The longer the better! Its good to learn more about the subject than just the basics. What works in different ways and why. People dont learn by just getting directions. Its good to know why something works in one way or another
@@tommyapples8490 this is a horribly inefficient approach to obtaining information. "The longer the better" - Actually, no, the more concise and relevant the better. Don't get me wrong, I don't want to knock the kid but I found myself jumping around like crazy to try get the pieces of information that were relevant and skipping the stuff such as "THE MONSOON IS THE BEST, IT'S CRAZY" type of rambles. He has a lot of good information to share but I don't think it's inappropriate to delivery constructive feedback (not that this comment was constructive above), and suggest that perhaps he re-watch his own video and clip out just the parts that are crucial and he will likely be shocked to find that the video went from 39 minutes to 5 minutes.
Everything about this channel is awesome but the best thing by far is the lack of commercialization. No plugs, no sponsorship, no FN ADS . I almost forgot some people just want to help others out.......just because. Thank you and your team very much.
I heat up my drill bits, using a culinary torch, before drilling. Cuts through the plastic like butter and seals the edges so there are no sharp spots. Only heat until it will slightly melt the plastic and reheat as needed. Have never cracked a single plastic project, using this method. Holding a board on the other side of the plastic is a pain, but it can work. Tape just leaves a sticky mess on my drill and my tub. Make sure you're not using your good wood or metal cutting, bits. The heat can dull them.
Yo that's smart I never thought to heat up the bit. I guess just make sure they are strong good bits right? Since heat and pressure when using the drill could break one, right? Imma try it next time and see if it helps Thanks for sharing!
@@Growingdopamine818 I would use the crappiest bit I have for this application, cuz once you do the bit is ruined. The good bits are hardened steel. You apply heat like that to a hardened bit it loses its temper, and ruins it
@@DPW13 it was a demonstration why you got to be a little bitch I bet you got nothing goin on .punk do you . I don't see your video on tube. RUDE .Apologize please.
After I have taken high doses of psychedelics, I found that some people still feel imprisoned of their minds, what worked for me was mycena caps. It helped me find more of who I am after the psychedelic doses. But remember we are all like snow flakes every individual is special in their own way as life intended. Gratitude positiveness and prosperity
Tip for making the fan hole: grab a old tin soup can from your pantree that matches the girth of the fan, empty it and put the open end on top of your oven on high heat, wait a couple minutes and it will melt right through the plastic leaving a nice clean circle
I like that you talk to the viewers as your friends. Keep being long- winded and as thorough as you can. Your videos are useful and thanks for making them.
Thanks for the information. I am still a bit confused about a couple of things. First, is the fan blowing air out of the tub? Second, can you please show a picture of the final assembly of the setup? Thanks.
A few tweaks I would add for the fan setup. You can place the detached fan screen INSIDE the tub (sterilized first) for a more flush fit. Then you can use micropore tape to completely cover the fan hole on the outside of the tub. Once taped, screw the fan on. This will still allow FAE with the benefit of filtering the air. Note: When in spawn mode, tape over the fan with painter's masking tape. You can take the tape off when ready for fruiting.
I live with a bartender and have a ton of cocktail shakers laying around. The top drainage portion makes perfect size holes for 50-70qt monotubs w/polyfill imo. Toss it on a red hot stove, grab a pair of pliers and depending on how hot you get it you can knock 2-3 holes out per heating w/ no cracks or jagged edges where moisture and bacteria can build.
I've been drilling into my tubs without any scrap of wood and literally 0 cracks. As long as you don't apply a significant amount of force on the drill, you shall achieve 0 cracks as well 👍
You should always hold a piece of scrap wood behind the plastic tightly or lean down onto it as you push through gently with the drill bit. It wont ever crack.
You're the friggin MAN! Willi Myco for President! Thank you you're a life changer much appreciation! Keep up the amazing work everything I've watched is a true gift!
Hey Willy, the crap tub I got with "kit" didn't work , grew about 7 mushrooms at different times and lots of failed pins so I'm building this tub.I'm Not sure if it was mentioned somewhere in comments but I used a piece of scrap wood behind each hole i drilled to keep from cracking , tape works too usually. Just a little helpful tip for the RUclips peeps.
@@sourcecodex3189 First off Isolation is most commenly being refered to when using MSS because there is work to be done and it can take time and effort and clones and lots of plates to get the genetic up to full canopy flushes ect, or like i said you can by LC online with good genetics and just put it on agar if you want to save the genetic. If you are really using the term "isolation" while talking other than MSS its not hard at all and your statement becomes void lol.
@@ianplattner9930 First off there are many ways to isolate a strain and the current most popular on RUclips which is the platform we are commenting is transferring from agar to agar. So I’m still correct and you still look like an ass
Got a question about the fan. I've never grown mushrooms. Just been doing a bunch of homework on what to do and what works best for me. But the fan. I couldn't tell maybe I missed it. But is it blowing the air out of the tub or in?
3 oz or more would've been a good first flush. This is what happens when you try to "automate" an already effectively automated system- diminished yields. Automated failure
If you know or want to learn a little electronics, you could use an Arduino to run the fans, misting and lights too. It has a built in timer. You can find code to copy and set it up pretty easy. Arduino has endless possibilities.
3:55 action starts Love the video but the intro was super frustrating to sit through, I already know what the video is covering and everyone knows to subscribe/like in order to follow/support your content. In the famous British words: “Get on with it.” Otherwise thank you for taking the time to add you knowledge to vast database of the World Wide Web. It’s most helpful and your intuitive insights are gems now added to the collection of my knowledge. Bravo.
@@patbloodysabbath8488 oh entitled and frail human ego, dost thou truly feel that your power is so great as to command me to do as thy will? Not apologizing for a very mild comment I made regarding the honest expression of my experience with this video. Especially when I finished the comment with a compliment, a word of gratitude, and a Bravo. You better watch how you talk in public because the internet protects here you from getting slapped for that kind of arrogance but in the real world people do not tolerate monarchial commands from some petty pauper like yourself. Tread carefully with thy tongue, foul snake.
@@marklange121 Not saying he should remove any content, he should just talk over the video with him doing things or put a pip window in the corner of himself. But i personally find it hard to watch someone talk when there are some many better ways to express the idea usually.
@its possible I agree because I'm a visual learner but its hard to really get everyone's learning points ig but you can do both with showing and talking.
