Installing a OEM switch in your Tacoma (Light bars, winches, pods, rock lights)
HTML-код
- Опубликовано: 4 авг 2024
- In this video I show you guys in detail how I wired in an OEM switch to control my rock lights. You can use them to control light bars, rock lights, pods, winches, anything on your Tacoma!
Switches
-Square amzn.to/3ocIuZa
-Rectangle amzn.to/387u86K
Tools used in this install
-Wire stripers amzn.to/3hEiLXq
-Screw driver (drill) amzn.to/3hFrhW6
-Socket Set (10mm) amzn.to/3rMVrv8
-Heat shrink amzn.to/3hFrubQ
-solder iron amzn.to/3oborud
-solder amzn.to/2X6CwgO
-lighter (to melt heat shrink) amzn.to/3n7WzGe
💡MODS so far on the 2020
- Rough Country Lift Kit w/ Lifted Struts and N3 Shock in Rear www.roughcountry.com/toyota-s...
- Tri-Fold Gator Tonneau cover amzn.to/3bpvglB
- LED Interior bulbs amzn.to/2M4yyO1
- LED License Plate bulbs amzn.to/2M4yyO1
- Plasti dip amzn.to/2XA4NMD
- K&N Cold Air Intake amzn.to/2ZS7I5C
- K&N Recharge Kit amzn.to/3htcxZ6
- Tailgate Letters amzn.to/2WU9gdP
- Diode Dynamics Stealth Light Bar Kit 2016-2020 Tacoma's www.diodedynamics.com/2016-20...
- OEM Light Bar switch amzn.to/2BXWpiY
- Diode Dynamics DLR RGB Upgrade KIT - www.diodedynamics.com/multico...
- Diode Dynamics Halo KIT - www.diodedynamics.com/hd-led-...
- Diode Dynamics Headlights www.diodedynamics.com/led-bul...
- TRD Pro Grill toyotaproshop.store/products/...
- Depo Tail Lights amzn.to/2MCsIWr
- Tekonsha P3 amzn.to/3fQ7UqU
- Back up Lights: amzn.to/33Ts6UL
- 2016 to 2019 lights Bed Lights amzn.to/2Xbgf3z
- Raptor Lights amzn.to/38cRzMA
0:00 Intro
0:21 Why use a OEM Switch
1:53 What you need
3:53 Install
8:21 Wiring
10:04 Put it back together
12:10 Finished Product
12:50 Outro
📲 SOCIAL MEDIA
Instagram: / djrickweb
Facebook: / djrickweb
Mixcloud: www.mixcloud.com/ricky-weber/
Twitter: / djrickweb
📸VIDEO GEAR
-Cannon G7x mark 3 amzn.to/3aRKIqp
-GoPro Hero Plus amzn.to/2iO0RER
-DJI Phantom 3 amzn.to/2iGFlOJ
-Joby GorillaPod amzn.to/2jvlbM6
-Seagate 2tb Hardrive amzn.to/2tr6wTb
-Sasmung T3 hardrive amzn.to/2tWVKpM
-Edit Software: Cyberlink Powerdirector 14 on Windows
BIO
I was born August of 1995 in Ohio. I now live in North Carolina. I am a mechanical engineering for a tire company and I have been a professional open-format club / mobile DJ since 2012. I created this RUclips channel for the purpose of sharing my experiences and knowledge as I tinker and mod my 2020 Toyota Tacoma TRD Off Road. If you have any questions don't hesitate to ask. 
Авто/Мото
![Gunna - one of wun [Official Video]](http://i.ytimg.com/vi/w_JtBYqMgk8/mqdefault.jpg)
Best video on putting in an OEM switch that I have found. Hooking it all up without the extra wire then testing it is key.. then the extra wire is the top symbol. sweet ! All the other ones i watched had them all hooked up and some crossed the wires. You got it right and filmed it right. Thanks man ! I'm doing this in the next few days. Just waiting on some wire loom :- )
All your videos are very informational and easy to learn from,keep up the great work
Good video. Helped me on figuring out the connections between the new switch wiring harness and the leads for the Rocklights.
I’d love to see you do a CB radio install. You’re videos have been so helpful with all the mods. Thanks!
