11:00 Got her done with the help of some JB weld plastic Bond. A few places broke because screws were rusted into the plastic. Thank you for the video. I am a 70-year-old woman and after watching this video I am fixing the back hatch latch all by myself thank you so much
August 2024. Used this video as a step-by-step on my broken 2006 Sequoia door handle. Latch broke in the exact same spot. Great hack with the plastic wrap. Bought everything you recommended and fixed it for less than $50! Thank you Thank you Thank you! 🎉
I have watched many diy videos to learn how to fix my vehicles. Your video is by far the best one I've seen. I'm a 56 yr old woman, and not afraid to save some money by fixing things myself. I have gotten very frustrated with videos where they expect you to know technical terms or where a part goes and they don't show the one critical step you need to do, like they think I'm a mechanic! (If i were a mechanic i wouldn't be watching the videos.) But this video was so clear, easy to follow along, and showed every step. I just ordered the parts from your links and i know because of you I'll have my back door opening again as soon as they get here. Thanks so much for taking the time to make this video!
Thank you so much for the kind words Gail. I appreciate the feedback on the video. I’m so proud of you for doing this yourself. Hopefully everything goes smoothly I’m sure you’ll do great!
Paul, I replaced the broken latch handle on my '02 Sequoia using this video as a guide, as well as ordering my new latch handle and the green things from the links you provided. As several others mentioned, your little trick of using a piece of the plastic wrapper to hold the nut in the socket worked perfectly. What a fine tutorial! Thanks for posting it. For any who are going to be doing this to your Sequoia, let me add a few tips: The lift gate pull attachment referred to at about :50 in the video is normally covered by a plastic trim piece. This is removed by a forceful upward lift on the trim piece. Take note of the orientation of the lock pictured at 4:28 and 9:23 before removing that nut. The lock tab should be installed between the plastic piece on the outside that you're removing, and the sheet metal of the lift gate. I believe on Paul's Sequoia, this had been pulled apart previously and reassembled incorrectly. Once apart, you may note that there is a cut out in the plastic piece designed to hold the lock in place and relieve any gap between it and the plastic piece. If you screw up like I did, JB Weld works very well to repair the damage done to the plastic piece. Finally, as mentioned, the green things are too big. I found that they were very easy to cut down with a razor knife, and work well if you do so. Cheers!
Hey Lyle thank you so much for sharing your tips and tricks with others! My Sequoia may very well may have been worked on in the past And put back in correctly i’m glad you shared your experience with the rest of us. Thank you for the support and I’m glad you got it fixed. 👊
You made fixing my 2005 Toyota Sequoia rear liftgate handle absolutely EASY! Your instructions were so good that even I could do it! Thanks for the great video!
Annnd...this is why, even though I've been a mechanic in various field since 1972, that I always watch ALL of a DIYer's videos even though they might not be at all pertinent to my life. There is almost always some tidbit of a mechanic's trick to learn from everyone. That trick about covering the nut with the plastic sheeting to keep it tight in the socket was a real beaut. I'm 65 now and you can never tell when some helpful hint can come in handy. Thanks for putting this up!
Hey thanks so much for the comment I really appreciate it!! I like watching videos as well and learning tricks of how people do stuff. There’s always something to learn. 😊
Fixed the latch handle on my 07 Sequoia following these instructions. Pretty easy. Took about an hour total considering I didn't know what I was doing and didn't want to break anything. Only spent about $45 getting the part, recommended tools and replacement fasteners. Saved myself hundreds of dollars probably doing it myself. Thanks man!!
This video was extremely helpful and well put together. I have an '04 Sequoia and this is the second latch to break. First was replaced by the dealer so I had no idea where to start. This video definitely helped. I will state that we had an issue taking off the license plate part. found out that the license plate needed to be removed before the part would finally come loose. After that we were done within about 30 minutes. Thanks!
Awesome I’m glad you got it! Yes I forgot to mention in the video since I had mine off already. I pinned it to top comment hoping more would see it too. Glad you got it! Thanks
After watching this video I couldn't wait to fix my handle which I did within 20 minutes. By far the best video with easy step by step instructions. Cheers.
My latch has been broken for almost 8 years. I put it off this long and last week broke my taillight so i had to fix it. Very good video was a much easier fix that i thought! Thank you
Yes, thanks for the comment. I hadn’t thought to mention it when I made the video because I already had it removed ahead of time but I pinned it in the top comment hoping others would see it first. Since I can’t add it to the video later. Thanks
I watch a ton of DIY videos especially now when money is super tight but I’ve never taken the time to comment but felt this one deserved it. $16 and 45 minutes and we are back in action. I’m always hesitant to start pulling molding off because it never seems to go back probably but with your excellent video and tips you would never know it was apart. Very happy that I took your advice and found the all metal handle or I think I’d be doing this all again it a few months. The wife thinks it is a pickup truck so stronger the better. Thanks again and stay safe.
If there was an award for most helpful RUclips video, you should win it with this one. The plastic wrap idea made we weep inside thinking about all the times i've lost nuts down the rabbit hole. I would kiss you on the mouth if I could. Great job!
Great video. I followed this step by step successfully. This saved me hundreds of dollars. The Amazon handle didn’t work for me. I thought my cable was stretched because the Amazon handle wasn’t working. I ended up buying the OEM handle at the dealership then PRESTO, it works like it’s brand new.
Fantastic video - ordered the parts and plan on doing it this week. I did get a quote from my friendly body shop - prices have gone up on dealer handles - over $100 for the part with total job being $300 plus. You have saved me a ton - thank you so much!!
