Delboy's Garage, Removing Stuck Brake Caliper Pins

Поделиться
HTML-код
  • Опубликовано: 21 авг 2024
  • A little 'Rescue How-To' for stuck caliper pins..!
    www.patreon.co...
    Delboy's Garage is part funded and supported by Patrons who keep us on the road.. from just $1 a month you can join the fun by clicking the link above.!
    Music today by "w0ffle" (thanks buddy)
    Keep up with the latest on Facebook:-
    / delboysgarage
    Follow us on Twitter:-
    / delboysgarage

Комментарии • 316

  • @kjelldavidlindquist
    @kjelldavidlindquist 7 лет назад +23

    Something I always try is to take a torx bit, cant be the cheapest one, of appropiate size and hammer it in with appropiate force. Many times this works because the hammering loosens the bolt, and the torx bit cuts into it, making it's own grooves and then you can turn it.

  • @scottmurray5600
    @scottmurray5600 4 года назад +1

    Brilliant video. I've got a Triumph Tiger Explorer. Tomorrow I'm copper slipping those bolts before I get this problem. BRILLIANT VIDEO.

  • @terrycolley6482
    @terrycolley6482 Год назад +2

    Good video. I especially like that you advised to disconnect the battery to protect the ECU. This really is the avenue of last resort where the pins seize and the hex has been rounded out. May I share something I've learnt with these pins over the years. If the hex is still good don't just grab the first allen key in your toolbox and start heaving on it risking rounding it out. If your garage is like mine you'll have gathered more than a few 5 or 6mm allen keys. The size variation between them can be considerable especially with cheap Chinese made toolsets. Get your digital caliper out and measure each allen key. Find the biggest of the bunch, it''l be much tighter in the hex and you'll have a much better chance of it breaking the pin free. Another little tip - before heaving on it to undo it, go the other way, yes, to tighten it. Sometimes it's all it needs to crack it free a little. Oh and spray some penetrating fluid on it a couple of hours before starting. Not WD40, a proper penetrant such as Plus Gas or Penetrene or your own mix of acetone and ATF a combo that many car and motorcycle restorers swear by.

  • @syedbasitalishah5576
    @syedbasitalishah5576 8 лет назад +4

    Thanks Del! You are one of the best technical teachers i've had! Learned from you a lot! Cheers!

    • @Moonfleet41
      @Moonfleet41  8 лет назад +1

      You're most welcome Syed, thank you for subscribing , keep in touch, always happy to help !

  • @batoutofengland3574
    @batoutofengland3574 8 лет назад

    Yes the fun stuff . My boy learned how to clean the bikes chain yesterday after watching you video , so then we went out side and went through the steps and cleaned the chain together . It helped him to see how to do it and why from Del then working on it him self . thanks mate

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Thanks buddy, thats so kind, it makes me really proud and honoured to be able to inspire the next generation... tell him i said Hi, take care guys.. Del.

  • @hedgehog3900
    @hedgehog3900 7 лет назад +1

    Last september i had this at MOT time on my trusty vfr.Tried drilling and easy-outing.Massive failure.£45 e-bay caliper sorted it eventually.
    I wish i had a welder handy then though i must admit this never occured to me.
    Great stuff as ever,thanks muchly :)

  • @charleshall5576
    @charleshall5576 8 лет назад +8

    Another option is to use a torx bit that is just a size larger, tap it in until it full seats then use a impact driver to remove it. I've done a few nearly rounded out allen bolts that way.

    • @Moonfleet41
      @Moonfleet41  8 лет назад +1

      That works really well for a single 'Break' free situation where a socket cap bolt is simply done up tight....but these pins are not holding on via the thread... its the shaft of the pin thats corroded into the old dead pads.... and in these situations, even a hammered in Torx bit will eventually round out the bolt... but what ever works aye.. lol.

  • @richardkelso9478
    @richardkelso9478 4 года назад

    I am having this problem with a front pin. Thanks for this, very helpful. Also was very happy to see a license plate on your wall from my hometown of Cheyenne, Wyoming. Great channel.

    • @Moonfleet41
      @Moonfleet41  4 года назад

      Glad it helped you Richard, and thank you for your support.. !

  • @clintselby5035
    @clintselby5035 6 месяцев назад

    Thank you for this advice. I’m going to remove the pins from my calipers now, straight away, while they are fairly new, and apply anti-seize as a preventative.

  • @rcchurchy4417
    @rcchurchy4417 8 лет назад

    I've had this issue a few times as I have a few older bikes, latest one was on my 900rr on the front calliper. Used an old torx bit and a hammer, have stainless in now much better than the cheap ones that were in there! I keep a small supply of torx and spline bits just for moments like this. Never thought about welding it, will be something to think about next time! Keep em coming Del!

    • @Moonfleet41
      @Moonfleet41  8 лет назад +1

      Cheers mate, the torx bit method is always a good favourite !

  • @joshjensen6239
    @joshjensen6239 8 лет назад

    This video gives me a great appreciation for Brembo calipers; I have them on all my bikes now. Those caliper pins are friction fit and bang easily in and out with a hammer. no threads no seizing :)

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Yeah, Brembo do some thinking aye, calipers built to be maintained, these clunky ols Triumph ones are from the arc, they were using this design in the 1980's... you'd have thought they would have moved on by now aye?!