Good videos bro you get straight to the point ad very helpful 👍🏻
Great video. I am saving for the down payment on a 2021 or 2022 Tacoma TRD Off-Road. I live in a state that Light Bars are 100% Needed for Winter.
Big Taco Rick!! I appreciate you showing me how to take apart the panels.
Awesome video. Gonna install my mictuning rock lights soon. Yes I'm gonna replace that switch with the mictuning switch.....!!
Nice informative tutorial. Best I have seen. Thanks for the help
I tried to get an OEM switch for my air compressor to place where the ECT power goes (6mt) and accidentally bought the long style instead of the smaller style. Where your light bar switch is, I have a clutch start cancel switch. Up top for me is a coin slot that I’m going to remove. For some reason I thought I could just remove that upper portion of dash by pulling. Thank you for saving me from breaking stuff 😂 didn’t realize there were bolts at the bottom
Been doing a lot of research on installing aftermarket fog lights. It turns out if you're not running the power to the lights through a relay you're running the risk of wiring to the switch
overheating and possibly causing a fire.
Good video, now I need to figure out what I want to use a switch for hehe👍🏼
Best video I’ve seen yet
Great video & explanation. Thanks
Very informative. Nice truck.
Tremendous installation. Where can I get the switch at the bottom horizontally to turn lights on and off. thanks for your help
Just curious to if the 3rd gen switches would fit in a 2nd gen because I’m wanting the ones that look like the factory ones but can’t seem to find one like the 3rd gen switches?
I just put one in my truck, same company and it doesn't fit flush. Did you trim your accessory switch pannel to fit it
I don't know if you have to go through the process of taking the dash off like you did. But you can also just pop out that little panel with a flat head screwdriver, then pop it back into place once you're finished.
There is no need to do 90% of the work he does on this video to install that button
I just did a light bar install. No need to remove the lower dash. Just pop out the panel with the switches.
Thanks
The palm spring critics of your vid need to spend their precious knowledge w a time consuming vid of their own
Thanks again
You R the only one in a dozen how tos to show and tell clearly the connection rewire between supplied harness 3 wire and push switch 4 wire
That in itself is worth cali cool raised and ch4x4 to pay you
Yes this guy is clueless on doing this kind of work
Great video! Any ideas for this situation? I hate the parking backup and blind spot monitor switches on my Highlander 2016. I don't know why they have these switches. Many times I have backed up and not realized that someone (car wash folks maybe) inadvertently turned off the parking switch. Luckily I did not back up too far. Same for blind spot monitor. Point being I would like to remove the ability for these two switches to be turned off and just have them permanently in the On position. Any ideas? I guess I could remove panel and wire them in the back to be on making the switch inoperable. Or I could turn them on and leave them in the back of the panel and replace their spot with a blank. Guess these switches cannot be popped out of the front without removing the panel right? Thanks for any ideas and thanks for video
Yeah depends how the switch is wired but should be able to do so. And unfortunately yes you will have to take the dash off
Good video. Like your name too!
That panel with the switches pops right off with a plastic tool. I did the same job by just popping it off.
That’s what I want to know is the other red wire for the dash light where do I connect the other red wire?
A lot of vids tell you to take apart your dash just like this. There's a way simpler way. Just use a butter knife or soft edge body tool and work your switch blank out working slowly top to bottom and back. Then just pop in your switch and connect.
Great video! How did you tie into the dash board light circuit that turns on the light for the switch when you interior lights come on? Did you tie into one of the main switches?
The green wire going to all the other switches is for dash lighting. I just tapped into the near by switches wire
@@TacoRick Hey Rick. How did you know which wire to tap into for the parking lights or running lights?
Yes, can u let us know which wire to tap from the near oem switch to power acc.?
How do you know what power wire to tap into for switch backlight when off?
Voltage tester.
Another good video, sucks that amazon got rid of the Zombie Lights button
My 8 light C2 RGBW LED rock lights kit came with blue, brown,yellow/green strip would you happen to have any clue what colors go to what cor on OEM switch ?
No i dont
Quick question, do the lights only turn on with acc and the key or will they turn on with the vehicle off using those switches?
Since it's wired to the battery you can turn them on with the vehicle on or off at any time
Great video man. Could you clarify which wire I need to tap off of in the bundle to get the backlight to work on the switch?