Great video and I just ordered the all metal handle for only $18. I can’t believe Toyota’s is so inferior with the plastic construction. They obviously did it on purpose so, owners would have to dish out the $200 plus to get it fixed at the dealership. I’m going to use this video to fix my door handle as soon as the replacement comes in. Thanks again for an awesome video!
Great video! My only additions would be a reminder to remove the license plate first, AND to check the fit of the latch cable in the new door handle BEFORE installing it. I bought one off Amazon that supposedly fit a 2005 Sequoia, but the gap between where the little metal ball and the plastic indent on the cable sit was too wide, meaning the latch cable was stretched at 'rest' and didn't therefore work. I didn't think to check this before hand since I honestly didn't even know how the latch worked in relation to the cable. Thanks and awesome video! It was the only one I needed.
Thanks for sharing the tips. I realized that I hadn’t mentioned about the license plate since I had mine removed already, but I pinned it in the top comment, hoping that others would see it since I can’t add to the video later, thanks for sharing all of your experiences too.
Spot on! I was able to replace my 2004 handle with the new type handle using your links below! Thanks so much. Toyota charged me $200+ several years ago when it broke the first time.
My Toyota dealership charged me $500 to replace the latch handle 5 years ago. I had to replace the window motor a few years back, so I was already familiar with how to remove the trim. However, that said, this video is excellent as now I know every screw and clip that must come out. Fantastic. 2nd handle since I've owned this. Hopefully with the metal one I won't be replacing it anytime soon. After this I get to go replace my electric telescoping antenna for the 2nd time. BOTH my fault as I don't appear to be smart enough to turn off the radio before I go through the car wash.
Thank you I’m glad if it helped! It’d probably be 700 - 800 nowadays. Hopefully it holds up for you! I’ve never tried going through the car wash with the antenna up but winter time mine is sticking up part way because it’s so cold and frozen.
Just wanted to send you much mahalo and salamat for your video. I followed it step by step with multiple pauses as I navigated the replacement of my 2003 Sequoia rear door handle. I purchased everything you used in your video and I hope the metal door handle lasts as long as the original. I also replaced my brake light bulbs since my hatch opens up now. Thumbs up given and subscribed to your channel!!!
Wow--Thank you Paul! I like to try fixing things myself but don't have a lot of experience to fall back on. There always seems to be more questions than answers. I really appreciate how clear, detailed and applicable your instructions were. The extra hints were great; the plastic to hold the nut in the socket---brilliant! your directions helped me feel confident that I was not going to be taking a half-done project to the mechanic to finish. The fix was a success, and while the panel was off I was able to see that my back-up camera, which hadn't been working for a year, had a severed cable and was able to fix that too. Small victories feel good! I am going to check out some of your other projects...although I do not see a pole barn in my future anytime soon... ;) Thanks again.
Hey Joanne that means a lot thanks for the thoughtful comment and feedback, It means a lot! I’m glad if it was helpful to get the job done. That’s awesome you were able to fix your back up camera too!! Awesome job! You never know on the pole barn house or a shed... 😉
Great vid, the all metal handles can bend, best potential combo is using the metal handle from the aftermarket handle to replace the broken stock plastic hatch handle. The oem is superior aside from the plastic handle.
By far the best DIY video I have ever seen! Thank you for an excellent video. Just bought the parts and am very confident after watching this super clear video.
Thank you I’m glad if it was helpful. Yeah it’s one of those things that just needs to be replaced eventually. It’s one of the only bad things about this GEN I think.
Awesome. Thanks for the step-by-step guide, I had all my tools right because you were so specific at each step. I got it done in about 1 hour. M1y 02 handle stopped working and unlike you, it wasn't plastic... But the cable's metal lever arm pulling the cable was deflecting left right so the latch wouldnt open. It must've been a cheap replacement by the prior owner. Weird but a replacement metal handle assembly fixed it.
I got to tell you. We'll made video. I had to replace this latch about three years ago and the video I followed, didn't remove the license plate housing. That made it more difficult for me since I have big hands. But this time I got it done in less than an hour and working calmly. I appreciate your video very much.
Definitely the best tutorial I've seen for replacing these handles. Everyone else drops the window lift assembly to get to the 2 nuts for the handle. You showed that's one very unnecessary step. The only thing I would say could have been done different is once you removed the covers inside the hatch could have been popped so you didn't have to climb and crawl in and out. Other than that, A+++
@@SmartEasyDIYer heads-up to anyone givining this a try. I just tried to replace mine today and I couldn't get a socket to seat on the bolts for the handle. I'm guessing your setup, with the multiple extensions, had just enough flex in it for the socket to seat on the bolt head. I tried with 1 deep socket and a 6" extension and I just couldn't get the socket to grab the head of the bolt, so I got a universal joint socket adapter. Hopefully that does the trick.🤞🏻
46000 people with the same problem. This will be the second time I’ve replaced this handle. Glad I found the metal one before watching this video. Probably should have bought the body clips too. Anyway great video, thanks!
Thanks for the very well made video. First time changing one of these handles and I had no idea where to even start. Thanks to you though, the job was done quick and stress free.
You cable is bad, replace it and you will never need to buy another handle. It should take one fingers pressure to unlatch. I bought my cable from the dealer, can’t recall what I paid, but it still works great.
