How To Rebuild A Car Engine (4G63)
HTML-код
- Опубликовано: 29 мар 2021
- Evo 8 4G63 Engine Rebuild
» vasyn.com «
Engine Parts Used:
Pistons: bit.ly/3tuL3sW
Rods: bit.ly/3tsZcGY
Valve Springs: bit.ly/3azlJsT
Valve Seals: bit.ly/2MVKKWY
Cams: bit.ly/2MYpdgg
Head Studs: bit.ly/3o8RKNF
Main Studs: bit.ly/2JzkYGj
Main Bearings: bit.ly/2N3qcvK
Rod Bearings: bit.ly/2YSiY0A
Gasket Kit: bit.ly/3fQpBb8
Balance Shaft Delete: bit.ly/39LLlna
Tools Used:
SK Tools: bit.ly/3mdXhSl ("DVNIEMELA" 25% off)
Outside Micrometer Set: amzn.to/31zOTEm
Bore Gauge: amzn.to/3wdMGwf
Calipers: amzn.to/2PoqdvM
Snap T's: amzn.to/39rcg7c
Brake Cleaner: amzn.to/3m3hX0m
Shop Towels: amzn.to/3ft2Bkg
Ring Filer: amzn.to/2PnCoZZ
Ring Compressor: amzn.to/3weHt7h
Assembly Lube: amzn.to/3wfWsxM
Sealant: amzn.to/3fA19N0
• Blue Evo 8 Parts List: bit.ly/3s0vGXm
➢ Engine
Chag Tuned: bit.ly/2EOHdpM
Pistons: bit.ly/3tuL3sW
Rods: bit.ly/3tsZcGY
Valve Springs: bit.ly/3azlJsT
Valve Seals: bit.ly/2MVKKWY
Cams: bit.ly/2MYpdgg
Head Studs: bit.ly/3o8RKNF
Main Studs: bit.ly/2JzkYGj
Main Bearings: bit.ly/2N3qcvK
Rod Bearings: bit.ly/2YSiY0A
Gasket Kit: bit.ly/3fQpBb8
Balance Shaft Delete: bit.ly/39LLlna
Clear Cam Cover: ebay.to/2SyL3bA
Oil Cooler: bit.ly/39qJHaZ
Plugs: bit.ly/39xvfOi
Throttle Body Seals: bit.ly/2VhFBcQ
Radiator: amzn.to/2MSkFbp
Coil System: bit.ly/2T1v1H3 "dvniemela10"
Full Hardware Kit: bit.ly/2FyiaEo "dvniemela10"
Exhaust Studs: bit.ly/39T67iC "dvniemela10"
Cam Sensor Shield: bit.ly/2tDQPhe "dvniemela10"
Radiator Brackets: bit.ly/2N7fLVs "dvniemela10"
Strut Tower Hardware: bit.ly/2N20RzF "dvniemela10"
Motor Mount Hardware: bit.ly/2R1IVpS "dvniemela10"
Thermostat Hardware: bit.ly/2s5J4Ad "dvniemela10"
➢ Turbo/Fuel
Turbo Kit: bit.ly/39Ps2to
Tactrix Cable: ebay.to/3c1Z5ff
EBCS: bit.ly/3ltbbih
Intercooler: bit.ly/3qh8xzN
Intercooler Piping: bit.ly/39oVYN4
Injectors: bit.ly/3cCEH4B
Fuel Pump: bit.ly/2VkRgYq
Intake: bit.ly/2VkRleG
AFPR: bit.ly/3fnY3sL
4 Bar MAP: bit.ly/36lVqFE
EBCS Harness: goo.gl/NWiRba
EGR Plate: ebay.to/30rm38N
➢ Brakes/Suspension/Drivetrain:
Coilovers: bit.ly/ysrcoils "dvniemela"
Wheels: ebay.to/3caI28I
Tires: ebay.to/2FRYQVL
Lug Nuts: ebay.to/3cfH8Yv
Front Spacers: ebay.to/2FxQHGA
Rear Spacers: ebay.to/30maIXx
Clutch: bit.ly/3mCBB2R
Flywheel: bit.ly/399v6ju
Brake Pads: bit.ly/3fQrdSe
Brake Rotors: bit.ly/39oWA5k
Shifter: bit.ly/33vUsoJ
Clutch Stopper: bit.ly/3oaKcd9
Shifter Base Bushings: bit.ly/3mkcPnP
Shifter Cable Bushings: bit.ly/3fQrzs2
➢ Exterior
Demon Eyes: bit.ly/2DZ2UjV"dvniemela15"
Blue Vinyl Wrap: amzn.to/3bOJiOu
Black Roof Wrap: amzn.to/33pPrgx
LH Inner Fender: bit.ly/3lpLxv4
RH Inner Fender: bit.ly/3qeWTWm
Tail Lights: ebay.to/3krWdcg
Front Lip: ebay.to/2X2JthC
Side Skirts: ebay.to/2OoAya1
Diffuser: bit.ly/2MfZbF5 "dvniemela10"
Bumper: bit.ly/3peJi0d
Vortex Generator: ebay.to/3hNoWqt
Power Brace: ebay.to/30nRC3n
➢ Interior
Braum Seats: bit.ly/3pOonSb "dvniemela"
Evo X OEM Fusible Link: bit.ly/39AoRpL
Evo X OEM Cover: bit.ly/3o4m4sG
Evo X OEM Joint Connector: bit.ly/3mpQipI
AFR Gauge: bit.ly/2HTdPjM
Oil Pressure Gauge: bit.ly/3mp4PSH
Boost Gauge: bit.ly/39viALG
Tint: goo.gl/qQREyR
LED Bulbs: goo.gl/YMjYwG
Radio: amzn.to/2Y9STJK
Double Din Dash Kit: ebay.to/2Y7h5N1
Steering Wheel Wrap: ebay.to/2MmhFnh
Heater Gears: amzn.to/38eTKfk
Heater Cable: amzn.to/38nxPTr
Ignition Switch: amzn.to/2RriXfF
Knob: amzn.to/35BAua7
Battery: amzn.to/2N1UBYD
Power/Ground Wire: amzn.to/2T0LKdl
• Instagram: / dvniemela
• Facebook: / dvniemela
• Sponsors: (Discount Codes)
JDCustomsUSA: bit.ly/2MX0mW4 "DVNIEMELA10"
avalonking.com/ref/dvniemela (DEVIN25)
SK Tools: bit.ly/3mdXhSl (DVNIEMELA)
IAA: bit.ly/3cMmRKk (DEVIN2020)
litlightz.com (DVNIEMELA15)