    • @joshjensen6239
      @joshjensen6239 8 лет назад

      just goes to show where budget cuts for R&D are. I like what I am seeing with motorcycle manufacturers on modern bikes just outsourcing this stuff to companies that specialize in it, like Brembo, Nissin, etc.

  • @ricks.1318
    @ricks.1318 8 лет назад +1

    "Thanks" Del ..... Another GREAT VIDEO Sir !! You are a DAMN GOOD instructor ....

    • @Moonfleet41
      @Moonfleet41  8 лет назад +1

      Wow, thank you very much - we try our best !

  • @paulmessenger1006
    @paulmessenger1006 8 лет назад +3

    I made up Allen key fitting out of old 6 mm with 3/8 or 1/2 drive when they were worn out. I grind the hex to about 5.1mm perfect fit and never get a problem. Even new pin and Allen key is a sloppy fit, then 1st time you really swing on them they ream out. Got some ever so slightly bigger ones too when my mates have messed their's up

  • @RenchRanch
    @RenchRanch 8 лет назад

    Great vid! I have found that the anti-rattle clips in the caliper act as springs to put a side load on the caliper pins as they push the pads against the pins. This acts "like" a split washer to some degree. So I totally agree, you don't need thread locker or to lean on it. Just snug the caliper pins up and it's fine. And the copper slip / never-seize is worth the effort. It will make life much easier later. Cheers!
    Mike

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Ayup buddy, hope you are both ok your end ... counting the days !

  • @michaeldooley654
    @michaeldooley654 6 лет назад

    I wish I'd found this video 3 weeks ago 🤣😂🤣 great as always. I've learnt my lesson now.

    • @Moonfleet41
      @Moonfleet41  6 лет назад

      Thanks buddy, glad it could help you for the future !

  • @springy-2112
    @springy-2112 8 лет назад

    a good save!!
    i had this on rottweiller but no welder so i took the caliper off ground off the pads (was fitting new ones) heated the pin and mole gripped it...luckily it worked...bloomin triumph rear calipers !!!
    cheers budsky..
    (thought i would go budsky , had a band member once who said it all the time i really wanted to poke him in the orbit , i sacked him instead!!)

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Ha ha... Orbit AND THEN sack... even better..! Cheers me dear, Oh and early model Kawasaki GPz's used the same lame caliper too... ! says it all aye.lol

  • @timbarnett3898
    @timbarnett3898 5 лет назад +1

    OK , I've watched an seen the weld! Your points just soared, haha! Tim.

  • @shannonmacdonald1440
    @shannonmacdonald1440 5 лет назад

    Great tutorial Del. This is how I met you by the way...searching on RUclips because my caliper pin was seized. A while before this video unfortunately. Tried just about everything, never thought of a welder. Too much Monkey Boy ingenuity and I ended up buying a new caliper. Would have paid for half a new welder. Keep up the great work. I love watching.

    • @Moonfleet41
      @Moonfleet41  5 лет назад +1

      Hey Shannon, Thank you for you lovely message, and for sticking with us all this time... we really appreciate the kind support.. we all learn as we go along aye.. as long as a thing done wrong teaches us how to do it right.. then it still has value wouldn't you say..!!

  • @gsh319
    @gsh319 6 лет назад

    Having had this problem before, I've had good luck with grinding a sharp graduated tapper into a sized up hex "allen" socket then rapping it in with a hammer. Trimming off the tip to get the perfect depth of the modified socket is the key here. I save all my bitched up tools in a separate drawer. These tools are my secret stash for emergency mods! I do like your method more, more skill and who doesn't want to light off the welder to fix a problem. Thanks for your great lessons

    • @Moonfleet41
      @Moonfleet41  6 лет назад

      Thank you Scott, I really like that solution, and I'm gonna use it... can't always use the welder with the heat involved, and yeah I have a drawer full of cannablised tools, it's my 'get out of jail free' drawer !

  • @rossjob8564
    @rossjob8564 4 месяца назад

    I have this exact problem I'm going to give it a go with my wilder thank you for making this video you are so much help

    • @Moonfleet41
      @Moonfleet41  4 месяца назад

      Glad it helped, good luck with it.

  • @PaulR387
    @PaulR387 Год назад

    Great stuff Delboy, another brilliant video..

    • @Moonfleet41
      @Moonfleet41  Год назад

      Thanks mate. Glad you enjoyed it.

  • @philcore1336
    @philcore1336 8 лет назад +1

    I have always wandered if that method would work, i'm glad it did. Great vid!

  • @gearjammer3688
    @gearjammer3688 8 лет назад +6

    I would have been dancing round the garage after getting the pin out.

    • @Moonfleet41
      @Moonfleet41  8 лет назад +5

      I edited that out mate lol along with the running man dance!

  • @DMoots
    @DMoots 6 лет назад +1

    Lots of wisdom in this video. Very good!

  • @roamingdev4990
    @roamingdev4990 8 лет назад

    Great to see you getting back to "helpful tips" type videos Del. I've missed your tutorials.