Great job of explaining how to fix my handle. Excellent video and instruction! Ordered parts from your websites and they worked perfectly. Thank you Tom
Way to go great job!! They run forever. Yes there’s some links down in the video description below the video and also in the top pinned comment. Thanks
Wow…great video! I felt really confident going into this project! Would have been faster for me if the handle I ordered didn’t need some Dremel modifications for the cable to attach. Also had to widen the screw hole on the sequoia itself so the handle would go back in. Part issue, not a reflection of this video, which as I mentioned was great!! Thank you so much for taking the time and being so thorough!!! Took me an hour and a half… but surely would have been faster without the extras mine took to make it fit right!!
Thank you so much for this easy to follow video. You saved me 100s of dollars. I was able to do it all by myself except for removing the license plate only because the screw was stripped and rusted. 👏
Great video… just changed the latch on my 2001 Sequoia. One thing to add (maybe someone else added this comment) be sure to remove license plate before trying to remove exterior panel.
Paul, this helped me tremendously. Big thanks for taking the time to create and post! Replaced the handle but actuator was bad and had to replace that as well but your video got me through what I needed.
Excellent tutorial! Only issue I had was not removing the license plate, which holds the rear panel on. You video shows yours was off, but no mention of the necessity to remove it (just like the pull handle inside needs to be removed). Thanks!
Yeah thanks I didn’t think to mention it in the video specifically since I already had it off. I pinned it at the top in the comments later hoping everyone would see it. I’m glad you got it!
Great video! Very concise and perfectly detailed. Your tip about using plastic to hold the nut was super helpful, I've never thought of that before. I did break that plastic piece with the threads that holds the key lock in place though, so I'll have to JB Weld that at a later time. Thanks for the great tutorial!
Just completed this fix, unfortunately I had an assembly with a plastic handle… it broke on the third opening… ordered the all metal handle in this video… thanks for the help!
:-( turned out the handle wasn't my issue. I did still replace with the all metal one to prevent the plastic breaking in the future. It seems the issue might be that part with the ball you slip into the handle. My vehicle had an older version of that, and it was difficult to get into the handle, you made that part look so easy! I appreciate you posting this video. I learned a lot, and look forward to trying to fix more things on my own. Issue is,I was finally trying to get my trunk open because I needed to get my brake light fixed. *sigh*
Excellent instructional video for handle replacement. Just ordered the metal handle. Hopefully 3rd handle made of metal will last longer than 5 years. Thank you again!
Excellent video. I used it to change my handle on my 2004 Sequoia. I would add that keeping some WD 40 for those rusted screws on the handle as mine looked like they were the original. Also, when putting the lock nut back on, I used blue painters tape on the outside of the panel to hold it closer so I could easily screw in the bolt. Again thanks for such a great DIY video because it made this job that much easier
Question: I broke the two screw mounts that hold the handle to the license plate panel and now it seems there is too much give and it doesn't pull the cable far enough to release the latch. Thoughts on a possible work around to this problem. Thanks!
Great video! It was extremely helpful, and right to the point with no wasted time. Thanks for the advice and links. I purchased everything in the links and worked great. Thanks!
After replacing the handle multiple times on my 03 Sequoia, each time the handle worked for a while, however the lever pull still required a lot of pressure to unlock. I never thought to replace the cable and latch. When I bought a new cable / latch from the dealer, it was a game changer. I can now open it with one finger. So if you replace the handle but still have to pull hard to unlatch, replace the cable and latch and this issue will go away. It has been 4 years and the handle still only takes one finger pressure. Try this.
Since you already open up rear plate assembly area, why not wipe it clean b4 re-installing. Suggestion only! I like my Sequoia neat & clean. 😊 Great instructions video Paul, I salute you.
Thanks for the help only part I got consumed on was taking off the license plate. I got everything loose for the inside but the exterior wasn’t loose. I figured maybe if I take the license plate off then it will come loose. Thanks for the great video!
When you take the interior panel off, don’t pull from the side corners, you will break the top window seal. Instead, simply pull it up and out towards the roof. Really important. Reverse for installing.
Just followed these instructions, using the parts in the links and it went perfectly! Thanks for a great video. The only advice I would give is then you are removing the outside panel [4:40], its easy to snap the plastic part that holds the screw for the key lock cylinder like I did. Its only a screw embedded in plastic, so be very careful when you lift the whole assembly out.
Unfortunately, I snapped both screws and it now seems like there is too much give when pull the latch to release the latch. Is there a workaround after breaking those two mounts?
It is the cable that is bad… After doing this job 3 times, I got a new cable from the dealer and was shocked that it requires only the pressure of one finger to unlatch my lift gate.
Good job! What a shame Toyota has not corrected this “plastic” weakness in their design. Got an aftermarket metal one too, definitely outlasted the original by YEARs- 2001 model- still running strong!
Thank you for this video. We were able to do this this weekend and my husband successfully changed the latch handle. However he did leave one screw in or something so we hear it rumbling when we open lol 😁 Wanted to know if you ever had issues with the drivers side door not flush when it closes? Again thank you for the content.
You’re welcome. I’m glad you got it! Yes it’s easy to lose a screw in there. Lol. I’ve never had the other doors not close flush but I think you can usually adjust a little where it latches. You can see if that’s loose at all.
11:00 Got her done with the help of some JB weld plastic Bond. A few places broke because screws were rusted into the plastic. Thank you for the video. I am a 70-year-old woman and after watching this video I am fixing the back hatch latch all by myself thank you so much
Awesome great job!!
