold oil, but I fix casing damage, but I didn't know which detent spring position was correct, but you showed me very good photography that I was able to clearly see the thin spring goes in the upper hole and the strong one is with the ball, excellent job once again, I also love your motorcycle engine rebuild, thank you awesomely again and kind regards
Simon at Rotoma New Zealand 🇳🇿
Excelente video lo felicito y sin música lo capto mejor gracias
thank you so much sir . looking forward to see toyota engine & gearbox sir . love and respect to😍you
Una obra de arte estimado , felicitaciones .
Exelente video hermano
Excelent!!
Great job Machan!
Exelente trabajo
Good job guys
Beautiful!
Exelente aporté amigo una pregunta y esa caja es igual al del Nissan E16 o cambia bastante el en sanblaje de antemano gracias bendiciones
Great job mate!!
Thank you
How did I miss this? Thank you!
Exactly what I was thinking 🤔 😂, perfect for my current situation after major Pulsar gearbox failure and wreckers can't be bothered keeping anything so old where I am.
good work
Osm video sir👌
Deslanto good work man
Thank you
Super ❤
Oohhhh nissan sunny is love me
What gearbox oil should i use
Why did you not tear down the shafts to inspect the synchroniser rings, as well as the bearings/bushings under the gears?
They never fail and last forever on these Nissan transmissions.
Hi guys. I need some advice.
I replaced my clutch master cylinder kit a month ago. New clutch & pressure plate in April this year.
Today I took off up a hill 1st gear, got onto flat road, can't get 2nd gear.
Switched t van off. Tried adjusting pin by clutch pedal, bleeded t master & slave cylinder.
Van goes into gear, but won't slow down when clutch is pressed down.
I put a new master & slave cylinder. Bleeded!
Van is only selecting
1 - 3 - 5
Not selecting
2 - 4 - R
What could be the reason for not selecting 2 - 4 - R?
There might be problem with shifter and the selector in the gearbox,not the clutch.because the gear shifts front, not back.
Where can I buy this parts
❤❤❤❤❤❤❤❤❤❤❤❤
What is this on 1:29
Where are you location?
😯😯😯😯😯😯😯😲😲
Can you restore 4dr5 or 4dr6 engine and gearbox ......
Не стоит ремонтировать у этого "мастера". Он тебя обманывает.
@@wwz1100 I can understand English or Tamil ...
@@mohamedshafeelmohamedbilal6364 русский тоже выучи
Ok now I can understand you.....u r mantal .... I am loser🤣🤣🤣
昔良くやったなぁ。
それと、プレス機真似します。(´･ω･｀)
Kitna kharach aa gaya