Do you setup your fresh air fan to blow air into the tub or suck the air out of the tub? I couldn't really tell by the video. And is it the same with your walk in grow tent? I have both and am wondering how to setup my fan
The fan: www.acinfinity.com/quiet-usb-fans/ The Monsoon: www.petswarehouse.com/exo-terra-monsoon-multi-system-pt2493/?gclid=Cj0KCQiA-rj9BRCAARIsANB_4ABEVDxfqr9OdLE2iYADiLDbkhvtaEfb5QLNZU8Gvm1ry4kTs-wOJTkaAgVSEALw_wcB The timer: www.homedepot.com/p/myTouchSmart-Simple-Set-Indoor-Plug-In-Digital-Timer-26892/207032979
Better to use a fog machine that utilizes a humidity guage inside the tub rather than a mister.. when the fan comes on and the humidity drops, you can set the guage to come on when it humidity hits 70 or 75% then turns back off at 85-90% RH, wherever you want the guage turn turn on/off at, it can be at any RH you want..and it won't come on again until the fan blows out the CO2 3 or 4 times per day or it shouldn't If you've got the right temps and correct sub depth and saturated at field capacity.. i use a pseudo casing with left over sub. I haven't used automated in awhile, now I use 2x 2" inch holes down low on both of the long side right in line with my sub line at 3.5 inches so I'll put the holes at 4 for my 0.5 case. Then I'll put one on each of the narrow ends of the tub about as high as I can go, then I'll cover them with either a filter disc (once I introduce fruiting conditions at 80% colonization) or 2 layers of microtape after removing the masking tape that was on there to prevent FAE during colonization of my substrate. I don't even have to mist or fan, the humidity stays perfect and since it's a small room my HEPA filter inside cleans the air while also moving the air around to help out FAE, so It's set it and forget until harvest. I just keep and eye on the temp outside the tub, i like 70-72 in the room because that will mean it'll be 72-75 inside the tub, it's always 2-3 degrees warmer inside. Biggest issue people run into is taking the lids off constantly which changes the humidity inside and it can never stay consistent, so it has to basically reset and rebuild the humidity which dries the cake out more and more each time, it lowers the temperature inside the tub by multiple degrees each time it's removed.. as long as you aren't getting those fuzzy feet that are trying to walk up the base of the mushroom thats short and fat like a chode, you're fine when it comes to FAE. I almost feel like people need to invest in a C02 reader, just to make them feel more at ease. Leave the lid on, just look at it through the sides and you'll know if there's any issues based off what the mycelium and/or mushrooms are telling you.. Another issue is over misting, people mist directly on the cake while there's pins, thats a good way to get aborts. If I do mist, I never mist the cake once there's pins and i try not to at all once after i put it into fruiting conditions because it retains so much moisture.. but, if i do, I always mist the sides and the lid and I make sure there's no big water droplets that will run down and drop on the mycelium/pins. The second flush I'll mist the sides and lid real well, then put the lid back on like the first flush.. the 3.5" sub depth with a 0.5" pseudo casing layer will provide plenty of water and nutrients for the mushrooms to pull from, it won't be getting low on moisture... yes it costs more in spawn and grain to do it, but if you only have 2-2.5 inches of sub then by the time it fully colonizes it's going to shrink about a half inch or more depending on the humidity you retained and with a fan you're going to lose more.. so do you want to lose money going towards good grain and sub, or spend less money and just not get the yields? Either way it's a loss, id rather get the big flushes cause honestly, a few grams pays for the extra materials. With a think cake the next flush will be even smaller as the cake shrinks and so on as it runs out of water and nutrients, that's why many people can't get a third flush even with soaking the cake... So it drastically limits your potential 2nd and 3rd flush, especially depending on the type of mushroom, some of them can suck up a lot of water lol. But with all that said, it always depends a lot on the genetics if they're high yielding or good for multiple flushes. Even if it's the same species or sub-species but with two different genetics, one might flush a really strong canopy once, then get progressively worse until its no longer worth it to maintain. While another might not be a solid canopy the first flush, but it has some pretty consistent flushes so it may weigh out better in the end but be a drastic difference in potency. All of that depends on the genetics...we can only give it the things it needs to be able to grow to it's full potential that it's genetics allows for, thats it. Which you'll learn what it likes and if you take a clone from the first run with a mushroom with solid genetics, the second run it'll be used to those conditions, the tub size, temps, moisture, the type of substrate and grain spawn, so the mycelium and mushroom adapts and starts thriving better if you repeat those same conditions. That doesn't mean you can get good results with poor conditions though, theres just variables that they're able to get used too. That's what sucks about multispore...you've got no clue which of the genetics is going to germinate, no idea about any of it's traits like you can easily find out with LC or spawning from agar straight from the guy who isolated/cloned it. You may get an amazing one in a multispore, I've gotten pretty lucky before, sporeworks is always pretty solid, and then you can clone the best looking mushroom to agar or a slant to keep the genetics to work with in the future and keep cloning the different generations from there.. Or you'll get a multispore that germinated that turned out to be trash, either small yields but good potency (or small and weak, worst of both worlds), or like me the very first time, I had huge yields but literally zero potency and I mean zilch, 8 grams and not even a microdose. Back then I thought i did something wrong but i couldn't figure it out since the looked so healthy, i was pissed, but I finally realized it wasn't my fault... i did everything i was supposed to do and i grew a lot more than i expected and i could take what I learned moving forward, so its never a total waste as long as you gain experience in both what to do, aswell as not to do. I don't think that spore shop even exists anymore, I know I've heard nothing good about them but it's my fault they tricked me with a gimmick. Since I was new back then i saw they were selling a spore syringe with water/activated charcoal so it was solid black, it was to help prevent contams, which, maybe it did exactly what is said cause I didn't lose a single BRF cake, but man, did they ever put the wrong genetics inside... I went to sporeworks after that, best place for a multispore IMO. Now I get genetics by LC syringe or on Slants that I can store for long periods of time in the fridge to slow down colonization and transfer it to LC when needed... I've heard vaccum sealed and stored away in the fridge away from light they can last a couple years on slants, even a year or two in LC in the fridge that has been slowed down. I've even heard of people freezing colonized grain bags, slants, and LC, but I've never had the guts to try it. Maybe if I run into some not so good genetic material I'll freeze it in multiple mediums for 2-3 years vacuum sealed to prevent freezer burn, then try bringing to room temp slowly and then do a transfer from the slant or LC to a agar plate and then grain into some substrate to see if it begins to colonize, or if it continues colonizing the grain bag if it hadnt full colonized before freezing. Which I'll probably mark the growth with a sharpie just incase it does something weird like slowly grow on the surface or something while frozen You can buy a hose splitter to do two tubs, but youll need to refill your fog machine up more often.. remember to remove the hose and machine every few days to steralize with alcohol. The fan is great... and the awesome thing about the fogger, it'll come on any time it's needed without the fan if RH isn't where it needs to be. And it's not a mister, it's a legitimate fog just like when water evaporates and then falls back down. Just be careful if you point the hose upwards, you can get water drips so it'd be better to add it to the top straight out and fog will fill the whole tub equally and basically the cake will only absorb what it needs and there's water build up on the cake.
Is there a giveaway? Awesome vid although I wish there was more illustration, showing the drilling etc. More than talking but still very informative! A starting myco here about to fruit my spore and this is the most nervwracking part Monsoon solo on amazon is 89$ where is it 40$??????
Stop hating. Some people don’t do well with the readers digest version. This way he caters to everyone. If you don’t wanna see it all just fast forward to the part you need to see.
@@justinely9073 he's not catering to everyone if the snappier students are bored off their nut, and constructive criticism isn't hate so stop diluting the word.
@@repinsJ I’m still confused about the process of spawning to bulk. With BRF cakes you just leave them in the jars until they’re fully colonized. With monotubs, your grains must be fully colonized and then you introduce them to your bulk substrate. Then your bulk substrate has to fully colonize before moving to fruiting conditions. I look at this stage as being similar to birthing and dunking your BRF cakes. What should the mono tub look like before moving to fruiting conditions? Obviously the tub is much larger than a mason jar, so do you replicate the conditions of the mason jar (a closed system with small gas exchange holes) before starting the misting and fanning process?
I needed one of these all mine died when i was in hospital. Unfortunately they dont seem to be for sale anywhere and where they are there sold out. Ive bought a humidifier and a plant drip feed aystem instead together do you think theyll work?