My youngest son and I fixed our 2001 latch--great directions~ It took us a couple of hours--not as automotively gifted as you--thanks so much!!!
Awesome great job!! Sounds like a good project to bond on 😁
It's January 2024 and this video did the trick for me. 2006 4WD Sequoia. As others mentioned, the plastic wrap in the socket was a great trick!
Awesome! Thanks for letting me know.
August 2024. Used this video as a step-by-step on my broken 2006 Sequoia door handle. Latch broke in the exact same spot. Great hack with the plastic wrap. Bought everything you recommended and fixed it for less than $50! Thank you Thank you Thank you! 🎉
Wow, awesome way to go! Thanks for letting me know. I’m glad it worked out for you! 🤛
I have watched many diy videos to learn how to fix my vehicles. Your video is by far the best one I've seen. I'm a 56 yr old woman, and not afraid to save some money by fixing things myself. I have gotten very frustrated with videos where they expect you to know technical terms or where a part goes and they don't show the one critical step you need to do, like they think I'm a mechanic! (If i were a mechanic i wouldn't be watching the videos.)
But this video was so clear, easy to follow along, and showed every step. I just ordered the parts from your links and i know because of you I'll have my back door opening again as soon as they get here.
Thanks so much for taking the time to make this video!
Thank you so much for the kind words Gail. I appreciate the feedback on the video. I’m so proud of you for doing this yourself. Hopefully everything goes smoothly I’m sure you’ll do great!
Paul, I replaced the broken latch handle on my '02 Sequoia using this video as a guide, as well as ordering my new latch handle and the green things from the links you provided. As several others mentioned, your little trick of using a piece of the plastic wrapper to hold the nut in the socket worked perfectly. What a fine tutorial! Thanks for posting it. For any who are going to be doing this to your Sequoia, let me add a few tips:
The lift gate pull attachment referred to at about :50 in the video is normally covered by a plastic trim piece. This is removed by a forceful upward lift on the trim piece.
Take note of the orientation of the lock pictured at 4:28 and 9:23 before removing that nut. The lock tab should be installed between the plastic piece on the outside that you're removing, and the sheet metal of the lift gate. I believe on Paul's Sequoia, this had been pulled apart previously and reassembled incorrectly. Once apart, you may note that there is a cut out in the plastic piece designed to hold the lock in place and relieve any gap between it and the plastic piece. If you screw up like I did, JB Weld works very well to repair the damage done to the plastic piece.
Finally, as mentioned, the green things are too big. I found that they were very easy to cut down with a razor knife, and work well if you do so.
Cheers!
Hey Lyle thank you so much for sharing your tips and tricks with others! My Sequoia may very well may have been worked on in the past And put back in correctly i’m glad you shared your experience with the rest of us. Thank you for the support and I’m glad you got it fixed. 👊
You MUST remove the license plate for the back trim piece to be removed. Other than that, excellent video!
You made fixing my 2005 Toyota Sequoia rear liftgate handle absolutely EASY! Your instructions were so good that even I could do it! Thanks for the great video!
Awesome and great job thanks for letting me know!!
Annnd...this is why, even though I've been a mechanic in various field since 1972, that I always watch ALL of a DIYer's videos even though they might not be at all pertinent to my life. There is almost always some tidbit of a mechanic's trick to learn from everyone. That trick about covering the nut with the plastic sheeting to keep it tight in the socket was a real beaut. I'm 65 now and you can never tell when some helpful hint can come in handy. Thanks for putting this up!
Hey thanks so much for the comment I really appreciate it!! I like watching videos as well and learning tricks of how people do stuff. There’s always something to learn. 😊
My compliments on a very well made video. No time wasted on unimportant information. Very helpful and well done. Thank You !
Thank you I appreciate the feedback!
My compliments on a great compliment.
Yes, this guy knows his stuff😊👍🏾
Mine just broke. I need to order but will be rewatching this video while awaiting the parts ❤
Good luck with it! I hope it goes well.
Fixed the latch handle on my 07 Sequoia following these instructions. Pretty easy. Took about an hour total considering I didn't know what I was doing and didn't want to break anything. Only spent about $45 getting the part, recommended tools and replacement fasteners. Saved myself hundreds of dollars probably doing it myself. Thanks man!!
Awesome great job! I’m sure you saved a lot. 😊👍
Great tips and awesome trick with the little plugs on there! I’ve pulled my Sequoia apart 25 times and never knew they were there for that!!
Thanks I’m glad you found it helpful! 😊
This video was extremely helpful and well put together. I have an '04 Sequoia and this is the second latch to break. First was replaced by the dealer so I had no idea where to start. This video definitely helped.
I will state that we had an issue taking off the license plate part. found out that the license plate needed to be removed before the part would finally come loose. After that we were done within about 30 minutes.
Thanks!
Awesome I’m glad you got it! Yes I forgot to mention in the video since I had mine off already. I pinned it to top comment hoping more would see it too. Glad you got it! Thanks
After watching this video I couldn't wait to fix my handle which I did within 20 minutes. By far the best video with easy step by step instructions. Cheers.
Awesome thanks for letting me know! I’m glad you got it fixed! Great job!
Probably one of the best instructional videos I’ve watched as far as to the point, in depth for the layman, care in presentation. Impressed!
Thanks Derek I appreciate you letting me know!