    • @Moonfleet41
      @Moonfleet41  8 лет назад +1

      Thanks buddy, we do them as they come along ! We have a lot of different directions now, simple skills, ride videos, and the project, all in the aim of keeping everyone entertained with something different ... cheers, Del

  • @TheChipmunk2008
    @TheChipmunk2008 8 лет назад

    Del, know I'm always commenting but... these tips can be so useful to even someone who isn't a biker, it's like you said about 'mechanic'... use common sense, deduction, and (something you didn't say)...modify tips like this you've picked up from elsewhere, and make em work!
    Cheers

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Thanks mate, just trying to buck against the trend of us all becoming paying customers, when we should be doers and fixers! None of what we produce in video is ever that taxing, most of it just common sense maintenance... and who can't do that with a little bit of thought ?!

  • @johnstrothard
    @johnstrothard 7 лет назад

    Another great video, but no welder here, and I won't waste my time with JB Weld. I got my pin out with an EZ Out, or screw extractor. I used the biggest one possible, was able to drill down 11mm and got really good purchase. A little patience, and the job was done. Thanks Del and Penny!

    • @Moonfleet41
      @Moonfleet41  6 лет назад

      Nice one John, always love to hear of great little ways to get round this sort of thing... you can also have success , if it happens again, by hammering an over-sized torx bit in to the end, I did that with this and it didn't work, so I had to resort to the welder, but hey, we do whatever works aye!

  • @gilaraujo
    @gilaraujo 8 лет назад

    Very very good tip that i am sure could be used in many other situations. Would have never thought of that in a million years! Thank you!
    Great info on the battery and welding mess! wouldn't think of that either!

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Thanks Gil, its a very expensive mistake, and aweful to find out the hard way..

  • @roadsonboard
    @roadsonboard 8 лет назад

    Thank you for another great tip and video Del. Nice to know if one is ever in a mess, chances are the fix will be on your channel no doubt. God bless you fella!

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Thanks buddy, there's always around something aye?!

  • @springy-2112
    @springy-2112 3 года назад

    Hang on , this is a repeat ! I'm sure I saw this 4 years ago ! 😊.. ha..
    Hey brother it just came up in suggestions so I thought I would have a nostalgia trip ... lovely jubbly 👍🏻☮❤

    • @Moonfleet41
      @Moonfleet41  3 года назад +1

      Blimey, doing the rounds again aye brother, well it's all good for refresher if nothing else, it's either that or the YT gods know there's a cold winter coming!!

  • @syrioforel2125
    @syrioforel2125 3 года назад +1

    OK, so I got stuck brake pins and the hex key was almost able to spin in the sockets. First thing I tried was to use an expensive Park Tool hex key, but that didn't work out.
    This is a success story - hope it will help some desperate soul ;)
    First I used lots and lots of WD40 over the span of a few days, then an impact driver (the one you use with a hammer, not the battery-powered one) which didn't seem to do anything.
    The last thing was to use a breaker bar together with the hex bit from the impact driver set - those bits are made of hardened steel and I think are also a little bigger than regular ones.
    While pressing the tool hard against the socket of the pin, I turned the breaker bar veeeery slowly counterclockwise and - guess what: both the stuck pins popped and I was able to remove them and dance a celebratory morris dance knocking stuff off shelves in the garage :)))

  • @TroubadourJuggernaut
    @TroubadourJuggernaut 8 лет назад

    loved how you did that in real time, maybe it will work, maybe it won't .... you took the chance and of course did it perfectly

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Thanks mate, well, no job is guaranteed till it's finished, and it's arrogant to think it will go right no matter what ... as so often, they don't!

  • @skullbugerie
    @skullbugerie 8 лет назад

    such a nice feeling when u have a victory over a mechanical issue isnt it

  • @christophermallard8657
    @christophermallard8657 4 года назад

    Thanks for your advice. In the end I got my pad pin pub grub screw out with a good right fitting screwdriver which had a hex on the grip. Ring spanner over the shaft to fit the hex so I could push hard with the screwdriver and turn with the spanner. Sorted thanks again.

    • @Moonfleet41
      @Moonfleet41  4 года назад

      Great news Chris, thats the result we like... when you fit it back in, now you know it only needs nipping up gently..

  • @stevelampard
    @stevelampard 8 лет назад

    Just a little tip with the welding, try and keep the feed lead as straight as possible. This will help eliminate spattering and promote a consistent weld, even if you're just tacking.

  • @kennynvake4hve584
    @kennynvake4hve584 5 лет назад

    You could cut the bolt head with a die grinder, to make a slot like a flat head screwdriver, then try to turn it. It will not hurt the caliper if you cut a SMALL, grove in the caliper, while cutting the bolt head, at a very small amount.

  • @LinuxGalore
    @LinuxGalore 8 лет назад

    I saw a motor mechanic with the same problem and he just hammered it out with a hardened screw drive. The method he used was to hammer a V in one side of the head of the alan key top then swap to a blunt screw driver and hammer that in the direction to loosen it. I saw him remove 4 stuck recessed alan key heads in about 3 min.

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Good man, all too many of them in the main dealers will just fit a new caliper and charge YOU for it...

  • @batoutofengland3574
    @batoutofengland3574 8 лет назад

    my lads sitting watching this video glued to the telly .

  • @stevenwatson3963
    @stevenwatson3963 8 лет назад

    Great tutorial Del.Nice one!These skills are redundant at the moment,because most companies earn more by selling you a new part,as opposed to selling the skills of an "engineer"who can sort your "broken stud","cross threaded sparkplug",siezed swinging arm,using "easy outs "blah blah blah. I left the trade in early 90s,because,most of the "older"guys were in my opinion,just jobsworths fitters,or technicians,as they liked to call themselves.Great video!.

