2016 Ford Fusion Oil Change
HTML-код
- Опубликовано: 26 авг 2024
- This is the first time I have changed the oil in the Fusion since I bought it. In the nine months I've owned it I might have driven it 4,000 miles. It sits there in the driveway mostly. I may order a new engine cover for the bottom. It was put there for a reason.
The bottom cover, which was cut out on this car, doesn't have an access hole for the filter or drain plug (at least not on my 2016, 2.5L). It has 11 screws with 10mm heads. Most of the screws go into plastic inserts, so be careful not to strip them out.
This cover helps with aerodynamics - gas mileage, and in the rust belt, should keep some of the salt off of things.
Also, when using ramps, you will likely need to put boards or something down in front of the ramps to keep the front spoiler from hitting the ramps.
Hope it helps!
I bought one of those yellow funnels and before I could use it my wife borrowed it and from then on it's been a kitchen funnel.
Finally someone who actually shows you how to do it .
He did not put oil in the filter. Air is therefore pushed into the engine oil passages and bearings.
Always put oil in the filter before installing. And if there is room, like this one was down a half quart, put some Marvel oil or just motor oil and drive the car mildly for about 10 minutes. This is also a good time to put some top cylinder lube in the fuel. Use a quality filter... no cheapies.
Try to find or buy the right size filter wrench, I had two in my tool box, ended up buying two more.
Thanks brother! Now to get this done.
Torque wrench recommended for tightening the oil plug if you can figure out the foot pounds for the plug.
Matthew Ludivico Torque wrenches are for people who don’t know when to stop tightening.
Don't really need one. If you are experienced you can usually feel 20-30 ft lbs (on my car its 26)
Look it up !
Nice job on hacking out the engine cover lol 😆 👌 👏
That wasn't my work. Someone before me did that. Had I kept the car I would have ordered a new cover.
Anyone know the type of screw to hold the splash shield ? I lost some so I need to find a few
Helpful stuff, thanks buddy!
No problem! Glad to help out!
I swear oil change places put a bunch of unnecessary force on the oil drain plug to force you to take it in.
Where in the world do you jack these things up at ? I can hardly look under mine and i have shields everywhere.
Right lol
Took me forever to change a tire
How come you said that you dont waste your time changing the oil on a cold engine?
The idea is that the very warm or hot oil will drain out of the engine quicker than cold oil. The hot oil is slightly thinner. I wouldn't call it a waste of time. On a hot or cold engine I walk away for a half hour or so and let it keep draining/dripping out.
@@Deucealive75 its because any contaminants settle to the bottom of the pan when its sits a while. So the idea is that running the engine until its warm will suspend the contaminants into the oil so that they are removed when you drain it. Otherwise if you drain it on a cold engine any contaminants that settled to the bottom may not drain out. Thus contaminating the brand new oil you replace it with.
Thank you. 😺
Did you 2016 Ford Fusion Se came with an engine cover????TIA
u kinda missed the part to unscrew the plastic cover, but good video overall👌
ENGINE OIL CAPACITY ?
ag qara X 6.3 litres according to ford
The 2.5L holds 5.7 quarts of oil
Who cuts the bottom cover ? Honestly
thanks
Ever done a transmission fluid drain and refill?
Yes, you need to search it on RUclips.
Washer coolant
Hello everyone any hints where . Is the fuel filter on Ford fusion And how can I to change it any special tools. thanks
Sealed inside, non serviceable
@@jfcypranowskikhs That's insane!!
In the fuel tank.
@@ramdbzdude0_0 that's pretty common now, the filter is like a cloth mesh which is at the pumps intake.
Why don’t you use Motorcraft oil?
I have used Castrol oil for years. I have used it ever since I've had a driver's license. Nothing against Motorcraft; it's most likely Havoline or something like that. What sold me on Castrol was years ago I tore down a 351 Windsor that had nothing but Castrol run in it since the day it was put together. Had 120,000 miles on it and the inside was just as clean as the day it was built.
@@FerdinandMagellan08 Cool. I used to run Mobile One in everything until I bought a new 2016 F165 (F150 with the 2.7 ecoboost aka 165 cuin v6).
@@blackericdenice what do you put now in your vehicle?
@@alextran8188 Motorcraft 5w30 snthetic blend. If Ford say to use it in a twin turbo v6. It should be fine in my 2004 Trailblazer and my 2001 Deville with the Northstar.
I put ford recommend 5w20 in my 1.5 eco fusion, but it is Amsoil and a full synthetic. It doesn't hurt to go with a higher grade oil such as a Full Synthetic, and a brand such as Amsoil or Pennzoil
I bought my wife one of those ford fusions, i tested toyota and honda and the fusion is a nicer and better car. Castrol Syn best oil out there.
This car is a piece of shit, my transmission already failed on it cost me $7000 for a new one
Why did you cut the engine cover? That is $100 piece of plastic. Just wondering?
I didn't cut it. Some other nitwit before me had hacked it. I was thinking about ordering a replacement.
@@FerdinandMagellan08 Then, my friend, you aren't a "nitwit". :-) Someone else sure is though. I have seen those on eBay, Genuine Ford Part for under $75 with free ship. A bit higher from Ford dealer. Take care and, were it mine, I'd replace. Insulation and protection for under carriage.
Traducir en español
Dude I believe trash cans exist the planet isn't your trash can, let try to keep our planet clean.
(oil bottle seal).
Oh, come on!
It’s always good to wait for the “Oil Change Required” message to come on before you should change the oil. Oy vey
You can check the condition of the oil on the dip stick. That's what it is for besides oil level.
Whoever needs to watch this to do an oil change should not be anywhere near a car
RahimKnicks how else do you learn how to change oil then dick head
it helps to see someone else do it on a specific vehicle so u see what size sockets to use and if there r any unexpected scenarios with engine covers and such
2013 Fusion with same engine takes a T27 torx to remove plastic cover, this used 10mm hex head. It's all about information on newer vehicles as they change, sometimes in mid year!
Dumbass fucktard
There's many ways to learn, youtube videos has become a new method of learning, unless you meant that people should just naturally know how to change oil from birth