My latch has been broken for almost 8 years. I put it off this long and last week broke my taillight so i had to fix it. Very good video was a much easier fix that i thought! Thank you
Wow that’s crazy you put up with it that long!! I’m glad you got it fixed it will feel like a whole different vehicle probably lol
I think I’m clocking about five years 😅 Will be showing my husband this video ASAP
Wow long time! Good luck with swapping it. 😁
The best video I’ve seen with full detail, my 2003 Sequoia rear handle been broken for years...now a must fix. Thank you
Wow thank you!! I’m so glad if it was helpful. That’ll be awesome to have it working again!
Just installed new one all metal
Thanks again. God bless
Awesome great job! Thank you 🙏
Not mentioned in video (unless I'm deaf), take the license plate bolts out!! Otherwise panel wont pop out on top.
Yes, thanks for the comment. I hadn’t thought to mention it when I made the video because I already had it removed ahead of time but I pinned it in the top comment hoping others would see it first. Since I can’t add it to the video later. Thanks
That part got me the first time...
Thank you!
Yeah I was yanking it so hard, I broke off the key assembly
I watch a ton of DIY videos especially now when money is super tight but I’ve never taken the time to comment but felt this one deserved it. $16 and 45 minutes and we are back in action. I’m always hesitant to start pulling molding off because it never seems to go back probably but with your excellent video and tips you would never know it was apart. Very happy that I took your advice and found the all metal handle or I think I’d be doing this all again it a few months. The wife thinks it is a pickup truck so stronger the better. Thanks again and stay safe.
Wow awesome that means a lot! Thanks for letting me know. Great job getting it replaced!! 👊
@@SmartEasyDIYer The GD cable fells off!! I'm going to have to repeat the whole procedure huh?
Looking at purchasing an '07, with a non-opening tailgate. Great video.
Thank you. They have this common issue but otherwise they’re a very solid rig.
Thanks a million. I just finished installing my new all metal latch. With your awesome step way step we’ll explained video. Saved me $$$ and headache
Just had to say thanks so much and blessings upon you🙏🏻
Hey that’s awesome thanks so much for letting me know I really appreciate it!! Great job on your replacement! It’s so fun to have them working again.
If there was an award for most helpful RUclips video, you should win it with this one. The plastic wrap idea made we weep inside thinking about all the times i've lost nuts down the rabbit hole. I would kiss you on the mouth if I could. Great job!
Bahhahaha we can spare the kisses but I’m glad it helped you! Sometimes it’s the little tricks that save a lot of pain 😁
Great video. I followed this step by step successfully. This saved me hundreds of dollars. The Amazon handle didn’t work for me. I thought my cable was stretched because the Amazon handle wasn’t working. I ended up buying the OEM handle at the dealership then PRESTO, it works like it’s brand new.
Wow good for you I’m glad that worked out for you. Hopefully the oem does well for you.
Fantastic video - ordered the parts and plan on doing it this week. I did get a quote from my friendly body shop - prices have gone up on dealer handles - over $100 for the part with total job being $300 plus. You have saved me a ton - thank you so much!!
Awesome I’m so glad. Good luck with it.! Just make sure to remove the license plate first. 😁
Great video and I just ordered the all metal handle for only $18. I can’t believe Toyota’s is so inferior with the plastic construction. They obviously did it on purpose so, owners would have to dish out the $200 plus to get it fixed at the dealership. I’m going to use this video to fix my door handle as soon as the replacement comes in. Thanks again for an awesome video!
You’re welcome. Yes hopefully they learned after this gen. This is a very common problem I’m finding out. Good luck with your repair!
Totally what I needed!! This video is worth money!!! Thank you Thank you
Thank you for letting me know I’m glad it was helpful!! Best of luck with your repair!
Great video! My only additions would be a reminder to remove the license plate first, AND to check the fit of the latch cable in the new door handle BEFORE installing it. I bought one off Amazon that supposedly fit a 2005 Sequoia, but the gap between where the little metal ball and the plastic indent on the cable sit was too wide, meaning the latch cable was stretched at 'rest' and didn't therefore work. I didn't think to check this before hand since I honestly didn't even know how the latch worked in relation to the cable. Thanks and awesome video! It was the only one I needed.
Thanks for sharing the tips. I realized that I hadn’t mentioned about the license plate since I had mine removed already, but I pinned it in the top comment, hoping that others would see it since I can’t add to the video later, thanks for sharing all of your experiences too.
Spot on! I was able to replace my 2004 handle with the new type handle using your links below! Thanks so much. Toyota charged me $200+ several years ago when it broke the first time.
Awesome I’m glad it was helpful thanks for letting me know! Great job.
@@SmartEasyDIYer Thanks, new subscriber to your channel.
Thank you I appreciate the support!
My Toyota dealership charged me $500 to replace the latch handle 5 years ago. I had to replace the window motor a few years back, so I was already familiar with how to remove the trim. However, that said, this video is excellent as now I know every screw and clip that must come out. Fantastic. 2nd handle since I've owned this. Hopefully with the metal one I won't be replacing it anytime soon. After this I get to go replace my electric telescoping antenna for the 2nd time. BOTH my fault as I don't appear to be smart enough to turn off the radio before I go through the car wash.
Thank you I’m glad if it helped! It’d probably be 700 - 800 nowadays. Hopefully it holds up for you! I’ve never tried going through the car wash with the antenna up but winter time mine is sticking up part way because it’s so cold and frozen.
Just wanted to send you much mahalo and salamat for your video. I followed it step by step with multiple pauses as I navigated the replacement of my 2003 Sequoia rear door handle. I purchased everything you used in your video and I hope the metal door handle lasts as long as the original. I also replaced my brake light bulbs since my hatch opens up now. Thumbs up given and subscribed to your channel!!!