@@nachospopthe3rd564 It worked out great! I am loving growing mushrooms! With the long shifts I definitely had to check it last thing before I left and first thing when I got home but I was so excited about it that was no problem anyway! lol Have fun!
Is this automatic misting system better than using an automatic humidifying system? There are ultrasonic humidifiers for reptiles for around the same price that allow you to set a target humidity level instead misting based on repeated intervals and times.
Gotta be honest this is painful to watch. This guy is like the rough draft of an essay that really needs to be edited. Tons of useful info surrounded by useless rambling.
That's the problem with "uppers" crazy smarts bound in painstakingly dry rambling. Absolutely great info, no disrespect or judgments intended, purely an observation.
@@trupyrodice4462 What makes you think he’s taking “uppers” besides rambling? Also I hope you don’t think shrooms are an “upper” lol? Also it’s not cool to assume someone’s taking any drug, that might just be their natural behavior
This works great! While in colonization I taped everything up with painters tape then after four days the sub was 70% colonized. I then cased the sub with 50/50 mix and 6 days later I put in fruiting conditions. I did not start misting until day two of fruiting. You will see pins at this time possibly. once I put to fruiting I fan 3-6 times a day, 3 times auto from timer then 3 additional manually. on day two to day three I start the monsoon mister every eight hours and leave the automated set up and check on it once a day without having to do much at all. I used medical tape after removing the painters tape on the large holes during fruiting and left the small holes on the bottom uncovered. I have pins on day two of fruiting only fanning for the first day or two RH after fanning drops to 88 after a few minutes it's back to 93-95 RH temps remain around 76-78 love this set up. I can't wait to try Panaeolus Bisporus next
Ghetto tek = polyfill; any big box store in the craft area. Pro tek = 0.2micron filters; lots of options to choose from. For this design in particular you could probably fit syringe filters in all those holes. The filters restrict the air flow and more holes may be preferable. Or, use a high pressure air pump like a nebulizer and push fresh clean air in, while pulling the old stale air out. www.amazon.com/s?k=syringe+filters&ref=nb_sb_noss_1 I would advise doing your cycles opposite of how he describes in this video; first run the fan, then the mister. The moving air will dry things out a bit. It also more close replicates natural conditions, where the wind picks up and then the rain comes.
Hey Willy, I have quick question. I'm an amateur, can you explain to me why I would need FAE holes when you already have Gas exchange holes in the mix? I thought the FAE was a feature of the shotgun fruiting chamber and Gas exchange holes were traditionally for monotub tek? Thanks for your help.
What I have found, when using drill bits to make holes in plastic is NOT to use a drill (because it usually cracks), but take the drill bit and heat the end of it with a torch and MELT the hole in the plastic.
Personally, I’ve found that you really don’t need artificial light at all. If you’re going to use artificial light, you can fruit tubs perfectly fine using the light on the ceiling of a room, and even just with the natural light that comes in the window. You also only really need 4-6 hours of light a day, not 12. I’ve tested 12 hours vs 4-6 hours and the results were identical. So don’t waste money on electricity doing it for 12. Imo best bet is to use natural light. In the window or even just in the room. Super easy, no hassle.
OmniClimHazard I don’t think the details matter lol mushrooms will grow pretty much anywhere I suppose. When I was growing I used clear lids but I doubt it matters.
@@huntercrainmusic Cool. Ill give it a whirl. Ive been a mushroom forager for over a decade and have gotten some of my best harvests from little to no light areas in the woods. I was just curious what all the fuss was about among homegrowing regarding the need for so much light. I think Ill do fine with a solid lid. ✌️
OmniClimHazard yeah the truth is there isn’t reason for any light at all. And if you do use light you need like. A TINY amount, for a very small amount of time per day. The ONLY benefit of this is to speed up the time it takes to begin fruiting. Once they pin, you no longer even need to do that. And if you leave them in complete darkness they will still fruit just fine, but will take a few extra days to start.
@@OmniClimHazard it shouldn't work, mushrooms grow towards light, they'll grow to the sides of your tub. If you want you can make it extremely compact inside the tub and have quarter inch holes all over it, and they should grow through those quarter inch holes.
The fan is on the outside of the lid, blowing air into the tub, correct? Also, where does the power cord for the mister go? Are there cables running through the gas exchange holes?
If you have a drill with a slower speed- use that, and if you switch it to reverse, it drills slower, melting the plastic and leaving cleaner holes without cracking. I love your FAE design! 👍
I’ll edit your videos for free to save everyone all the unnecessary talking and over explaining, all your videos could be half the length at least. Still appreciate the effort and information you share but damn bro it’s exhausting
The over explaining is perfect for people that don't know very much about it, some of us have more knowledge with this, and others have no knowledge. The off topic stuff might be annoying but for people that have less understanding, I'm sure they really appreciate it.
@@trevormerivale6882 Nope, I don't know much and I still couldn't watch. Over explaining can easily be remedied with simply planning an Informational script for the video to go along with for fluidly giving information and efficiently progressing through the topic being explained. ...oh and to end the video summarize the main topics and important points to write down. I just went to another channel. (I didn't just complain, I gave a solution too, so don't yell at me.)
@@rjennings0142 that's fine but that doesn't mean it's not helping people out there. In life you can't please everyone all the time. You are more than welcome to watch a different video for the information, you obviously know that because that's what you did.
He said were gonna keep this video short and sweet then talks for literally 40 minutes seriously stop talking homie and tell us how to make it and what to do...
I followed 55 perps who also did videos,on youtube on how to grow 3 years ago ,and WILLY is the only one who knows what is up.the others were short and impotent as a mule. He has videos where he takes you to a Target,Ace or Walmart and shows you what to buy saying not to buy the way over priced stuff that The Hip manufacturers mark up 900%,but the cheapest of the cheap and he says: "I am telling you that this is 1/10th the price and gets the job done. After hearing his videos I had some great large crops in my bedroom.
@@RasMajnouni well if you read around on mycology boards on Reddit, Facebook, and the shroomery, you’ll realize he has a lot of non sense teks as well. The whole “slurry tek” and etc. just over complicating a simple process for very little gain when put into practical use. His Laminar flow hood tek that didn’t even include a prefilter so you’re pretty much just destroying your hepa, degrading it wayyyyy too fast. Just small details like that can be the difference between a Filter that lasts one year, and one that lasts 7 years. He has some good information but get an unbiased second opinion away from his fans in the RUclips comment section before you try anything tbh.
I've loved you since the first video I saw of yours years ago at least 3 or 4 years ago. You are amazing dude I mean that I'm a polymath much respect and love
Awesome video man! Thanks for the knowledge. Now, one question. Why a mister instead of a humidifier? Does it really matter? Keep spreading the love! One Love!
@@validZander Thanks for trying to answer my question...I understand that...however, I wanna know why he chose a mister rather than a humidifier?? Tub size don't matter, at all, humidifiers are used in fruiting chambers bigger than this tub. I feel a humidifier would keep humidity higher than a mister hence the name HUMIDifier...but I'd imagine the fanning part would dissipate the humidity faster than fanning after a mist. Hold up. Maybe I just answered my own question!? Lmao!!
Thanks for the information. Do the Free Air Exchange holes or the Gas Exchange holes need to be covered in micropore tape (or cotton fill) to keep out contaminates?
