Thank you for this video. I tried following the written instructions on your site, but was doing it wrong. Kept putting in the number of remotes I wanted to pair as the test value, hitting save, then pressing the unlock button. Video helped me match my remotes properly :)
No, vehicles with the 4D Chassis Code use a different method that doesn't require a dealer level scan tool. Registered users of VCDS can email us for the instructions. You can find our contact info when you click the [About] button.
I purchased a replacement remote control with the same frecuency as original one, I made that same procedure to program a second remote control but did not. Just the original one is recognized. What type of remote control need to be purchased ?
Hello, Thank you for the video but in Audi A4 B8 2008 they key must be inside the ignition! so now ay to press the Lock bouton! plz for your advice. Thank you!
After reading the Ross-tech immo versions 1-4 info page, am I correct in thinking you can't program new virgin remotes like this as it's either a version 3 or 4 immo and you need the pin/skg? I only have one remote fob and require a second. Thanks in advance.
My 8E doesn't display a stored value when I enter channel 21 and click read, and the New value box remains disabled. Also, entering 00 then read does not present the message you show. Any clues?
I'm having a problem...I can't connect to Module 46-Central Conv, on 01-Engine for example works fine but 46 or 25 i can't acces it. I need help, thanks !
All our registered users can contact our Tech Support Department via email. You will find our email address when you click the [About] button from the first screen of VCDS.
+Oleg Voronič If no errors ocurr in 46Centr.Conv. Try to match friends/similar remote, if it succeed, your remote is dead. Buy a new one. We had a situation in one A4B7 with 2 remotes dead :/
@@djshaker hello, same issue here, original key fob doesn't match but a new one matches but it works for about 10 minutes. After that it stops working, if I match it again it works again for only 10 minutes... any ideea why it doesn't stay matched?
@@irinelstancescu4073 Also check if your car battery is OK. It sounds like it could not save the settings. This usualy happens when the car battery is disconnected or bad.
hi, i can connect to central conv, than adaptation, clear on chanel 00, move to 21 channel. I am giving the new value (1 or 2), click test. Finally when I press the lock button on the remote, adjustment is not changing to recognized... WHY??? :(((
+Matei Cristi If no errors ocurr in 46Centr.Conv. Try to match friends/similar remote, if it succeed, your remote is dead. Buy a new one. We had a situation in one A4B7 with 2 remotes dead :/
Thank you for this video. I tried following the written instructions on your site, but was doing it wrong. Kept putting in the number of remotes I wanted to pair as the test value, hitting save, then pressing the unlock button. Video helped me match my remotes properly :)
Tried other methods, didn't work. This method is perfect. THANK YOU!!!!!
No, vehicles with the 4D Chassis Code use a different method that doesn't require a dealer level scan tool. Registered users of VCDS can email us for the instructions. You can find our contact info when you click the [About] button.
Thanks alot for this amazing tutorial video. Helped me whit matching keys for my audi a4 b6.
I purchased a replacement remote control with the same frecuency as original one, I made that same procedure to program a second remote control but did not. Just the original one is recognized. What type of remote control need to be purchased ?
Hello, Thank you for the video but in Audi A4 B8 2008 they key must be inside the ignition! so now ay to press the Lock bouton! plz for your advice. Thank you!
Hello, the procedure is also valid for Audi A3 Sportback year 2004 with key code: HL0 8P0 837 231?
Hello what fréquence b6 8h need ? I have 443.9Mhz remote but don’t work
After reading the Ross-tech immo versions 1-4 info page, am I correct in thinking you can't program new virgin remotes like this as it's either a version 3 or 4 immo and you need the pin/skg? I only have one remote fob and require a second. Thanks in advance.
Did you also buy a new flip key remote and it won't link/program?
Hi, prefect. locks and unlocks but the middle button to open the rear gate does not work - did I miss something?
Rear lid buttons typically need to be pressed and held for a few seconds, not single click like the lock/unlock buttons.
My 8E doesn't display a stored value when I enter channel 21 and click read, and the New value box remains disabled. Also, entering 00 then read does not present the message you show. Any clues?
What I should do if I got a statement about not respond from the controller?
how much is the ross tech vcds
I'm having a problem...I can't connect to Module 46-Central Conv, on 01-Engine for example works fine but 46 or 25 i can't acces it. I need help, thanks !
All our registered users can contact our Tech Support Department via email. You will find our email address when you click the [About] button from the first screen of VCDS.
Yeah.. My A3 8L also cannot connect to 46. It just says "No response from controller"
Would this work for a 2001 S8?
Hello,
Same problem to me.. Audi A4 B7 2006, in module 46 channel 21 adjustment is not changing to recognized with both keys.. Any ideas RossTech?
+Oleg Voronič If no errors ocurr in 46Centr.Conv. Try to match friends/similar remote, if it succeed, your remote is dead. Buy a new one.
We had a situation in one A4B7 with 2 remotes dead :/
@@djshaker hello, same issue here, original key fob doesn't match but a new one matches but it works for about 10 minutes. After that it stops working, if I match it again it works again for only 10 minutes... any ideea why it doesn't stay matched?
@@irinelstancescu4073 Comfort module under the drivers seat is wet and doesnt work as it should. Dry it.
@@djshaker thanks a lot! I'll have a look.
@@irinelstancescu4073 Also check if your car battery is OK. It sounds like it could not save the settings.
This usualy happens when the car battery is disconnected or bad.
We have different types of interfaces. Please go to our website and contact our sales department. URL listed at the end of the video.
Thank you.
i have one key fob,how to add it?after battery changing in car,fob not working.
hi there. i have the same problem. only one key fob. how did you sort out this problem. thanks.
Press unlock button. Turn the ignition on and off, pull the key out and press the unlock button again.
dont work buddy :)
What about 8D?
thank you!
Thanks
hi,
i can connect to central conv, than adaptation, clear on chanel 00, move to 21 channel. I am giving the new value (1 or 2), click test. Finally when I press the lock button on the remote, adjustment is not changing to recognized... WHY??? :(((
+Matei Cristi If no errors ocurr in 46Centr.Conv. Try to match friends/similar remote, if it succeed, your remote is dead. Buy a new one.
We had a situation in one A4B7 with 2 remotes dead :/