Thank you so much for letting me know I’m glad it was helpful and I appreciate the support!! Nicely done.
You are as good of a teacher as Car Care Nut Guy vedios. Good Job.
Thanks. I don’t know who that is but I’ll take it as a good thing. 😁
Wow--Thank you Paul! I like to try fixing things myself but don't have a lot of experience to fall back on. There always seems to be more questions than answers. I really appreciate how clear, detailed and applicable your instructions were. The extra hints were great; the plastic to hold the nut in the socket---brilliant! your directions helped me feel confident that I was not going to be taking a half-done project to the mechanic to finish. The fix was a success, and while the panel was off I was able to see that my back-up camera, which hadn't been working for a year, had a severed cable and was able to fix that too. Small victories feel good! I am going to check out some of your other projects...although I do not see a pole barn in my future anytime soon... ;) Thanks again.
Hey Joanne that means a lot thanks for the thoughtful comment and feedback, It means a lot! I’m glad if it was helpful to get the job done. That’s awesome you were able to fix your back up camera too!! Awesome job! You never know on the pole barn house or a shed... 😉
Pole barn? I have a o1 sequoia and don’t know what pole your talking about
I think she probably was talking about some of my other videos where I did a pole barn house build etc.
Great vid, the all metal handles can bend, best potential combo is using the metal handle from the aftermarket handle to replace the broken stock plastic hatch handle. The oem is superior aside from the plastic handle.
Thanks. They could be Ive never tried it.
By far the best DIY video I have ever seen! Thank you for an excellent video. Just bought the parts and am very confident after watching this super clear video.
Thanks Stuart I appreciate you letting me know! Best of luck!!
I’m on my 3rd replacement handle. Even the metal breaks...unfortunately. Great video. I needed a refresher.
Thank you I’m glad if it was helpful. Yeah it’s one of those things that just needs to be replaced eventually. It’s one of the only bad things about this GEN I think.
Great video! I have used it twice to replace the latch on my wife's 2007 Sequoia. Thank you.
You’re welcome. 👍
This video was an absolute life saver. Repair went off with minimal mishaps. Took me just over an hour 😅 Thanks!!!!
Very nice! Great job!
Awesome. Thanks for the step-by-step guide, I had all my tools right because you were so specific at each step. I got it done in about 1 hour. M1y 02 handle stopped working and unlike you, it wasn't plastic... But the cable's metal lever arm pulling the cable was deflecting left right so the latch wouldnt open. It must've been a cheap replacement by the prior owner. Weird but a replacement metal handle assembly fixed it.
Nice job! Glad it helped.
I got to tell you. We'll made video. I had to replace this latch about three years ago and the video I followed, didn't remove the license plate housing. That made it more difficult for me since I have big hands. But this time I got it done in less than an hour and working calmly. I appreciate your video very much.
Thank you I appreciate you letting me know! I’m glad it went well.
Definitely the best tutorial I've seen for replacing these handles. Everyone else drops the window lift assembly to get to the 2 nuts for the handle. You showed that's one very unnecessary step. The only thing I would say could have been done different is once you removed the covers inside the hatch could have been popped so you didn't have to climb and crawl in and out. Other than that, A+++
Thank you I appreciate it!
@@SmartEasyDIYer heads-up to anyone givining this a try. I just tried to replace mine today and I couldn't get a socket to seat on the bolts for the handle. I'm guessing your setup, with the multiple extensions, had just enough flex in it for the socket to seat on the bolt head. I tried with 1 deep socket and a 6" extension and I just couldn't get the socket to grab the head of the bolt, so I got a universal joint socket adapter. Hopefully that does the trick.🤞🏻
Yes hopefully so! Good luck with it.
46000 people with the same problem. This will be the second time I’ve replaced this handle. Glad I found the metal one before watching this video. Probably should have bought the body clips too. Anyway great video, thanks!
Haha it’s a very common problem with this Gen. good luck I hope it goes well!
@@SmartEasyDIYer it did not this time. Had to replace the cable too
Ok I’m glad you figured it out ok.
Thanks for the very well made video.
First time changing one of these handles and I had no idea where to even start.
Thanks to you though, the job was done quick and stress free.
Awesome thanks for letting me know!
That was a most excellent video on the handle replacement. I don't have a Sequoia but plan on getting one. Great job!
Thank you! They are excellent rigs.
Nice & logical video.... step by step. I'm replacing this latch for the second time on an '05 so I' m always glad to see a refresher course.
Thank you I hope it goes better this time around!
You cable is bad, replace it and you will never need to buy another handle. It should take one fingers pressure to unlatch. I bought my cable from the dealer, can’t recall what I paid, but it still works great.
Great job of explaining how to fix my handle. Excellent video and instruction! Ordered parts from your websites and they worked perfectly. Thank you Tom
Awesome great job Tom. I’m glad you got it fixed.!
Thank you for the tutorial . The best simple to the point , thorough explanation.
Thank you Eric!
Just finished my latch for my 2003 Sequoia with 370,000 miles. Thanks for the tips. You mentioned a link for the clips , etc
Way to go great job!! They run forever. Yes there’s some links down in the video description below the video and also in the top pinned comment. Thanks
Wow…great video! I felt really confident going into this project! Would have been faster for me if the handle I ordered didn’t need some Dremel modifications for the cable to attach. Also had to widen the screw hole on the sequoia itself so the handle would go back in. Part issue, not a reflection of this video, which as I mentioned was great!! Thank you so much for taking the time and being so thorough!!! Took me an hour and a half… but surely would have been faster without the extras mine took to make it fit right!!