In the all-in-one bag method when you put the bag in the container what is that white powder stuff that is mixing with water it looks like that it is used for it to hydrate the mushrooms
yer a solid dude. gonna hit yer patreon. so many folks are depressed/down with the pandemic. i'm hoping micro dosing will help them out. all the best, brother.
You mentioned using the mono tub for colonization, then take it into fruiting. So do you put the grain bags in the mono tub and keep it dark, or do you colonize in the tub with everything sealed up? Total newbe, ...I don't want to regret never trying these, and I'm not getting any younger. I want to be my own hero.
I bought the same timer you shown in the video and it doesn't do 3 times a day 8 hours perfectly inbetween like the monsoon does. You can only customize a on and off time for all 3 preseta in 1, you cant edit each individual preset like you explained. I bought the one from your link. If you could explain better how to set up the timer or explain exactly what one you are using to do 60 seconds on, for 3 times a day with 8 hours in between that would be great. I have a tub going and bought everything to find I cant sync my fans to the monsoon.
@@jomammy7786 Not a forstner bit. You would most definitely not want to use a forstner bit for this application. Those are designed to be used in a drill press only for drilling flat-bottom holes in wood.
Holly Laird the purpose of this video is for us to follow his instructions 😂😂😂 how can we do that without knowing where to get the products. I don’t understand you lol
to put an end to all the confusion regarding placement of fan (inside or out) that I have seen in the comments. Willy has placed it on the outside with the airflow directed into the tub. I base this comment on the frame in the video at, 23:51/39:06, where you can clearly see the fan and its grill on the same side of the lid as the, STERILITE, name. I like this setup and am in the process of assembling mine now. If I want to take off for a couple or more days then not to worry. Pluss it will help the little guys grow up strong and healthy knowing they live in a stable home not to mention it will cut down on those peski little contamination pinch points. See yall (way) out there; )...
4:10 I'll save you 4 minutes of your life.
appreciate it
Thanks
Thank you
I wish you could save me more than that there’s always so much fluff inbetween information
Enjoy your thumbs-up.
You are the master of spending an hour explaining 3 minutes of info
The longer the better! Its good to learn more about the subject than just the basics. What works in different ways and why. People dont learn by just getting directions. Its good to know why something works in one way or another
He's keeping the beginner in mind. I think he's great at explaining things. I think he's doing great things.
@@tommyapples8490 this is a horribly inefficient approach to obtaining information. "The longer the better" - Actually, no, the more concise and relevant the better. Don't get me wrong, I don't want to knock the kid but I found myself jumping around like crazy to try get the pieces of information that were relevant and skipping the stuff such as "THE MONSOON IS THE BEST, IT'S CRAZY" type of rambles. He has a lot of good information to share but I don't think it's inappropriate to delivery constructive feedback (not that this comment was constructive above), and suggest that perhaps he re-watch his own video and clip out just the parts that are crucial and he will likely be shocked to find that the video went from 39 minutes to 5 minutes.
Everything about this channel is awesome but the best thing by far is the lack of commercialization. No plugs, no sponsorship, no FN ADS . I almost forgot some people just want to help others out.......just because. Thank you and your team very much.
I heat up my drill bits, using a culinary torch, before drilling. Cuts through the plastic like butter and seals the edges so there are no sharp spots. Only heat until it will slightly melt the plastic and reheat as needed. Have never cracked a single plastic project, using this method. Holding a board on the other side of the plastic is a pain, but it can work. Tape just leaves a sticky mess on my drill and my tub. Make sure you're not using your good wood or metal cutting, bits. The heat can dull them.
Fucking genius
Stepped drill bits make the cleanest holes in plastic I've ever had. Leaves you with a nice beveled edge.
Yo that's smart I never thought to heat up the bit.
I guess just make sure they are strong good bits right? Since heat and pressure when using the drill could break one, right?
Imma try it next time and see if it helps
Thanks for sharing!
you the man
@@Growingdopamine818 I would use the crappiest bit I have for this application, cuz once you do the bit is ruined. The good bits are hardened steel. You apply heat like that to a hardened bit it loses its temper, and ruins it
You merely adopted the mycology. I was born in it, moulded by it
😂😂😂
Molded
Lololol
with out a doubt the best 40 minutes I've spent in a minute. Thanks Willy!
28:36 "As you can see it mists really good!"(*drips water everywhere) haha wtf okay..
I thought the same lmao "as you can see it mist really good" Fucking SOAKS the bottom of the tub instantly
@@DPW13 it was a demonstration why you got to be a little bitch I bet you got nothing goin on .punk do you . I don't see your video on tube. RUDE .Apologize please.
say you are sorry please
After I have taken high doses of psychedelics, I found that some people still feel imprisoned of their minds, what worked for me was mycena caps. It helped me find more of who I am after the psychedelic doses. But remember we are all like snow flakes every individual is special in their own way as life intended. Gratitude positiveness and prosperity
Great Video. How bout depth of substrate, and what covers/fills the FA and GE holes?
Tip for making the fan hole: grab a old tin soup can from your pantree that matches the girth of the fan, empty it and put the open end on top of your oven on high heat, wait a couple minutes and it will melt right through the plastic leaving a nice clean circle
Smartttt
saved me loads of cracked tubs ,,this hack Afrecking plus
OMG genius!!
I like that you talk to the viewers as your friends. Keep being long- winded and as thorough as you can. Your videos are useful and thanks for making them.
Thanks for the information. I am still a bit confused about a couple of things. First, is the fan blowing air out of the tub? Second, can you please show a picture of the final assembly of the setup? Thanks.
A few tweaks I would add for the fan setup. You can place the detached fan screen INSIDE the tub (sterilized first) for a more flush fit. Then you can use micropore tape to completely cover the fan hole on the outside of the tub. Once taped, screw the fan on. This will still allow FAE with the benefit of filtering the air. Note: When in spawn mode, tape over the fan with painter's masking tape. You can take the tape off when ready for fruiting.
Exactly the answer I was looking for thank you
Thanks man, perfect... YOU should be myco videoing! 💯
Hey man, buy the fan have to pull the air or flow inside ? I was a bit confusing
@@Marco-sb9ko air blowing in
Is it the 40mm fan Size or bigger ?
Instead using a mister. Have you tried using a small humidifier. If so,what's your thought on that. Thank you.
Had same question sir
Me too. I have ultrasonic humidifier
I was thinking, it will take up rea estate having a humidifier inside.
When drilling hold a piece of scrap timber behind
This just helps to avoid cracking?
@@DylanCAD yessir! I use timber everytime
I work at a lumber mill so i have a lot of lumber on hand. Thanks for the tip :)
I live with a bartender and have a ton of cocktail shakers laying around. The top drainage portion makes perfect size holes for 50-70qt monotubs w/polyfill imo. Toss it on a red hot stove, grab a pair of pliers and depending on how hot you get it you can knock 2-3 holes out per heating w/ no cracks or jagged edges where moisture and bacteria can build.
I've been drilling into my tubs without any scrap of wood and literally 0 cracks. As long as you don't apply a significant amount of force on the drill, you shall achieve 0 cracks as well 👍
Oh wow! Finally someone who knows what he's doing!
Tip... temporarily tape over the area you’re going to drill, it will prevent cracking.
or you could heat them lightly with a blow dryer
You should always hold a piece of scrap wood behind the plastic tightly or lean down onto it as you push through gently with the drill bit. It wont ever crack.