Can't remember. I used a volt meter and turned the dash lights on and off to find it
This is the only thing I came here for and didn’t get clarification lol
@@afallenbaumme too 🤷♀️
You just plug it into power? Won’t that kill your battery if you forget it on?
@3:11 what do you tow? What’s the weight? I’m thinking about adding one too. Thanks
12 by 6 enclosed trailer. Not sure weight but its steel and heavy duty gauge
Sup man. How do you keep her clean during the winter? Same process as the warmer months?
I use touch less washes in between bigger washes. In the winter I mostly do touchkess unless I get a warm day that u am free to clean it
Hey brother I have a question. I have a '14 Tacoma Access Cab. On my light panel I have the upper panel of 3 switches closest to the vent. On the left is the factory switch for the vehicle fog lamps. The middle one, which I just replaced and it was a "true" blank and put in the switch for my ditch lights. The third and last switch blank isn't really a blank. When I pulled it out it had connector on the back with a bunch of wires running out from it. Do you have any idea what this does? I'm asking because I'm putting more lights on the truck and I really don't want to have to drill into my dashboard. Can you or anyone on here provide any insight? Thanks in advance.
Could be pre-wired for the feature that a switch going there would do. In that case the wires are not being used. But no clue
How get LED switch?
I dont understand why the light bar icon on my switch will not turn off, even after the light bar is off, along with everything else on the car. Its pretty upsetting that I went through all this work to not have the button work right. Please help
Which wire do you tap into for the dash lights?
That’s what I’m wondering too? He dint show it
You can pull that side panel out directly with a plastic pry tool. it clips in. Also good luck with your future cab fire lol. USE RELAYS.
Where did you get the power going to the green wire?
The power wire comes direct from the battery.
My oem switch said that it has to be operated through an installed relay or else it would melt but every video I see using the same cheapo oem switches are directly connecting them to the light power and ground wires. Have you or anyone else you know had any issues doing it how you did?
No issues 2 years running
Hey taco rick! Where did you get your zombie light OEM switch from??
Amazon
How did you figure out which wire goes to the dash light?
Wondering the same thing
I got my button all hooked up and it works to turn my ditch lights on but the button itself doesn’t glow
Have to hook that other red wire into the power from the other dash lights.
The red wire for the dash light, where did you connect it to??
Any green wire running to the other switches.
Thanks Man🤙🏼
How did you get your Rock light switch inside ?
See the rock light install video. Went through a grommet in the fire wall behind the dash. Pretty easy to get to.
What about the center console under the ac knobs?
Can you make a video on phone mounts?
Check my top Amazon purchases. Its in that list.
So what did the extra red wire go to?
The one by the green wire is the output power for the device. The other red is the dash light. Not necessary if you don't want it. I tie it into the dash light wiring.
Hey man . I install mine today same as your OEM switch but it keeps on even if my truck is not running . Iam afraid if its gonna drain my battery. Looking forward for your opinion ✌🏻🤙🏻
The switch works even if the truck is off but if the switch is off no power should be going anywhere.
@@TacoRick switch works great . My concern is the blue back light is still on even if my truck is not running . Now my question is ,is it gonna drain my battery ?🤷🏼♂️
It should not be on? Mine is only on if the dash lights are on or of course if the switch is on.
@@TacoRick First; thank you for all your videos, very helpful. Second; I installed the OEM switch as you did and the blue backlight stays on. Vehicle shut off, blue back light on. What are your thoughts?
@@ericpless3058 I've got the same problem but I'm using a tap in fuse I can't figure out what I did wrong
The rocker switch stays on all the time. Why?
Bro I just installed the switch and a blue light from the little truck it's on all the time?
Depends how you wired it. Sounds like you hooked it up to a constant power source instead of the dash lights power input
You can just popped out the panel where the switches are without disassembling half car
I followed this and now my rock lights not turning on
I want oem switch…
Gets zombie light switch 💀
Nb
Great video! However, removing the entire lower dash to get to the switch panel is unnecessary. This video will show you how to pry out the switch panel- ruclips.net/video/i5un69_YhPw/видео.html
Too bad you glossed over the dash light connection, that's the step that everyone else on the yootoobs seems to skip, too.
Jank
Works great
The rock light you installed look tacky af.
How?