Thanks so much! I’m glad you’re install went smoothly overall despite having some setbacks. Thanks for the input.
Thank you so much for this easy to follow video. You saved me 100s of dollars. I was able to do it all by myself except for removing the license plate only because the screw was stripped and rusted. 👏
Awesome I’m so glad you got it! Great job!!
Thanks for a great video and instruction, my brother's handle just broke. Patience and your video will get it done!!
You’re welcome! Good luck with it. 👍
Great tutorial! Worked perfect and the one I bought works amazing! Can't believe how much better it works. That old one was a piece of trash lol
Haha thanks I’m glad it worked!
Thank you sooooo much! Just save me and my family some money!! Totally installed and ready to go. So grateful for this video.
Thanks for letting me know and great job!!
Great video… just changed the latch on my 2001 Sequoia. One thing to add (maybe someone else added this comment) be sure to remove license plate before trying to remove exterior panel.
Thanks. Yes others have mentioned it. I added it to my top comment as well. Lol
Paul, this helped me tremendously. Big thanks for taking the time to create and post! Replaced the handle but actuator was bad and had to replace that as well but your video got me through what I needed.
Hey you’re welcome I’m glad it helped!! Great job!! Thanks for letting me know!!
Excellent tutorial! Only issue I had was not removing the license plate, which holds the rear panel on. You video shows yours was off, but no mention of the necessity to remove it (just like the pull handle inside needs to be removed). Thanks!
Yeah thanks I didn’t think to mention it in the video specifically since I already had it off. I pinned it at the top in the comments later hoping everyone would see it. I’m glad you got it!
Great video! Very concise and perfectly detailed. Your tip about using plastic to hold the nut was super helpful, I've never thought of that before.
I did break that plastic piece with the threads that holds the key lock in place though, so I'll have to JB Weld that at a later time.
Thanks for the great tutorial!
Thank you for letting me know! Great job!!
Just completed this fix, unfortunately I had an assembly with a plastic handle… it broke on the third opening… ordered the all metal handle in this video… thanks for the help!
You’re welcome!
:-( turned out the handle wasn't my issue. I did still replace with the all metal one to prevent the plastic breaking in the future. It seems the issue might be that part with the ball you slip into the handle. My vehicle had an older version of that, and it was difficult to get into the handle, you made that part look so easy! I appreciate you posting this video. I learned a lot, and look forward to trying to fix more things on my own. Issue is,I was finally trying to get my trunk open because I needed to get my brake light fixed. *sigh*
Sorry for the issues you had. Maybe this video would help you ruclips.net/video/usRoKLzlOj4/видео.html
@@SmartEasyDIYer Thank you! I will try some of the things I saw in the video link you gave me. I appreciate your time!
You’re welcome. Good luck with it!
Excellent instructional video for handle replacement. Just ordered the metal handle. Hopefully 3rd handle made of metal will last longer than 5 years. Thank you again!
You’re welcome good luck with it!!
Excellent video. I used it to change my handle on my 2004 Sequoia. I would add that keeping some WD 40 for those rusted screws on the handle as mine looked like they were the original. Also, when putting the lock nut back on, I used blue painters tape on the outside of the panel to hold it closer so I could easily screw in the bolt. Again thanks for such a great DIY video because it made this job that much easier
Thanks! I’m glad you got it. Thanks for sharing your tips with others.
Great video, couldn’t find the link for metal handle. Looking forward to having this work again!!
Thanks. It should be in there video description below the video. bit.ly/SequoiaRearHandle
I’ll post it here too. I hope you can get it working!
Thank you very much, Paul! I saved my step-dad a few bucks by doing this for him. He really appreciates it!
You’re welcome! I’m so glad you got it done for him.
Question: I broke the two screw mounts that hold the handle to the license plate panel and now it seems there is too much give and it doesn't pull the cable far enough to release the latch. Thoughts on a possible work around to this problem. Thanks!
Great video! It was extremely helpful, and right to the point with no wasted time. Thanks for the advice and links. I purchased everything in the links and worked great. Thanks!
Awesome thanks for letting me know I’m glad it worked out!!
After replacing the handle multiple times on my 03 Sequoia, each time the handle worked for a while, however the lever pull still required a lot of pressure to unlock. I never thought to replace the cable and latch. When I bought a new cable / latch from the dealer, it was a game changer. I can now open it with one finger. So if you replace the handle but still have to pull hard to unlatch, replace the cable and latch and this issue will go away. It has been 4 years and the handle still only takes one finger pressure. Try this.
Thanks for sharing your experience. I ended up replacing my cable as well a year or 2 after the handle.
Can you pin my comment to the top, it will save people a lot of recurring pain. Thanks, great video.
Can you place a link for the cable as well? Thanks for a great video and saving me $$
@richard8995 bit.ly/RearCable here you should be able to find the cable. Good luck with yours.
Omg..I have a 2002 Sequoia and my handle broke as well. My price quote was $800+ to fix it! THANK YOU for this video!!
Wow that’s a lot! I believe it though. It adds up quickly. Good luck with fixing it!
Since you already open up rear plate assembly area, why not wipe it clean b4 re-installing. Suggestion only! I like my Sequoia neat & clean. 😊 Great instructions video Paul, I salute you.
