1995 Toyota Celica Clutch Replacement
HTML-код
- Опубликовано: 25 авг 2024
- 1995 Toyota Celica Clutch Replacement.This is a very time involved job, a lot of parts have to be removed. But it will come out with out droping the rack & pinion back subframe. It took me almost 2 days to do. I had left the trans on the jack in the same position that it came out and it almost slid right back in.
This video was made as a demonstration how to repair things and should not be done with out the proper training and safety equipment. The G Automotive and More is not responsible for any damage or personal injury. Please if you don't have the ability to do these demonstrations, don't try and get a professional to do it for you.
You saved me about 4 hours of extra research. Thank you 🙏
These are a pain to, do not a lot of room. Thanks for watching
Legend, thanks for the video. Please endeavour to wear a particle dust mask when removing, cleaning and installing clutch components so as to protect your good health.
Cheers sir!
Thank you so much for this video. Just did a clutch etc change in my 95 ZR celica. You’re a life saver
I found this video really really handy! Thanks so much
As the owner of a 6g celica convertible, Thank you.
best video so far
Great thanks for watching
Hah! Friend just asked me to to a clutch in a 95 tercel in a driveway. After watching this, that's a hard f no.
That’s a 5efe not a bad job itself but deff a job where you should get paid for it
clutch is starting to go out on my 93 celica, might have to do this. Don't have the cash for a shop to do it, but I am fairly mechanically inclined. How far do you think I would have to lift the car to do this? I have a garage I can do it in but only a regular car jack/jack stands.
You are going to need to get the car pretty high to get the transmission out of your way. I would say minimum of 2 feet. Thanks for watching
I have a query. You didn't show us how the engine stays in place if you remove the 3 of 4 mounts. Do you use any engine support bar on top of the fenders, or do you just leave the engine hanging from the left mount?
At 3:28 you can see that I had a white upper support on top of the fenders. Thanks for watching
@@TheGAutomotiveAndMore Oh, you have right, my fault. Thanks for your reply.
I notice when I pull my clutch off... there was no pilot bearing but the kit came with pilot bearing... read some where that they do need to be install a pilot bearing for balance.... not sure what ya think...
If it doesn't have one I would not put it in.
Great!
Looking for the clutch fluid reservoir. Even the dealer didn't know where it was located !
I don't have the car here but is it not part of the brake master cylinder reservoir. A line that runs off it to the clutch master cylinder.
I know this video is old but if anyone is still watching the comments would approach to Only swap out the r rear motor mount (with the really long bolts) just involve removing of the exhaust and bolt on steering rack as shown?
Sorry its been to long and I can not remember.
I have a 2000 Toyota Celica GT and I'm swapping my clutch out. The toyota Manual states that the Match Marks on the flywheel should be lined up with the match marks on the clutch pressure plate. The problem is My stock flywheel doesn't seem to have any match marks, nor does the clutch pressure plate. I expected to see some recessed grooves or something. So, does this not matter? Not a single Celica clutch video on RUclips talks about match marks on the clutch and flywheel. The only place it seems to matter is within the Toyota Celica service manual.
I would match it up best possible.
I know this video is old
I live in a third world country that has like 4 celicas
So people don't know it
I want to replace my clutch
I have a st202 with the 3sge engine
What other Toyota cars that shares the same clutch and flywheel
Maybe it'll narrows my search for it
I heard people using a Camrys clutch and flywheel from the 2.2l model is it true?
Thank you very much in advance
I hope you understood what I was trying to say because my English is not that great as you can tell 😅
Sorry I do not know.
Is it possible to take the transmission out using an engine hoist?
The trans will not come out through the top. But I guess you could use it to lower it down. Thanks for watching
Do you have any tips for getting the gearbox back in? Really struggling to get it back in. The diff housing keeps hitting the subframe
Twist it up and get it in. It is a pain in the butt to get back In. The more people up have to help the better. Thanks for watching
What's the trick to getting the rear gearbox mount back in ? I've been having troubles for months ...cheers
A lot of wiggling around and make sure the clutch disc is alined. Thanks for watching
Do you remember by any chance the size of the ratchets you used to take the transmission apart? Going to a junkyard soon to swap a 94 Celica manual transmission to my 91 automatic Celica
Toyota's always use 10mm, 12mm, 14mm, 17mm, 19mm and 21mm. I think the axle nut is 32 mm but not sure. Thanks for watching.
The G Automotive And More thanks for your reply! Very informative video btw!
What torque
@@TheGAutomotiveAndMore 30mm on my scion xb and might need 12 or 6 point.
Do you know the OEM for the clutch system? I think it's AISIN, but I wanna make sure.
Probably is, but not sure. If you can get one that's what I would use. Thanks for watching
Do the clutch bolts take thread lock?
I think they had lock washers on them. Thanks for watching
It’s this the same for 95 tercel ?
No but should be very similar.
How do you get the linkages out?
They are near the firewall, I now they have pins that pull out but can't remember how they mount. Sorry. Thanks for watching
What torque specs did you use on the flywheel bolts?
Flywheel bolts are 88 Nm for the 2.2L engine. For the 1.8L engine it is 79 Nm. The presure plate bolts are 19 Nm for both. Thanks for watching
The G Automotive And More thank you for your quick response
Hi, i have the same celica, st202, can anyone please provide the part number of the Clutch disk and pressure plate? Thanks every one
Go look it up on Rock Auto. Thanks for watching
Great video. Looking at a used Celica needing a clutch, what was the total cost of this job.
I think it was about $1000.00
That's a reasonable number to factor in to the purchase price. Thank you
Your welcome. But what I would do also is call a local shop to get a price. Thank you for watching
I know this is an old comment but that seems really high as far as cost goes. I have a 97 and I paid less than 400 for a stage 4 clutch
trucker V I think his price included labor. Was yours just for the part?