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      A man after my own heart buddy, I had exactly the same experience... left the bike trade in 2006 for the same reasons... we employed a young lad of 21 with a degree in 'motorcycle technology' and yet watching weild a hacksaw was like watching a 4yr old playing with his 'my first tool set' ... honestly , clumsy wasn't the word, nice lad, but he couldn't think he way out of the toilet...! But you're right, he had the skills needed for modern motorcycle main dealerships, which is a shame ! Oh, I feel old sometimes lol ...

    • @stevenwatson3963
      @stevenwatson3963 8 лет назад

      On your point,my Vivaro van had a tyre blowout in about FEb/March this year,and so i took it to a local tyre fitter.I decided to watch as the young man proceeded to jack up my van under the sill,as it started to kink.I then said to the nice young man that you have not found the jacking point on a 2 tonne van,so i had to show him.I am glad i was there to police him.His certificate of competence was on the wall, as i paid 400 quid for 4 new tyres.All 4 hub bosses were corroded,no scratchbrush,and no coppergrease was used! Im a bit younger than you Del,but i SMH! Yo aint old Del,your knowledgable,and knowledge is power.ATB.

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      I've had exactly the same experience buddy... went to a local tyre fitter to fit some performance tyres to my Honda Civic, I watched a lad of no more than 18, who was apparantly a 'qualified tyre fitter' attempt to lever a bone dry tyre bead on to a new rim... he tore a chunk out of the rubber bead about 1/2" round, pulled it out with his fingers to look at it, it was still attached by a tiny thread, so he put it back in place, patted it in the hole it came from, then did a swift look left & right to see if anyone had seen him... whereupon he saw me watching! And then, believe it or not, he actually proceeded to wope some tyre grease over it right in front of me - I stopped him and called his boss out of the office, whereupon he argued he had greased it first and the damage was already there! As you can imagine, I went f*king mental! Took my rims and tyres and left, and worst of all, the manager actually got confrontational with me, never trust these people again!

  • @DrRockter5150
    @DrRockter5150 8 лет назад

    Love the camera-fall "Easter egg" at the end!

  • @shaun4164
    @shaun4164 8 лет назад

    i had the same problem with mine, i hammed a flat head screw driver bit in the hole and used a rachet on it worked a treat.

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Cool trick, can do the same with a torx bit as well!

  • @GarDee0
    @GarDee0 8 лет назад

    Lol was going to make a comment, but lol you got so many people out there who are telling you(suggesting) other ways to do it I'll just shut up and say nice work!

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      There's always another way to skin a cat mate, feel free by all means...

  • @jhstony
    @jhstony Месяц назад

    Thanks for this video, I am going to try this fix now 👍🏻

  • @petefroud5308
    @petefroud5308 8 лет назад

    Great advice Del . Dam steel in alloy is a real pain .You got a right result getting that out.

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Yeah, touch and go though... just as easy to snap the head off and find yourself surfing eBay for a new one..lol

    • @petefroud5308
      @petefroud5308 8 лет назад +1

      True Del . Welded a nut on a mower engine sump stud just would not move it .

  • @worzelgummidge3617
    @worzelgummidge3617 8 лет назад

    Another great video. I spotted you yesterday! coming out of Poole near McDonald's driving a coach :)

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Yeah, that would have been around lunchtime, blimey, can't hide anywhere lol !

    • @worzelgummidge3617
      @worzelgummidge3617 8 лет назад

      +Moonfleet41 hahaha

  • @ChrisDalvikBxl
    @ChrisDalvikBxl 8 лет назад

    Thanks for that one! I love these kind of videos, ride safe!

  • @baccas66
    @baccas66 8 лет назад +1

    Once again, sound advice from the guv'nor. Cheers fella.

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Cheers fellah, always good to hear form you.. Del .

    • @baccas66
      @baccas66 8 лет назад

      +Moonfleet41 It's that classic mix of steel and ally. Why do bike manufacturers love putting a steel bolt, usually allen or torx head and screw it into a blind hole. I'd much prefer a nut and bolt anytime.

  • @markpowell2657
    @markpowell2657 8 лет назад

    shagged bolts n studs....friggin nitemare....big up da weldage del lol👍

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Too right mate, if in doubt, melt it out !

  • @boombox469
    @boombox469 8 лет назад

    Wise words as always delboy. Love the tune at the end!

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Thanks buddy, that guy is an insanely talented guitarist aye!

  • @syedbasitalishah5576
    @syedbasitalishah5576 8 лет назад

    Liked it before watching. Subbed. Astonishing build Del! Cheers from Pakistan! Peace to all!

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Thanks so much Syed, and welcome aboard my friend. Ride safe there.. Del.

  • @ninjabortion
    @ninjabortion 8 лет назад

    You also might have decent luck if you pull the caliper off completely, pads and all, put it in a vice, then try backing it out by gripping on the unthreaded part of the stripped faster between the pads with some locking pliers(vice grips) or something. You'd have to rebleed of course, but even if vice grips don't work you've got easier access to a get at it with a welder or whatever next step you decide to go with.

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Tried fitting a pair of vice grips between two brake pads?.....remember they'll still be in the way until the pins are out..!