Thank you! I would if it was enough to be a problem with installation, but I live on a dirt road so for me it’s kind of pointless lol.
Awesome tutorial. Very easy to follow. You saved a poor grad student a lot of money on this one, so thanks!
Awesome I’m glad it helped! Thanks
Great and easy to understand video with awesome camera angles.
Thank you for letting me know!
Bro! I did it!!! I fixed my latches!!! Thanks man!!! I appreciate this tutorial!!!! Woow
Awesome good for you great job!!!
Awesome video man. Helped me get my sequoia fixed. Thanks so much for posting!!!
Thank you Jacob I’m glad it helped! 👊
Great video. Perfect step by step instructions and very helpful hints.
Thank you. Just make sure to remove the license plate first. 👍
This video literally saved me $600 thanks a ton for this content!
Wow that’s awesome to hear! Nice job. 👍
Thanks for the help only part I got consumed on was taking off the license plate. I got everything loose for the inside but the exterior wasn’t loose. I figured maybe if I take the license plate off then it will come loose. Thanks for the great video!
You’re welcome I’m glad if it was helpful!
Great video, this just helped me fix this exact issue and I had bought the same new metal handle ahead of time, which is working great. Thanks!
Awesome glad to hear! Thanks
My husband just ran the cord beside the broken handle. Works perfectly fine!
Ok great
Excellent and straight forward video !!!!
Thank you Francisco! I appreciate you letting me know.
When you take the interior panel off, don’t pull from the side corners, you will break the top window seal. Instead, simply pull it up and out towards the roof. Really important. Reverse for installing.
Thanks for sharing your experience.
Great camerawork on this video above all else
Thank you I appreciate the feedback!
Huge help. Best video on this job on youtube. thanks
Thank you!
Great video. Saved me a lot of guess work today replacing my latch. Thanks for making this a 20 minute job man. Really solid work on your end.
Thank you I appreciate you letting me know!
Just followed these instructions, using the parts in the links and it went perfectly! Thanks for a great video. The only advice I would give is then you are removing the outside panel [4:40], its easy to snap the plastic part that holds the screw for the key lock cylinder like I did. Its only a screw embedded in plastic, so be very careful when you lift the whole assembly out.
Awesome great job! Thanks for sharing your experience with the rest of us.
Unfortunately, I snapped both screws and it now seems like there is too much give when pull the latch to release the latch. Is there a workaround after breaking those two mounts?
Just finished replacing my fourth handle, still need to take a peek to see how some of that plastic comes off, thanks for the video!
You’re welcome. I hope your next one goes well. Have you tried the all metal handle?
It is the cable that is bad… After doing this job 3 times, I got a new cable from the dealer and was shocked that it requires only the pressure of one finger to unlatch my lift gate.
A simple paint can opener with the hooked end can be used to get behind the trim pieces to pop them out. No special tools required.
I could see that would work!
Thank you for a great video and very well explained. I will get to it as soon as I get the metal one. Thanks again.
Thank you for letting me know I appreciate it! Good luck with your swap.
A big thanks to you Paul. You saved me some big bucks.
Awesome glad to hear!
Best instructions on this fix!! Great job!!
Thank you for taking your time to share thus information. It helped me in troubleshooting.....
God bless
You’re welcome! Thanks for letting me know.
Good video, just going out to replace my latch now on my 02 White Sequoia Limited... :) cheers
Thank you. Good luck!
Thanks a million Paul. Your fix worked like a charm and while I was there even fixed the window not rolling down. Great video and instructions.
Awesome I’m glad it worked. Great job!!
Awesome video! Thank you for posting it. Saved me time and money.
Awesome I’m so glad I love it when people save money fix it themselves!! Thanks for letting me know. 😊
Great video ! No pets/kids in the way distracting your guidance. Also no annoying background music to interfere with your audio instructions.
Thank you! I appreciate you letting me know.
Great instructions. I’m not a car guy at all and was able to do this no problem.
Awesome thanks and great job!!
I follow this video step by step.Thank you i really appreciate you sir.
Thank you for letting me know. I am glad it worked!
Good job! What a shame Toyota has not corrected this “plastic” weakness in their design. Got an aftermarket metal one too, definitely outlasted the original by YEARs- 2001 model- still running strong!
Thanks. Glad you fixed yours. Yes it seems to be the weakness for sure. Besides some minor things these cars run forever though.
Inherited this SUV from family , I just repaired it and it all went well,
thank you ,
Ron
Awesome Ron thanks for letting me know!
Super-helpful video. One addition: the license plate must be removed (figured that out after a few trips in and out of the car :) )
Thanks. Yes I had mine off already so I didn’t think to mention it
Thanks for he video. Incredible amount of information and very helpful. Thank you for sharing!!
Awesome I’m glad if it helped. You’re welcome. 😊
This helped me out tremendously thank you keep up the good work
Thank you for letting me know!
You’re awesome man thank you!! Dealer wanted 150 for this installation
Thanks I’m glad you got it replaced!
Thank you for this video. We were able to do this this weekend and my husband successfully changed the latch handle. However he did leave one screw in or something so we hear it rumbling when we open lol 😁
Wanted to know if you ever had issues with the drivers side door not flush when it closes?
Again thank you for the content.
You’re welcome. I’m glad you got it! Yes it’s easy to lose a screw in there. Lol. I’ve never had the other doors not close flush but I think you can usually adjust a little where it latches. You can see if that’s loose at all.