Unibits works well too. But you still need the tape.
I place a wooden block on the opposite side I’m drilling from. It reduces the flex and strain on the plastic 👌
Just run the drill bit baCKWARDS its wayyy easier. duuuuuhhhh
You're the friggin MAN! Willi Myco for President! Thank you you're a life changer much appreciation! Keep up the amazing work everything I've watched is a true gift!
Hey Willy, the crap tub I got with "kit" didn't work , grew about 7 mushrooms at different times and lots of failed pins so I'm building this tub.I'm Not sure if it was mentioned somewhere in comments but I used a piece of scrap wood behind each hole i drilled to keep from cracking , tape works too usually. Just a little helpful tip for the RUclips peeps.
They forget to tell you that you have to Isolate the mushroom strain if you want consistent flushes that pin and grow at the same time.
@@sourcecodex3189 or just by genetics online and make agar transfers 😭
@@ianplattner9930 agar transfers is Isolating the strain lol 😂
@@sourcecodex3189 First off Isolation is most commenly being refered to when using MSS because there is work to be done and it can take time and effort and clones and lots of plates to get the genetic up to full canopy flushes ect, or like i said you can by LC online with good genetics and just put it on agar if you want to save the genetic. If you are really using the term "isolation" while talking other than MSS its not hard at all and your statement becomes void lol.
@@ianplattner9930 First off there are many ways to isolate a strain and the current most popular on RUclips which is the platform we are commenting is transferring from agar to agar. So I’m still correct and you still look like an ass
Got a question about the fan. I've never grown mushrooms. Just been doing a bunch of homework on what to do and what works best for me. But the fan. I couldn't tell maybe I missed it. But is it blowing the air out of the tub or in?
Is there any way I can get clickable links to all the supplies needed for this project? Looking forward to making one!
I ran my first ever grow on your monotub setup and grew 1.25 ounces on the first run dry weight!! Thanks Willy and much love TTF!!!
How many quarts of spawn?
@@gregorsamsa1364 3 quarts
That’s really not a very great yield. I’m pretty bummed to read this lol
3 oz or more would've been a good first flush. This is what happens when you try to "automate" an already effectively automated system- diminished yields.
Automated failure
Very sad yield. Build one of these instead and do bags or straw logs instead.
I've never had the courage to graduate from pf tek. Now I do. Thanks for the pep talk!
you definitely educate and help. and entertain in the process. glad I tuned in.
If you know or want to learn a little electronics, you could use an Arduino to run the fans, misting and lights too. It has a built in timer. You can find code to copy and set it up pretty easy. Arduino has endless possibilities.
Off topic a little...cheap pressure cookers can be found at thrift stores
3:55 action starts
Love the video but the intro was super frustrating to sit through, I already know what the video is covering and everyone knows to subscribe/like in order to follow/support your content.
In the famous British words: “Get on with it.”
Otherwise thank you for taking the time to add you knowledge to vast database of the World Wide Web. It’s most helpful and your intuitive insights are gems now added to the collection of my knowledge.
Bravo.
Get over it its Willy You are lucky he is there for you .Apoligize please
@@patbloodysabbath8488 oh entitled and frail human ego, dost thou truly feel that your power is so great as to command me to do as thy will?
Not apologizing for a very mild comment I made regarding the honest expression of my experience with this video. Especially when I finished the comment with a compliment, a word of gratitude, and a Bravo.
You better watch how you talk in public because the internet protects here you from getting slapped for that kind of arrogance but in the real world people do not tolerate monarchial commands from some petty pauper like yourself.
Tread carefully with thy tongue, foul snake.
Dude, I absolutely love your content and how detailed you are. Thank you for the education.
Dude you've been so influential to me through my younger years I just wanted to say thank you
I learned from him a couple years ago. Glad he's still creating content.
Your video would be much better if only %10 was of you talking in frame, people wanna see you do stuff not flap your jaws no offense.
I liked what he had to say
@@marklange121 Not saying he should remove any content, he should just talk over the video with him doing things or put a pip window in the corner of himself. But i personally find it hard to watch someone talk when there are some many better ways to express the idea usually.
@its possible I agree because I'm a visual learner but its hard to really get everyone's learning points ig but you can do both with showing and talking.
Can’t take the beginning of those videos with so much talking
Good stuff is on Patreon.
No filtration for FAE or Gas Exchange holes? Seen so many use polyfil, is there a specific reason you don’t use anything?
Do you setup your fresh air fan to blow air into the tub or suck the air out of the tub? I couldn't really tell by the video. And is it the same with your walk in grow tent? I have both and am wondering how to setup my fan
Me too , any luck ?
Where are the links for the timers, monsoon and lights?
you find it?
Yeah.
The fan: www.acinfinity.com/quiet-usb-fans/
The Monsoon: www.petswarehouse.com/exo-terra-monsoon-multi-system-pt2493/?gclid=Cj0KCQiA-rj9BRCAARIsANB_4ABEVDxfqr9OdLE2iYADiLDbkhvtaEfb5QLNZU8Gvm1ry4kTs-wOJTkaAgVSEALw_wcB
The timer: www.homedepot.com/p/myTouchSmart-Simple-Set-Indoor-Plug-In-Digital-Timer-26892/207032979
The Link below for the exoterra mister is priced at $167...
@@720cinema8 u da goat
Just starting out thank you make it so much easier to the point in sharing what works for you
I just need to learn mycology but this guy just keep on going
Try looking up mycology , this is preparing an environment for fungi
He use to teach u mycology, but of course youtube took his channel down, basically everything i know about mycology is from this man or shoormy
@@auttoar1515not to disrespect but i learned more from other youtubers that get to the point of what they wanna teach
@@jacovandenberg213 oh i learned a shit ton on the pf tec from others, but his mono tubs are the best on youtube maybe even the internet
Better to use a fog machine that utilizes a humidity guage inside the tub rather than a mister.. when the fan comes on and the humidity drops, you can set the guage to come on when it humidity hits 70 or 75% then turns back off at 85-90% RH, wherever you want the guage turn turn on/off at, it can be at any RH you want..and it won't come on again until the fan blows out the CO2 3 or 4 times per day or it shouldn't
If you've got the right temps and correct sub depth and saturated at field capacity.. i use a pseudo casing with left over sub.
I haven't used automated in awhile, now I use 2x 2" inch holes down low on both of the long side right in line with my sub line at 3.5 inches so I'll put the holes at 4 for my 0.5 case. Then I'll put one on each of the narrow ends of the tub about as high as I can go, then I'll cover them with either a filter disc (once I introduce fruiting conditions at 80% colonization) or 2 layers of microtape after removing the masking tape that was on there to prevent FAE during colonization of my substrate. I don't even have to mist or fan, the humidity stays perfect and since it's a small room my HEPA filter inside cleans the air while also moving the air around to help out FAE, so It's set it and forget until harvest. I just keep and eye on the temp outside the tub, i like 70-72 in the room because that will mean it'll be 72-75 inside the tub, it's always 2-3 degrees warmer inside.