    • @ninjabortion
      @ninjabortion 8 лет назад

      +Moonfleet41 you can compress the piston/s to get max room, and then fit the vice grips in there, thickest ones you can. They make tiny ones, super thin, sorta thin, all the way as fat as you wanna go. Honestly seem to get more use out of my needle nose size ones than the big honkers. This is of course off topic of your video which is welding onto the bolt to get it out(well done btw), just saying it in case someone else finds this vid searching for your issue and reads comments for other stuff to try out before welding :p

  • @MrNipperz
    @MrNipperz 8 лет назад

    Excellent vid! Still my favourite channel on youtube . Keep it up! P.s. loving the new funky music!

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Thanks buddy, trying to forge new links with musicians all the time, just located an awesome rockabilly band so some even more funky msuic to come... just trying to keep things moving forward buddy!

  • @Lorddarthvader1701
    @Lorddarthvader1701 8 лет назад

    You are top notch, good stuff as always.

  • @JustTex
    @JustTex 8 лет назад

    I would usually try to use an easy out( not sure if you have those over there) but failing that it's time for the drill . But welding it sounds a lot easier. Never would have thought of that .
    Your a genius del. Cheers 4 sharing the knowledge again. ( Hope the gopro was alright)

    • @Moonfleet41
      @Moonfleet41  8 лет назад +1

      Ha ha yeah, made of granite those things... and yeah we have Easyouts here, little reverse cone twist tool...and great if you cna drill down straight...if you drift off to one side, its only goes downhill from there aye.. Good to hear from you always buddy.

    • @JustTex
      @JustTex 8 лет назад

      yeah that's them, can be useful sometimes but really is a crapshoot. Cheers

    • @allenhuling598
      @allenhuling598 8 лет назад +1

      Yeah, a square shanked (or screw style) easy out, with a little heat would have been my first try, but great solution you brought to the table too. Great tip!

  • @ImDeadSilence
    @ImDeadSilence 8 лет назад +9

    My first port of call with stripped allen bolts is just to hammer an equal size torx into it. Usually works for me.....Also I cant weld haha

    • @markward4176
      @markward4176 8 лет назад

      i had a spark plug snap in my head. spun the engine over to blow out the core then whacked a torx bit into the hole with a massive hammer! took a 1/2" long arm to shift it

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Thats a good method, usually works on regular fasteners....but even that can strip out when they are proper seized on place... also its not too safe hammering anything on a brake caliper, they're pretty fragile cast ally.

  • @rich19633
    @rich19633 8 лет назад +1

    Good one Del I was hoping you would say weld something to it. I have already replaced with stainless after a similar incident on the from ones . I now routinely just give them a few turns in / out a few times a year.

    • @Moonfleet41
      @Moonfleet41  8 лет назад +1

      Good plan my friend, as I said a while back in all of the caliper cleaning videos, routine cleaning will make your brakes last a lifetime... once you've got the stainless pins in, you can stick them in an electric drill to polish them in the future and keep the pads sliding freely!

  • @suzuki750stu
    @suzuki750stu 8 лет назад +1

    Great advice and how to video buddy, I'm gonna have to take a trip to machine mart and get me a damn welder, keep saying I'll get one and never do, regards Stu 👍👍🔧✌️

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Keep an eye out for their VAT free days - if you register for their newsletter, they will periodically send you a VAT free voucher - all helps aye buddy !

    • @suzuki750stu
      @suzuki750stu 8 лет назад

      +Moonfleet41 yep buddy, already registered, got my tool boxes that way 👍🔧🔧🔧

  • @mrjleex
    @mrjleex 3 года назад

    Just a question re torque. There are two types: Lubricated and dry. The same bolt will have different torque values. The Triumph manual warns "never lubricate a thread unless instructed to do so". The rationale is that the lubricant reduces the friction and results in an over tightened condition and a possible fixing failure. For the brakes, lube is called out on the caliper pins. For the rear wheel spindle, there is no lube callout for the 85 Nm torque. Future jobs might be better if you didn't lube the end of the spindle. This information comes from Service Manual T3859909-01 issue 4, 10.2004. I really enjoy your videos. So superior to the manual. I currently have a stuck caliper pin. I'll try the epoxy or the torx bit fix rec by David L.
    I am a degreed manufacturing engineer, so have background in the fastener field.

  • @filipefmelo
    @filipefmelo 8 лет назад

    Wow, hat's off to you, good sir.

  • @mattbridge6925
    @mattbridge6925 8 лет назад

    Awesome video as always I look forward to these more than the walking dead ! Haha

  • @GTsGarage
    @GTsGarage 8 лет назад

    Great tips fella... sure I will be using both at some point. cheers for sharing..

    • @Moonfleet41
      @Moonfleet41  8 лет назад +1

      Cheers mate, good to hear from you... and conrgatualtions on the big Tiger.. welcome to the club buddy, hope you're running the chain loose as they have quite a severe arc sweep and when you are riding two up with luggage as you do, you need the chain tension more like a moto crosser than a road bike - but you know that I'm sure !

    • @GTsGarage
      @GTsGarage 8 лет назад

      I didn't m8, it was loose by an additional 5mm either way more luck than judgement on my behalf. Cheers for the info fella, as always appreciated.

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      NO worries buddy.... its a common known trick with the Big Tiger (and they are the biggest tiger ever too lol) just drop a couple of bags of gypsum on the back seat when you chekc the chain tension.. sets it bang on.. Oh, and are you coming down to the Jurassic weekend in September.?

