Dude, been stranded in Warmington Delaware for an hour now when I found this video. Code was “no trAn” “EnG 0” “bH 33” “diAG 3” I had pulled away from a light with no power, no speedometer, figured ECM might need rebooting, so pulled over, shut off motor, only to find out it wouldn’t start back up. I freaked out, this is a 2013 Freightliner M2-106 automatic transmission, your video show exactly where to look for the fuse. Changed it, and it started right up, now however there is a check engine light and diAG 1 on dash. Now at the very least the motor is running, huge plus, and I have you to thank for that…If you hadn’t posted this, I would be still sitting here no motor running, draining power, hating life (just joking) thank you…you rock!
@@diesel-landdiagnostic7407Amigo I have a question...im having problems with the same type of truck ....water separator keeps going empty and left high beams are inop...any help is appreciated. Thanks
Thank you so much! I don’t know if this is the issue on my truck, yet. I wish I would have seen this video before taking it to the shop. I’m new at this and I’m clueless at this point
Bought it at an auction installed timming sensors checked fuses acts like no fuel installed inline fuel pump now it tries to start with a little either but won’t so I bought a new fuel pump to install on heui pump haven’t yet but cranks great just won’t start
The M2 Freightliners are notorious for moisture in the fuse compartment. Get some Dielectric grease (use sparingly) on a qtip clean the fuse on the both sides of the individual fuse holders. It will work wonders...that F7 fuse in particular. We have 2 2018s M2s and replaced both the fuse boxes on the trucks. If you replace the box make sure to clean all the pins on the make conector(s) going into the box. Its pretty easy to change the box.
Thanks for sharing. Good to know. I have M2 106 tow truck and the AC is not working. I done everything found out that I don’t get power to compressor !! I ran temp +wire to battery and to switch inside. Where is the fuse for AC or Compressor ? What do I do? Thanks
I have a 2015 freightliner m2 won't star I replace the starter motor I thought that was gonna solve the issue but still won't start even I try to direct power to the starter and nothing can you give me any idea what could be the problem please
Hey My transmission keeps going into a 1F state not allowing my to change gears automatically and not allowing me even to go into reverse or back into neutral? Any ideas of what it could be?
I have a 2011 M2 with the factory battery shutoff switch. I put two new batts in it, and had no power, so I replaced the shutoff switch, and still don't have power. Is there a fuse for that switch, since it's on the positive side?
I have a 2008 freightliner M2 and it’s working good I driving probably 400 miles and I Las signal gauges and I open the hood and I see I don’t have diesel and somebody come and try to put the scanner tools and he say is no Lego in an a computer I check the fuses in every single fuse it’s OK so I don’t know why Northstar is cranking only not running I check the diesel passion and there’s a lot of diesel only not raining
There’s many reasons why it won’t start. Damaged high pressure pump, injector rail o rings, camshaft sensor, battery fuses, shortage, even damaged IDM Which is right next to the ECM. What are the symptoms or story?
@@diesel-landdiagnostic7407 Sorry, kind of vague. Truck started, ran and warmed up while I checked air in tires on truck and trailer. Shut down as normal. Two day's later, dash lights on switches blinking, no air buildup for parking brake. No crank, nothing. Checked V in batteries, both 13 plus. Cleaned all connections on battery cables and ground connection at frame. Checked voltage at point of connections at firewall where cab grounds, and 12v connections are. 5.4v ! Also checked fuses at battery and firewall. Now, turn key on and there is nothing, except once in a while there is a noise behind the fuse box on the dash. And no dome lights anymore. If I hook a trickle charger to the point at the firewall I then get some dash switch lights flash as well as the auto trans selector indicator flashs. No crank. The speedometer sometimes clicks like a second hand and if I leave the batteries hooked up it will click until it buries itself.