Biggest issue people run into is taking the lids off constantly which changes the humidity inside and it can never stay consistent, so it has to basically reset and rebuild the humidity which dries the cake out more and more each time, it lowers the temperature inside the tub by multiple degrees each time it's removed.. as long as you aren't getting those fuzzy feet that are trying to walk up the base of the mushroom thats short and fat like a chode, you're fine when it comes to FAE. I almost feel like people need to invest in a C02 reader, just to make them feel more at ease. Leave the lid on, just look at it through the sides and you'll know if there's any issues based off what the mycelium and/or mushrooms are telling you.. Another issue is over misting, people mist directly on the cake while there's pins, thats a good way to get aborts. If I do mist, I never mist the cake once there's pins and i try not to at all once after i put it into fruiting conditions because it retains so much moisture.. but, if i do, I always mist the sides and the lid and I make sure there's no big water droplets that will run down and drop on the mycelium/pins. The second flush I'll mist the sides and lid real well, then put the lid back on like the first flush.. the 3.5" sub depth with a 0.5" pseudo casing layer will provide plenty of water and nutrients for the mushrooms to pull from, it won't be getting low on moisture... yes it costs more in spawn and grain to do it, but if you only have 2-2.5 inches of sub then by the time it fully colonizes it's going to shrink about a half inch or more depending on the humidity you retained and with a fan you're going to lose more.. so do you want to lose money going towards good grain and sub, or spend less money and just not get the yields? Either way it's a loss, id rather get the big flushes cause honestly, a few grams pays for the extra materials. With a think cake the next flush will be even smaller as the cake shrinks and so on as it runs out of water and nutrients, that's why many people can't get a third flush even with soaking the cake... So it drastically limits your potential 2nd and 3rd flush, especially depending on the type of mushroom, some of them can suck up a lot of water lol. But with all that said, it always depends a lot on the genetics if they're high yielding or good for multiple flushes. Even if it's the same species or sub-species but with two different genetics, one might flush a really strong canopy once, then get progressively worse until its no longer worth it to maintain. While another might not be a solid canopy the first flush, but it has some pretty consistent flushes so it may weigh out better in the end but be a drastic difference in potency. All of that depends on the genetics...we can only give it the things it needs to be able to grow to it's full potential that it's genetics allows for, thats it. Which you'll learn what it likes and if you take a clone from the first run with a mushroom with solid genetics, the second run it'll be used to those conditions, the tub size, temps, moisture, the type of substrate and grain spawn, so the mycelium and mushroom adapts and starts thriving better if you repeat those same conditions. That doesn't mean you can get good results with poor conditions though, theres just variables that they're able to get used too.
That's what sucks about multispore...you've got no clue which of the genetics is going to germinate, no idea about any of it's traits like you can easily find out with LC or spawning from agar straight from the guy who isolated/cloned it. You may get an amazing one in a multispore, I've gotten pretty lucky before, sporeworks is always pretty solid, and then you can clone the best looking mushroom to agar or a slant to keep the genetics to work with in the future and keep cloning the different generations from there.. Or you'll get a multispore that germinated that turned out to be trash, either small yields but good potency (or small and weak, worst of both worlds), or like me the very first time, I had huge yields but literally zero potency and I mean zilch, 8 grams and not even a microdose. Back then I thought i did something wrong but i couldn't figure it out since the looked so healthy, i was pissed, but I finally realized it wasn't my fault... i did everything i was supposed to do and i grew a lot more than i expected and i could take what I learned moving forward, so its never a total waste as long as you gain experience in both what to do, aswell as not to do. I don't think that spore shop even exists anymore, I know I've heard nothing good about them but it's my fault they tricked me with a gimmick. Since I was new back then i saw they were selling a spore syringe with water/activated charcoal so it was solid black, it was to help prevent contams, which, maybe it did exactly what is said cause I didn't lose a single BRF cake, but man, did they ever put the wrong genetics inside... I went to sporeworks after that, best place for a multispore IMO. Now I get genetics by LC syringe or on Slants that I can store for long periods of time in the fridge to slow down colonization and transfer it to LC when needed... I've heard vaccum sealed and stored away in the fridge away from light they can last a couple years on slants, even a year or two in LC in the fridge that has been slowed down. I've even heard of people freezing colonized grain bags, slants, and LC, but I've never had the guts to try it. Maybe if I run into some not so good genetic material I'll freeze it in multiple mediums for 2-3 years vacuum sealed to prevent freezer burn, then try bringing to room temp slowly and then do a transfer from the slant or LC to a agar plate and then grain into some substrate to see if it begins to colonize, or if it continues colonizing the grain bag if it hadnt full colonized before freezing. Which I'll probably mark the growth with a sharpie just incase it does something weird like slowly grow on the surface or something while frozen
You can buy a hose splitter to do two tubs, but youll need to refill your fog machine up more often.. remember to remove the hose and machine every few days to steralize with alcohol.
The fan is great... and the awesome thing about the fogger, it'll come on any time it's needed without the fan if RH isn't where it needs to be. And it's not a mister, it's a legitimate fog just like when water evaporates and then falls back down. Just be careful if you point the hose upwards, you can get water drips so it'd be better to add it to the top straight out and fog will fill the whole tub equally and basically the cake will only absorb what it needs and there's water build up on the cake.
Is there a giveaway? Awesome vid although I wish there was more illustration, showing the drilling etc. More than talking but still very informative! A starting myco here about to fruit my spore and this is the most nervwracking part
Monsoon solo on amazon is 89$ where is it 40$??????
I paid 125😭
@@kingzach5000 Up to 300 now
@@dixondeep8229 damn try Petco
Do I need to use 2 nozzles or just 1 for the monsoon .. 64 litre monotub
Yo man, I just stumbled on your channel and find it very informative. But seriously man, editing. This video could seriously be under 5 mins.
Holy smokes yes
This is all of his videos. Seriously.
Stop hating. Some people don’t do well with the readers digest version. This way he caters to everyone. If you don’t wanna see it all just fast forward to the part you need to see.
@@justinely9073 he's not catering to everyone if the snappier students are bored off their nut, and constructive criticism isn't hate so stop diluting the word.
Nah this is good. A lot of people breeze through too fast. That's why I like his videos more than a lot of mycology videos .
Can you please shoot a good light for this set up im still really unclear as to what to get as far as lighting.
Same here my man
I don’t see your videos talking about lights on RUclips. I would love to learn about your thoughts on lighting for a monotub.
Not really needed in direct sunlight here and there would do it.
Wow the end of this video was the best God bless u
I’ve learned so much from you over the years Willy. You’re a wonderful soul Willy.
Hey ..
What about thé Heater ??
Willy, BY FAR, the BEST INFO OUT THERE, Thank you
Hey are the FAE holes and GE holes supposed to be covered in something like micropore tape? Or are the FAE holes supposed to be left open
Would have been nice if he showed us the thing fully assembled.
Left open
Yes FAE holes should be covered
@@repinsJ I’m still confused about the process of spawning to bulk. With BRF cakes you just leave them in the jars until they’re fully colonized. With monotubs, your grains must be fully colonized and then you introduce them to your bulk substrate. Then your bulk substrate has to fully colonize before moving to fruiting conditions. I look at this stage as being similar to birthing and dunking your BRF cakes. What should the mono tub look like before moving to fruiting conditions? Obviously the tub is much larger than a mason jar, so do you replicate the conditions of the mason jar (a closed system with small gas exchange holes) before starting the misting and fanning process?
I don't get it ...RH HOLES open or polyfil what about FAE HOLE open or polyfil?he never addresses that in video
I needed one of these all mine died when i was in hospital. Unfortunately they dont seem to be for sale anywhere and where they are there sold out. Ive bought a humidifier and a plant drip feed aystem instead together do you think theyll work?