    • @GTsGarage
      @GTsGarage 8 лет назад

      Cheers fella, will invest in a couple of bags for the weekend :) We're hoping to get down to do a coastal run this weekend starting in Kent this weekend, but will see how it goes as I need to give her a service and replace the front brake pads. Not sure about the Jurassic yet m8y, but will try and get down for it.

  • @kennynvake4hve584
    @kennynvake4hve584 5 лет назад

    And yes...the bolt will seize into place without any thread lock...when I worked on Yamaha bike's, I was told the reason the metal locks together, is because they are usually two different types of metal...and because of that, the ionization between the two materials will (weld) itself together...I have broke many, many screws that hold the signal lights, and kill switch to the handle bars for this reason.

  • @AbouzarKaboudian
    @AbouzarKaboudian 8 лет назад

    Great video Del! Thanks for sharing ;-)

  • @tinks43
    @tinks43 8 лет назад

    (P) Easy with the right tools 😀 & good to see the vfr tucked away in the corner 👍

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Who put that there?!

    • @tinks43
      @tinks43 8 лет назад

      +Moonfleet41 I wonder! Lol, just been and checked my pins and thankfully they came out so lubed them up a bit as a precaution.

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Good move buddy, investing in the future !

  • @matthewburgess6898
    @matthewburgess6898 4 года назад

    Hi ya watched ya blog on getting brake pad bolts out of the triumph I two had trouble with america took cailper off put in vice drilled into bolt then wacked a Allen bit into then a socket and ay presto I got them out today thank God ordered to stainless steel ones great vids keep them coming

  • @mattgalek4475
    @mattgalek4475 Год назад

    Haha, so, I got the same monocast problem on a 85 v65 honda sabre. Only problem is that the pins don't even have a allen key slot. They're just solid on both sides. This is the only video showing up for me too lol.

  • @edsmith2650
    @edsmith2650 3 года назад

    2021 Thank you!!!

  • @jamerson808
    @jamerson808 7 лет назад

    Great welding tips👌

  • @stevensteel8617
    @stevensteel8617 2 года назад

    This is the problem I have on my NC750XDE parking brake pins. Of course I don't have a welder. Unfortunately they seem to have been over torqued so the heads have rounded, but because the parking brake shouldn't wear much they don't usually get changed either. I know that once I succeed in removing them they will need replacement so I searched but though you can get the pads because they fit other calipers too, only Honda seem to make pad pins for these. Alas Honda also put thread lock on the whole thread, all 6mm of it! I have tried drilling deeper and using some amtech screw extractors, but I can't get it to turn the pin using a standard 6" tapping wrench. Then again I also have the challenge of trying to hold the caliper because my pad pins are on the inside of the caliper. I also tried wd-40, break cleaner and engine degreaser to try to free the threads but to no avail. I also tried heating it with a heat gun but I was scared to go too hot so that didn't help either.
    By the way I already changed the seals and also fitted stainless pad pins and pistons on the front and rear hydraulic brakes because they were badly corroded, which your videos helped me have the confidence to do thank you. I may have to try the epoxy and disposable allen key trick, though I still think it needs more heat. To be seen. Ironically these calipers are over £100 second hand, being rare, and often come from abroad with high postal charges, so I hope I can get this sorted...
    Thanks for your videos. Hope Penny's ok too.

    • @Moonfleet41
      @Moonfleet41  2 года назад

      Sorry to hear you're having this trouble.. have you tried tapping a torx bit into the rounded alun key hole.. usually works to get a bite in it, and if it has threadlock in there, then heat will help to not only melt the glue...but also expand the casting slightly and help release the screw !! Thanks for your feedback too, and good luck with your task mate.

  • @martincarey8620
    @martincarey8620 8 лет назад

    Great stuff as always Del !! On my old ZZR600 they were not threaded, just held in with split pins... Still an absolute bugger to get out though...and always leaned them using the electric drill method :-)

    • @Moonfleet41
      @Moonfleet41  8 лет назад +1

      TBH mate, those split pin ones are the best, however, stuck they get, you can drift them out from the other side... then bung them in the drill like you do... the screw in ones are a pain in the arse...!

  • @fiftyracer192
    @fiftyracer192 8 лет назад

    Had to do a load of exhaust studs in a mates bike last week just set a nut over the stud and welded it straight to the stud.

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Anyhting that works aye buddy... nice one.

    • @fiftyracer192
      @fiftyracer192 8 лет назад

      +Moonfleet41 yeah just used what I had to hand lol was awkward to get the bolts to sit centred there because they were too big. Seized things are my least favourite job by far

  • @DerbyshireBrian
    @DerbyshireBrian 8 лет назад

    Great video Del, good for future reference for if/when I come across this problem. cheers.

  • @siamakuk2004
    @siamakuk2004 7 лет назад

    Encountered the same issue a while ago on a varadero,identical caliper,rammed a torx bit in and got them out

  • @pauvy2070
    @pauvy2070 4 года назад

    thx

  • @skeverd
    @skeverd 8 лет назад +1

    P- Where was this video a few months back? Haha, had this issue with the triumph trophy caliper. I was rapidly running out of options, so with a used caliper on my watch list I decided to 'gently' ;) tap an oversized security torx bit in. Worked beautifully!

