:7:34 Barrell is now too short. Darts haven't reached max velocity before leaving the blaster. Same with the higher spring. If you change ONE variable you affect all the others. OH and I love to see a ceda on the wall. Good video.
You mentioned you had to use a larger oring on the plunger. Maybe it was a bit too large and causing drag. I had similar issue with tuning a skewer to 250 and ended up adjusting my teflon tape multiple times to find the sweet spot.😊
@@sarahthompson9621 there's an ammount of vaccuum pressure created in a well sealed system when the breach is closed and the hole will release the pressure just before the breach seals to the pusher. The vaccuum pressure can lower performance & cause feeding issues
@@sarahthompson9621 It allow air to go in the plunger tube when bringing the Prime forward, preventing the dart to stick to the pusher by vacuum...messing with performance and reliability
Hello I'm getting a constant 180 fps with a 0.7g bamboo dartn 17.2cm brass barrel, and with the 1.7 spring, may I know where did you get the brass plunger tube and 14kg spring?
I can confirm your results. Same setup. But I sometimes have the problem that some darts get way below 120. does that happen to you too? Also I think a scar might help a lot with precision. Need to get one soon.
@@robmexx nope. Mine remain consistently above 170fps at that setup. I did swap out the pusher and plunger head o-rings though. It has roughly 10-15 second airseal.
I love how easy and clean the teardown is for this blaster! Great video!
Stock plunger tube with new spring?
I cant wait for mine to show up so I can swap a 12k firefly spring in there, and switch to a 14 inch TC barrel, hoping for a consistent 160-180!
:7:34 Barrell is now too short. Darts haven't reached max velocity before leaving the blaster. Same with the higher spring. If you change ONE variable you affect all the others. OH and I love to see a ceda on the wall. Good video.
I well know that, as I mention in the video that my barrel will be replaced by a SWIN 25-30 cm
Maybe drill a hole in the top of the pusher like on the Harrier & add a bit longer barrel & I'm sure it'll get over 200
Probably... TBH the ported one was not bad, but i'll drill the tip of my pusher to help. I might also slap a 25-30 CM Swin or ZWQ barrel on it
You mentioned you had to use a larger oring on the plunger. Maybe it was a bit too large and causing drag. I had similar issue with tuning a skewer to 250 and ended up adjusting my teflon tape multiple times to find the sweet spot.😊
What does a hole in the pusher do? Just curious cause I’ve seen people do this
@@sarahthompson9621 there's an ammount of vaccuum pressure created in a well sealed system when the breach is closed and the hole will release the pressure just before the breach seals to the pusher. The vaccuum pressure can lower performance & cause feeding issues
@@sarahthompson9621 It allow air to go in the plunger tube when bringing the Prime forward, preventing the dart to stick to the pusher by vacuum...messing with performance and reliability
Is that 1.8mm heavy spring?
?? it was ID as 14KG... but the Wire size look like 1.8
@@thatoldnerfguy oh okay.
Hello I'm getting a constant 180 fps with a 0.7g bamboo dartn 17.2cm brass barrel, and with the 1.7 spring, may I know where did you get the brass plunger tube and 14kg spring?
all link in the description... it was Biu Blaster
@thatoldnerfguy I would recommend the 17cm edge barrel which biu blasters sell, it has 2 orings to secure to the dart gate
@@JamesWatamii The plan is to go with a custom SWIN barrel... I might add the groove for the o-ring
I got around 179fps on the same upgrades but with a 19cm brass barrel using worker gen 2 HE.
Using the included suction cup darts, I got 220fps.
I can confirm your results. Same setup. But I sometimes have the problem that some darts get way below 120. does that happen to you too? Also I think a scar might help a lot with precision. Need to get one soon.
@@robmexx nope. Mine remain consistently above 170fps at that setup. I did swap out the pusher and plunger head o-rings though. It has roughly 10-15 second airseal.
@@adrianliew9288 could be that then. Im still running the original o-ring setup but planing to buy an upgraded kit.
1st comment! Love your videos!! :D
Thanks!!