![Noob To Max With DRAGON REWORK In Blox Fruits [FULL MOVIE]](http://i.ytimg.com/vi/LnBMOinoOvA/mqdefault.jpg)
Dude, been stranded in Warmington Delaware for an hour now when I found this video. Code was “no trAn” “EnG 0” “bH 33” “diAG 3”
I had pulled away from a light with no power, no speedometer, figured ECM might need rebooting, so pulled over, shut off motor, only to find out it wouldn’t start back up. I freaked out, this is a 2013 Freightliner M2-106 automatic transmission, your video show exactly where to look for the fuse. Changed it, and it started right up, now however there is a check engine light and diAG 1 on dash. Now at the very least the motor is running, huge plus, and I have you to thank for that…If you hadn’t posted this, I would be still sitting here no motor running, draining power, hating life (just joking) thank you…you rock!
Similar situation right now with no error codes getting power but won't turn over. Sol
Want to say thank you for this video. It helped us start the truck and get it moving
I’m glad my videos are helpful.
That was amazing dude ty.
My friend, you saved my life. ❤
Just here to help! 🙏🏽
@@diesel-landdiagnostic7407Amigo I have a question...im having problems with the same type of truck ....water separator keeps going empty and left high beams are inop...any help is appreciated. Thanks
Awesome stuff mate big thumbs up keep them videos coming
Bro thanks bro your very helpful that actually help a d turn my truck on
Thank you so much! I don’t know if this is the issue on my truck, yet. I wish I would have seen this video before taking it to the shop. I’m new at this and I’m clueless at this point
What was the issue?
Thank you for this, you really saved me lot of money,
Yep that’s pretty damn cool, power probe helps a lot, 👌👋👍👍
Thank you so much bro, I fixed the same problem!
I had the same issue . I just replaced the 30 amp fuse and it fired right up after being down four days plus almost getting
Towed
Gracias Omar.
I love you bro! Thank you !
Thanks man. Helped me out alot
Thanks brother
awesome video thank you
I have the same problem, I had to do an overlay from F7 to pin 63 of the TCU ( Allison transmission)
Bought it at an auction installed timming sensors checked fuses acts like no fuel installed inline fuel pump now it tries to start with a little either but won’t so I bought a new fuel pump to install on heui pump haven’t yet but cranks great just won’t start
Thank you so much, where are you located?
Hey thank you so much
What is the main problem with these freightliners box trucks? Are they good to buy or do they have a bunch of mechanical issues thanks great video.
On a 2019 Kenworth t680 what fuse number will that be?
What about crank but no start on the same type of truck have u had this problem before
I need to locate the fuse to the clearance lights of my m2 please
Thank you brother
Buen día amigo qué tal como pudiera comunicarme con usted para una consulta gracias tengo un problema similar a este que tenga buen día bendiciones
I have that same problem but I have power on both sides of that fuse. I was hoping you found something different. Damn.
What about if that portion of the fuse box where that one fuse was has no power at all? That’s what I’m dealing with now on an m2
Hi, I'm experiencing something like this but, I have a 10 speed and the transmission will not light up or go in gear...
Great video bro
What causes this and is it a common problem
2006 freightliner m2
FMI2 Data erratic. intermittent or incorrect? what does this mean?
I need one of those Fuse boxes ECU PDM you’re working on mine went out do you know where I can buy one used a refurbished
Thanks
The M2 Freightliners are notorious for moisture in the fuse compartment. Get some Dielectric grease (use sparingly) on a qtip clean the fuse on the both sides of the individual fuse holders. It will work wonders...that F7 fuse in particular. We have 2 2018s M2s and replaced both the fuse boxes on the trucks. If you replace the box make sure to clean all the pins on the make conector(s) going into the box. Its pretty easy to change the box.
Thanks for sharing. Good to know. I have M2 106 tow truck and the AC is not working. I done everything found out that I don’t get power to compressor !! I ran temp +wire to battery and to switch inside. Where is the fuse for AC or Compressor ? What do I do? Thanks
Damaged wire by or plug from the fuse box. Really common on this m2.
Gracias!
Do you know what code 1569 engine protection torque derate means
My truck won’t crank… no lights on the dash or anything. Any suggestions?
Truck won’t start or won’t crank two different things.
Year, Make, and Model
Hi .. I have 2012 m2 the truck shut off on the road I go there I Don have power on dashboard not star can help me out
Great. I used
Thanks you.