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Well saved buddy... glad you got it done..! scary ainit..!!lol

  • @AngryBiker751
    @AngryBiker751 8 лет назад

    I was told that if you put any stainless steel in to cast aluminium you all ways need to use copper grease, as stainless steel causes a reaction to cast aluminium, if you don't it weakens the cast aluminium. just a tip for people that didn't know

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Not quite true my friend, otherwise the pistons themselves would seize in to the caliper body, wouldn't they? Certainly in the presence of salt , this corrosion can occur, but it's easily broken away because the stainless itself doesn't de-grade , unlike zinc parts, fitted dozens of sets of stainless pins and, as I demonstrated in this video, always with CopperSlip and they never seize in place again... the beneift of the stainless pins is that the straight shafts don't go rusty and stop the pads moving...

    • @AngryBiker751
      @AngryBiker751 8 лет назад

      sorry i wasn't on about the brake calipers, just stainless steel in general, the only time i use copper grease on calipers, is behind the brake pads to stop them quelling, del you are legend of the bike world. without your videos i wouldn't get where i am today fixing my own bikes and friends bikes

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Thanks Mitchell, you are very kind buddy.. much appreciated. Del.

  • @lsforce
    @lsforce 8 лет назад +1

    Hi Del, why didn't you try to use an extractor bit - I had the same nasty experience but with the caliper bolt - tried some other options before like hammering big ass screwdriver and almost breaking my wrists trying to undo it, tried to grind the head to fit 12mm spanner - broke two spanners, heating it - nothing helped... After 4 hours I remembered I have bought a set of extractors a while ago, so it took me just five minutes to get it out... Since then I worship them and frankly they never let me down (0h, did I mentioned I drive a Honda :))

    • @Moonfleet41
      @Moonfleet41  8 лет назад +1

      I think you mean an 'Easy Out', which I have got a set, but they need at least 1/2" deep hole to get a good 'bite', and this socket cap is barely 4mm deep, so it wouldn't get enough purchase, maybe I should have said this... I could have drilled in to it, but chose this method instead !

    • @lsforce
      @lsforce 8 лет назад +1

      +Moonfleet41 it's possible - never got more than 5-6mm depth - yeah, you need few tries to make it catch... I guess I can do it because I don't have welding equipment and it's the last option for me... I am glad I have learned another trick from you - sure I will use it some day when I got mig welder - thank you!

  • @instructormaint8423
    @instructormaint8423 8 лет назад

    A beautiful demonstration! *thumbs up* A good thing to remember is to have your welder ground "earth" connection close to your work area.
    Be careful not to have the current path going through bearings and pivots (wheel, steering, linkages etc). For example: It could be tempting to clamp onto the brake disc only to find that you welded your wheel bearings. Never been done before right? :^)

    • @Moonfleet41
      @Moonfleet41  8 лет назад +1

      Too right, good advice mate, but if you do a more extensive welding course, and get involved in the deeper stuff, you'll start to look in to current transfer and exactly what you described, the grease in the bearing acts almost as a flux and then you'll spot weld the ball bearings where they touch... wise words well said mate !

  • @iritantNL
    @iritantNL 8 лет назад

    Nice solution :) I've also have good experience with torn wrench hammered in to the hole and get it out that way :)

    • @iritantNL
      @iritantNL 8 лет назад

      Torx

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Yeah, thats a great tip, and often works... but even that rounded out on this one..!

  • @kevinkille
    @kevinkille 8 лет назад

    Tell us about the new bike Del XD

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      .... new bike?? What new bike would that be, this is The General remember, I've had it a couple of years now, I know it's not been shown recently, but it's still here... !

    • @kevinkille
      @kevinkille 8 лет назад

      +Moonfleet41 The grey one in the corner xD

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Just a future project bike, maybe for next year.!

  • @drwombat
    @drwombat 8 лет назад

    these are a pain in the ass when they won't budge but to add insult to injury... sometimes there is a threaded cap that covers this bolt which also gets glued stuck. hammer impact driver helps

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Yeah they can b a biatch.. its SO important to only do those little caps up finger tight and lots of copper slip.. often they only have a screw driver slot aye.

  • @8ball903
    @8ball903 8 лет назад +1

    ' adapt and improvise !' ... Military through and through. 👍

  • @CrazySparkie63
    @CrazySparkie63 8 лет назад

    I normally find my Wera allen keys work (the ends are almost like Torx profile also you can put a power bar on them and lean on them, yes they bend but don't snap and straiten themselves up after.) If not them I resort to the Torx and impact driver method

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Always avoid impact drivers on calipers, you end up hitting for too long, these pins are not tight, and then break with a crack which many fasteners do, they are tight all the way out , as you saw... as even when the thread was free, the pins still hung on to the pad inside the caliper, so the impact driver is a bit redundant...

  • @andyhutch8262
    @andyhutch8262 2 года назад

    Fill alan key hole up with coarse grinding paste, push good quality alan key in and slacken away.

    • @Moonfleet41
      @Moonfleet41  2 года назад

      Good method, i made a video of that some time ago. !

  • @Steff320i
    @Steff320i Год назад

    You have a great accent.

    • @Moonfleet41
      @Moonfleet41  Год назад

      Thanks mate.. glad you enjoyed the video. !

  • @bee17167
    @bee17167 8 лет назад

    EZY outs may work they have a drill bit then a splined driver you drive in too drill hole cost a shit load so I lend one works a treat I also think the tap helps break the lock

  • @robbiegwinn
    @robbiegwinn 8 лет назад

    wow 4 bikes...how cool
    good video...i hate those allen screws would much rather have a socket type bolt

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      4th bike?? I couldn't possibly comment on the stunt bike donor bike, so... no comment !