This series is very helpful for me as I work 73 hr shifts each week. Hopefully this will make it possible for me to grow mushrooms anyway! Thank you!
How did it go ? I'm in a similar situation
@@nachospopthe3rd564 It worked out great! I am loving growing mushrooms! With the long shifts I definitely had to check it last thing before I left and first thing when I got home but I was so excited about it that was no problem anyway! lol Have fun!
@@cyndihull4322 sweet thanks for the feed back!!
Great suggestions for upping your game.
Is this automatic misting system better than using an automatic humidifying system? There are ultrasonic humidifiers for reptiles for around the same price that allow you to set a target humidity level instead misting based on repeated intervals and times.
Won't the drilled holes contaminate the environment? Since mushroom growing needs a sterile environment?
Gotta be honest this is painful to watch. This guy is like the rough draft of an essay that really needs to be edited. Tons of useful info surrounded by useless rambling.
That's the problem with "uppers" crazy smarts bound in painstakingly dry rambling. Absolutely great info, no disrespect or judgments intended, purely an observation.
U get use to it
Damn. what a douche thing to say. Just an observation.
@@trupyrodice4462 What makes you think he’s taking “uppers” besides rambling? Also I hope you don’t think shrooms are an “upper” lol? Also it’s not cool to assume someone’s taking any drug, that might just be their natural behavior
I have been watching at 1.5 but 2x is possible
Do I cover all the holes during fruiting with micropore?
I'll refer you to this mate where I got mine
delivered discreetly***¿¿¿
On Instagram¿
Healerbryan2…
This works great! While in colonization I taped everything up with painters tape then after four days the sub was 70% colonized. I then cased the sub with 50/50 mix and 6 days later I put in fruiting conditions. I did not start misting until day two of fruiting. You will see pins at this time possibly. once I put to fruiting I fan 3-6 times a day, 3 times auto from timer then 3 additional manually. on day two to day three I start the monsoon mister every eight hours and leave the automated set up and check on it once a day without having to do much at all. I used medical tape after removing the painters tape on the large holes during fruiting and left the small holes on the bottom uncovered. I have pins on day two of fruiting only fanning for the first day or two RH after fanning drops to 88 after a few minutes it's back to 93-95 RH temps remain around 76-78 love this set up. I can't wait to try Panaeolus Bisporus next
Bless you man. I'm not into the Bible or anything but I just wanted to say it. Cool stuff. Getting into it now myself.
Do you make a filter for the holes. I’ve seen other tubs have like Cotten or stuffing for a filter in the holes.
Ghetto tek = polyfill; any big box store in the craft area.
Pro tek = 0.2micron filters; lots of options to choose from. For this design in particular you could probably fit syringe filters in all those holes. The filters restrict the air flow and more holes may be preferable. Or, use a high pressure air pump like a nebulizer and push fresh clean air in, while pulling the old stale air out.
www.amazon.com/s?k=syringe+filters&ref=nb_sb_noss_1
I would advise doing your cycles opposite of how he describes in this video; first run the fan, then the mister. The moving air will dry things out a bit. It also more close replicates natural conditions, where the wind picks up and then the rain comes.
Best demonstration video on RUclips! Nicely done! Thank you 🙏🙏🙏
Hey Willy, I have quick question. I'm an amateur, can you explain to me why I would need FAE holes when you already have Gas exchange holes in the mix? I thought the FAE was a feature of the shotgun fruiting chamber and Gas exchange holes were traditionally for monotub tek? Thanks for your help.
Which time do you use. I bought the Indoor Digital MyTouch SMART and I can only program one time. Any instructions on how to program these???
Same question i need an answer for. you find out yet?
@Steve Trahanas I use a different timer that works great for the fan I can share the link 10 bucks
Nearpow makes a short cycle timer with dual outlets, where each outlet is programmable separately.
So happy I found this blessed channel. Thank you brother 🙏🏻
Do you cover your holes with miceopore tape or polyfil?
You can do both but polyfil would be preferable due to slightly more fae.
With the fans tho would that effect fae like say if u add a second fan? Making micropore better for the purpose?
What about reptile humidifiers over sprayers. Do see much difference?
What I have found, when using drill bits to make holes in plastic is NOT to use a drill (because it usually cracks), but take the drill bit and heat the end of it with a torch and MELT the hole in the plastic.
just run the drill bit in reverse first with the drill let the bit heat up then set the drill to lowest gear and go slow
Just buy a step drill or a hole saw kit. Twist drills suck for plastic
Thanks so much for this awesome video! And your kindness really shines through your videos!!
Personally, I’ve found that you really don’t need artificial light at all. If you’re going to use artificial light, you can fruit tubs perfectly fine using the light on the ceiling of a room, and even just with the natural light that comes in the window. You also only really need 4-6 hours of light a day, not 12. I’ve tested 12 hours vs 4-6 hours and the results were identical. So don’t waste money on electricity doing it for 12. Imo best bet is to use natural light. In the window or even just in the room. Super easy, no hassle.
Would you say that a clear lid is absolutely essential even of the tote is clear? I found the perfect tote for my grow and only opaque lids..
OmniClimHazard I don’t think the details matter lol mushrooms will grow pretty much anywhere I suppose. When I was growing I used clear lids but I doubt it matters.
@@huntercrainmusic Cool. Ill give it a whirl. Ive been a mushroom forager for over a decade and have gotten some of my best harvests from little to no light areas in the woods. I was just curious what all the fuss was about among homegrowing regarding the need for so much light. I think Ill do fine with a solid lid. ✌️
OmniClimHazard yeah the truth is there isn’t reason for any light at all. And if you do use light you need like. A TINY amount, for a very small amount of time per day. The ONLY benefit of this is to speed up the time it takes to begin fruiting. Once they pin, you no longer even need to do that. And if you leave them in complete darkness they will still fruit just fine, but will take a few extra days to start.
@@OmniClimHazard it shouldn't work, mushrooms grow towards light, they'll grow to the sides of your tub. If you want you can make it extremely compact inside the tub and have quarter inch holes all over it, and they should grow through those quarter inch holes.
The fan is on the outside of the lid, blowing air into the tub, correct? Also, where does the power cord for the mister go? Are there cables running through the gas exchange holes?
Hey willy where you get your masks. I know u said about it before but I don't remember what video it was in. N thank you
If you have a drill with a slower speed- use that, and if you switch it to reverse, it drills slower, melting the plastic and leaving cleaner holes without cracking. I love your FAE design! 👍
Your audio is to low. Please explain the FAE holes vs Gas Exchange holes?
Use captions
Soooo what about contam with those holes? I would grow nothing but mold in this tub. But then, I grow nothing but mold in every tub
I’ll edit your videos for free to save everyone all the unnecessary talking and over explaining, all your videos could be half the length at least. Still appreciate the effort and information you share but damn bro it’s exhausting
The over explaining is perfect for people that don't know very much about it, some of us have more knowledge with this, and others have no knowledge. The off topic stuff might be annoying but for people that have less understanding, I'm sure they really appreciate it.
@@trevormerivale6882 Nope, I don't know much and I still couldn't watch. Over explaining can easily be remedied with simply planning an Informational script for the video to go along with for fluidly giving information and efficiently progressing through the topic being explained. ...oh and to end the video summarize the main topics and important points to write down. I just went to another channel. (I didn't just complain, I gave a solution too, so don't yell at me.)