www.braumracing.com (DVNIEMELA)
aprperformance.com
www.prismaticpowders.com
www.maperformance.com
Just a heads up, for anyone doing a timing belt job on a 4G63, you set the timing and tensioner, you then turn the motor over 3 full times and let it sit for 10 minutes or so. After 10 minutes, check your timing markings on everything and pull the grenade pin on the tensioner. It should slide in and out no problem. You can go a further step and turn the motor over another 3 times with the grenade pin out and then slide the pin in and out to double check that your tension is properly set.
I sat here and watched the hole thing and didn’t even realize how long this was lol 😂
Oh my God... 51 minutes! I need a lot of coffee.. 1am already in here.
I usually watch the 25 min vids during cardio. Can’t wait to feel dead after this 50 mins
I built one of these with a friend. Never tore a motor out a car in our lives. Had the Haynes book and went to town. Stock pistons and rods just all new bearings and gaskets. Didn’t do any clearance checks , didn’t check gaps , bolted up a big turbo and other bolt ons. Car went on to make 460hp for 4-5 years of abuse daily. Wish I could say the same about everything else. Think that car went through like 5 transmissions.
What gator did to that at the end, I haven’t laughed that hard in a while. I’m in tears. Lol
“500 wheel. Nothing crazy” you know that’s pretty crazy to me
This man releases a movie 😂 I love it.
People pay 20-40k for trade school to learn how to do motor work and Devin out here teaching us boys how to do it. Class is in section everyone!!!!!! Awesome video Devin. Very detail and clear appreciate the knowledge
Outside of Jay from Real St building a 2jz, this is the only time I’ve watched a full rebuild, good stuff.
i must say you inspire me alot, i paint cars for a living, and know nothing about engines, but after following you for a long time i whent out and bought a boat project, i dont have the money for an evo (wish i had an evo 9) i got a little help, but i have now renovated my 7.4 v8 big block and it sounds insane. soon i will be putting the engine in the boat.
I am rebuilding a 6A13TT and this video was incredibly valuable as it didn't skip a bunch of steps and detailed all the work you could feasibly do out if a typical home garage.
I rebuilt a 4g69 for my automotive class at my college and the similarities are almost identical, this was addicting to watch!
Love the engine builds, makes me wanna try my own build. great work 💪
Damn clicked on it so fast that it didn’t even load the first time
Thank god I went to UTI cause now I understand everything you do !
This video made me find your channel. I was building my DSM first car motor build, and I neede to see somebody who actually showed what they were doing and showed the results. I've been watching your videos ever since. This evo is bonkers, I cant believe the 6 speed held it so long.
So happy now. Had withdrawal sickness
I just grenaded my evo 8 last week. I am pretty mechanically inclined and have assembled motors before, but never a 4G63. This video gave me the confidence and drive to build this engine myself. Thank you sir!
Im currently in the process of rebuilding my F20c for my Ap1. and this in depth build video helped me understand the whole process better, very informative video. I know we have 2 different motors but the rebuild process/concept is the same as far as steps go. Thank you for your patience and for taking the time to record this for those like me, SUPER good luck on your build in the future to come and let that shit rippp one time real hard for me! ‘Love all the way from that Houston Texas maneeee!