I have a 2015 freightliner m2 won't star I replace the starter motor I thought that was gonna solve the issue but still won't start even I try to direct power to the starter and nothing can you give me any idea what could be the problem please
Good mornings I got the same truck where is located the fuse for the cigarette lighter fuse my truck is 2018 help please God bless you
I have a question: I been working on 22 M2 and when the truck pass a bump it dies, but start right up again
And your question is?
Dealer made me purchase a new TCM when this happened to me before smh
I’m glad you got it running 👍🏽
Hey My transmission keeps going into a 1F state not allowing my to change gears automatically and not allowing me even to go into reverse or back into neutral? Any ideas of what it could be?
I have a 2011 M2 with the factory battery shutoff switch. I put two new batts in it, and had no power, so I replaced the shutoff switch, and still don't have power. Is there a fuse for that switch, since it's on the positive side?
Were you able to fix it?
I have frighliner m2 2010 it’s cranking but not starting all fuses are in good shape what it can be the problem
Lots of thing
High pressure fuel pump
Injectors
Fuel pressure problem
If we somebody can help me to figure out what’s the problem
I have a 2008 freightliner M2 and it’s working good I driving probably 400 miles and I Las signal gauges and I open the hood and I see I don’t have diesel and somebody come and try to put the scanner tools and he say is no Lego in an a computer I check the fuses in every single fuse it’s OK so I don’t know why Northstar is cranking only not running I check the diesel passion and there’s a lot of diesel only not raining
Finally figured out why my m2 shows no trans on first start up, then I shut it down, and it finds trans lol
I’m have same problem with 2012 peterbuilt220
I have a 2007 with a cat 7 cranks won’t start why
It could literally be so many things
Blown fuse
Timing sensor
HEUI pump
Injectors
What’s the back story?
Where are you located I have a 2012 international I have couple questions regarding a regeneration problem
Commerce CA
Damn if only I found this when I got called to do a jumpstart. I could’ve earned $200 instead of just doing. $80 service charge
I have the same problem on dd13
I have a 2007 Freightliner M2 and getting code BH 164 my cigarette lighter, my high beams and courtesy lights don’t turn on
You're going to have a short.
I have spn 6966 code and number 15 fuse keeps on popping ever time I change it anyone have a idea what could be the problem?
Awesome info buddy but I keep blowing the F5 ignition fuse and cannot find out why? any experience with this?
@G.I.M Transport LLC thanks
You have a short.
But why is the fuse blowing out?
If its blowing out there might be a short
EXELENT SON
Thank you Sir!!!
Code 225 primary clutch pressure
Hi Film it horizontal..and show the wiring diagram..
Screen gets smaller. Sorry filming with my phone..
And was the mcm
I have a 2015 Freightliner cascades dd15 13 speed, and I have a no trans on my dash but my truck still runs. Any idea what’s causing the code?
If you have a code I might be able to help.
2009 International 4400 no start
There’s many reasons why it won’t start.
Damaged high pressure pump, injector rail o rings, camshaft sensor, battery fuses, shortage, even damaged IDM Which is right next to the ECM. What are the symptoms or story?
@@diesel-landdiagnostic7407 Sorry, kind of vague. Truck started, ran and warmed up while I checked air in tires on truck and trailer.
Shut down as normal.
Two day's later, dash lights on switches blinking, no air buildup for parking brake. No crank, nothing. Checked V in batteries, both 13 plus. Cleaned all connections on battery cables and ground connection at frame. Checked voltage at point of connections at firewall where cab grounds, and 12v connections are. 5.4v !
Also checked fuses at battery and firewall.
Now, turn key on and there is nothing, except once in a while there is a noise behind the fuse box on the dash. And no dome lights anymore.
If I hook a trickle charger to the point at the firewall I then get some dash switch lights flash as well as the auto trans selector indicator flashs. No crank.
The speedometer sometimes clicks like a second hand and if I leave the batteries hooked up it will click until it buries itself.
@@stevedunlap9786 what Engine?
9.3L Dura Star max force 9
@@stevedunlap9786 have you hooked up Servicemaxx?
I am having code 1894
Hello hello