    • @robbiegwinn
      @robbiegwinn 8 лет назад

      lol...

  • @zakmartin4722
    @zakmartin4722 8 лет назад

    you should use a flat head screwdriver the same size at the hole and hammer it in and unscrew it that way had saved me a lot of times before

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Works on bigger socket caps, but this is a 5mm hole... and both the torx bit and a screw driver bit weren't stout enough to do much more than reem it out even worse!

  • @HoldSimp
    @HoldSimp 8 лет назад

    Another excellent video Delboy. If no welding equipment or J,B weld, could you cut a line into it if there is enough head showing for a large screwdriver?????

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Hi buddy, you can only any normal socket cap but this is screwed in flush with the surface, so that would damage the caliper... but always good to try anything if you have to...

  • @kennynvake4hve584
    @kennynvake4hve584 5 лет назад

    You can use an american allen wrench...or what ever the one your using, use the opposite one, of a different size...like..if its metric...use an english...and if it's english use an metric one...and find the size that will start to go into the bolt and knock it into the bolt head with a hammer, in other words force the allen wrench into the remeded out bolt. Sometimes the wrong size allen wrench will go into a remed out bolt head..and then it will grab...

    • @Moonfleet41
      @Moonfleet41  5 лет назад

      Not sure if you mean allen wrench, or Torx bit?... thats the accepted trick.. the "star" shaped tool bites into the reemed hole and gets a hold..!

  • @DukeDyson
    @DukeDyson 8 лет назад +1

    I hope you disconnected the USB port before welding :)Great tutorial buddy

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      No , I left it connected hoping to burn the f*cker out lol !

  • @timbarnett3898
    @timbarnett3898 5 лет назад

    JB Weld to welding? My actuator ring on end of key cylinder on Dodge truck broke. J B weld was first thought, but failure. So, cleaned real well an Superglued for a one time trip to ordered part at auto parts. I would have tried Superglue before welding. But hey, Your points will even go up if you can. Then ad I'm thinking about needing to remove battery you bring that up, very nice! So I stopped video to comment, let's see rest an check out the weld, haha!

  • @crabsodyinblue
    @crabsodyinblue 4 года назад

    another option can be using a bolt extractor, given there is enough left to grab and not damage the inside thread. worked on my ST1100. Came here to find about stuck calipers :-0 , so you're saying soapy water? i recall pertrol being used back in the day?

  • @russellnapier3884
    @russellnapier3884 5 лет назад

    Nice vid. I had the exact same problem on my Tiger and ended up having Triumph replace the calliper at £500 + VAT 😢 Next time I will look for a replacement on EBay

  • @spyuggy
    @spyuggy 7 лет назад +1

    I am also rebuilding a Kawasaki GPZ 550 (1986) the fork stanchions are well gone, I put the allen key onto the hole and it just ripped around it, problem is, the bottom of the fork leg does not split for the spindle, so a long allen key was needed, now I have to find a way to remove this arsed up bolt, I shall try JB weld first, as the bolt is rotten.

    • @Moonfleet41
      @Moonfleet41  7 лет назад

      Just drill the head off it Doug.. use a drill bit the same size as the bolt shaft, and the hole in the middle of the alun bolt will centre the drill... then once the head spins free attached to the drill the fork will come apart, and you can remove the stump of the bolt with some grips once the damper rod it out... Good luck with it buddy.. Del.

    • @spyuggy
      @spyuggy 7 лет назад

      Thanks Del.

  • @bobbywilson7838
    @bobbywilson7838 6 лет назад

    Hey Del surely removing the Caliper from the disc and using a pair of small vise grips on the smooth section of the pin between the pads would allow you to gradually turn it out? Obviously with the hydraulic line still attached.

  • @perrylaithwaite2526
    @perrylaithwaite2526 8 лет назад

    I have a row of certificates but always classed myself as a mechanic, never a technician lol

    • @Moonfleet41
      @Moonfleet41  8 лет назад +1

      That's good to hear mate ! A thinking man who can noodle out a problem and improvise a solution is pure mechanic!

    • @perrylaithwaite2526
      @perrylaithwaite2526 8 лет назад

      Yep defo. Made a gasket from a page out of a book in the middle of the channel and a woodruff key for a water pump out of a drill bit in the Atlantic. On a boat engine of course.

  • @thebizzas
    @thebizzas 8 лет назад

    Top job I have done that Job myself just a couple of things cover your
    brake disc also so you don't get any stray spatter on it and in my case take
    off your £500 watch for 25 years service 1 week after having it

    • @Moonfleet41
      @Moonfleet41  8 лет назад

      Blimey, bad news on the watch mate, I've done that to a camera lens in the past, just a random molten spark is all it takes... even worse, when they fly up in the air and land on the back of yer neck, which is why I now spin a baseball cap round backwards !

  • @80srule39
    @80srule39 2 года назад

    Thanks for this, ive got the exact same issue on my pgo gmax front caliper, ive got a welder, do i try it, or the jb weld....great vid...

  • @brmelectric
    @brmelectric 8 лет назад

    thats true however the set I have made in USA are from KD tools. i think they would work. part # 720. check them out.