@@rjennings0142 that's fine but that doesn't mean it's not helping people out there. In life you can't please everyone all the time. You are more than welcome to watch a different video for the information, you obviously know that because that's what you did.
i think the same, a lot of explanations are too obvious
Does the fan blow in or out?
This video wins the You Guys Award for using the term "you guys" more than any other video on the internet.
😂😂😂
Congrats you guys
Make a video. Let's see how you do.
@@Emeighttwelve I have made several videos and posted them on my channel.
@@dcez1370 im talking about you actually making a video helping the community.
The best I’ve seen so far.
Good information
He said were gonna keep this video short and sweet then talks for literally 40 minutes seriously stop talking homie and tell us how to make it and what to do...
Lol
my thoughts exactly
I followed 55 perps who also did videos,on youtube on how to grow 3 years ago ,and WILLY is the only one who knows what is up.the others were short and impotent as a mule. He has videos where he takes you to a Target,Ace or Walmart and shows you what to buy saying not to buy the way over priced stuff that The Hip manufacturers mark up 900%,but the cheapest of the cheap and he says: "I am telling you that this is 1/10th the price and gets the job done. After hearing his videos I had some great large crops in my bedroom.
anyone has a better tutorial video?
@@RasMajnouni well if you read around on mycology boards on Reddit, Facebook, and the shroomery, you’ll realize he has a lot of non sense teks as well. The whole “slurry tek” and etc. just over complicating a simple process for very little gain when put into practical use. His Laminar flow hood tek that didn’t even include a prefilter so you’re pretty much just destroying your hepa, degrading it wayyyyy too fast. Just small details like that can be the difference between a Filter that lasts one year, and one that lasts 7 years. He has some good information but get an unbiased second opinion away from his fans in the RUclips comment section before you try anything tbh.
I've loved you since the first video I saw of yours years ago at least 3 or 4 years ago. You are amazing dude I mean that I'm a polymath much respect and love
Awesome video man! Thanks for the knowledge. Now, one question. Why a mister instead of a humidifier? Does it really matter? Keep spreading the love! One Love!
I too want to know.
Humidity should be high as fuck if your soil is moist in a tub that size...
@@validZander Thanks for trying to answer my question...I understand that...however, I wanna know why he chose a mister rather than a humidifier?? Tub size don't matter, at all, humidifiers are used in fruiting chambers bigger than this tub. I feel a humidifier would keep humidity higher than a mister hence the name HUMIDifier...but I'd imagine the fanning part would dissipate the humidity faster than fanning after a mist. Hold up. Maybe I just answered my own question!? Lmao!!
@@JradTHM but if the fan only kicks on for 60 seconds every 8 hours then the fogger/humidifier should keep it at the proper lvl the rest of the time
Thanks for the information. Do the Free Air Exchange holes or the Gas Exchange holes need to be covered in micropore tape (or cotton fill) to keep out contaminates?
Do you also put polyfill or micropore tape over each fae hole?
That’s what I want to know
Lot's of information one question would a fogger work as well ?,I'm thinking of getting one with a humidity controller.
Use a soldering iron to melt the hole, way easier than drilling
but that stinks and i have a drill
Says the guy that doesn't own or know how to operate a drill
@fibonacci DUDE TY
@@DaddyDayTraderLLC right, I have a soldering iron but not a drill...
I agree that sucks I have a drill and not a soldering iron
In the all-in-one bag method when you put the bag in the container what is that white powder stuff that is mixing with water it looks like that it is used for it to hydrate the mushrooms
yer a solid dude. gonna hit yer patreon. so many folks are depressed/down with the pandemic. i'm hoping micro dosing will help them out. all the best, brother.
Your a good man
Great video Wily..I wrote down the things I need but noticed the monsoon solo is $100..any cheaper options that'll work good.
It was dripping pretty bad also, but that can be easily fixed.
Love it man, I've been doing this for like 3 years except I use a muffin fan and a Dyson HEPA filter from a vaccum
What is a muffin fan?
What exact HEPA filter and fan do you use ?
Would you use a humidifier instead of misting system now the t3 cloud forge now?
Where do I get a timer that I can set for 60 seconds.?
Anything Amazon will. Just tell Alexa set a 1 min timer. Get an amazon echo
You mentioned using the mono tub for colonization, then take it into fruiting. So do you put the grain bags in the mono tub and keep it dark, or do you colonize in the tub with everything sealed up? Total newbe, ...I don't want to regret never trying these, and I'm not getting any younger. I want to be my own hero.
I bought the same timer you shown in the video and it doesn't do 3 times a day 8 hours perfectly inbetween like the monsoon does. You can only customize a on and off time for all 3 preseta in 1, you cant edit each individual preset like you explained. I bought the one from your link. If you could explain better how to set up the timer or explain exactly what one you are using to do 60 seconds on, for 3 times a day with 8 hours in between that would be great. I have a tub going and bought everything to find I cant sync my fans to the monsoon.
Looking for the same answer. I have the same timer no luck let me know if you found one that works
Any luck?
So we're not worried about contamination coming through the fans?
I think this is the same guy from Peru with the Boston accent that thought me how to make dmt
good point lmao
Was looking for this comment
Can't believe other people remember that lmao
It is. This man has literally taught me everything I know. But yeah “Peru” lol
Ah the good ol Peruvian chemist I love this guy
@Willy The monsoon solo is discontinued. Are there any other alternatives you can suggest please?
The 1" "circular drill bit", is called a Paddle bit the one you described would also work but entails a lot more care in its' use.
Or a forstner bit
Or a spade bit.
What he should have suggested was " cup saw " or " hole saw ".
@@ridethepace6005 Yes you can go up to 3" or 4" with them, separate saw bits of course.
@@jomammy7786 Not a forstner bit. You would most definitely not want to use a forstner bit for this application. Those are designed to be used in a drill press only for drilling flat-bottom holes in wood.
You forgot to link the products
That Gum Is Climbing Out of Your Mouth omg
He forget to do a lot
This cat thinks he’s the bees knees and Uber self important
The products are there.... highlight the links, do a google search. donzo.
Right, All this talking and doesn’t link the products 😑
@@solumefood I like that he didn't link it because that means this video isn't a commercial.
Holly Laird the purpose of this video is for us to follow his instructions 😂😂😂 how can we do that without knowing where to get the products. I don’t understand you lol
Noob here, do I need to use anything to cover or filter the 1” gas exchange holes? Or just leave them open? Thanks!
I found that when I heated the plastic with my heat gun before I drilled or cut it out with a razor blade. That it stopped cracking at all.
Put some tape where you're drilling helps too
You can use a soldering iron to cut your holes if you dont have a drill bit. Its slower, but less chances of cracking your tub.
to put an end to all the confusion regarding placement of fan (inside or out) that I have seen in the comments. Willy has placed it on the outside with the airflow directed into the tub. I base this comment on the frame in the video at, 23:51/39:06, where you can clearly see the fan and its grill on the same side of the lid as the, STERILITE, name. I like this setup and am in the process of assembling mine now. If I want to take off for a couple or more days then not to worry. Pluss it will help the little guys grow up strong and healthy knowing they live in a stable home not to mention it will cut down on those peski little contamination pinch points. See yall (way) out there; )...
Love this guy and I remember the Patron bottle in Peru lmao...but his best is the ACRB tek, it is perfect!!!