ryobi 2900 psi model ry802900 pressure washer carburetor repair
HTML-код
- Опубликовано: 12 сен 2024
- carb
amzn.to/3stJLwx
acid
amzn.to/3go2BTe
todays t-shirt brought to you by YOUR NAME HERE
amzn.to/2RLsNcW
if this video helped you donate a buck or two to my GoFundMe account
www.gofundme.c...
The small engine guys are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com.
U saved me dude...great video
Great video!
Hey, great video! I had an ultrasonic jewelry cleaner that did a great job cleaning the bowl. They’re about $80 new on Amazon. Great for getting the crud out of lots of small stuff. I also bought your jewelry cleaner acid. Works great 👍
@@i_am_gumby205 yeah but this video is more for the everyday joe that just wants to clean his porch today. Not wait for an 80 dollar cleaner. A carb is only 20 bucks. These cleaners also dont work for my mower shop. I do about 30 carbs a day. I dont have time to wait. They do work if you have one though.
Followed the directions and used carburetor cleaner instead of acid and it worked!! Thanks!
Thank you for posting this video. This helped me a great deal. Hours away from being in the trash, running like new now.
Great job!
This is an excellent tutorial. I appreciate you sharing this!
Glad it helped!
Followed your directions and now it working and running pretty good. Thank you!
Great to hear!
Thanks! Couldn't have done it without you.
wow! thank you so much!!! glad i could help!
DUDE! Thank you! Best video. I absolutely appreciate the clarity and step by step!
Glad it helped!
Thank you sir!
Great step by step instructions.
Great video today was my first cleaning a pressure washer carb it would not start before I clean it after cleaning it worked fine thank you
Great job!
Thanks from San Juan PR; after I cleaned the carburetor with AutoZone's Carb Cleaner ($3.99) and an old toothbrush, it started with the first pull...
Great job!
awesome demonstration sir..
Many thanks
bought one of these used, wouldn't stay running with choke off, i took apart and cleaned and i don't have that longer tube at 7:54 at all. I checked, it's not there at all. What gives? Did somebody attempt to repair and leave that part out? Would that cause this condition of not running unless choke is on? The jet was completely blocked, i tried everything, carb cleaner wouldn't work and i don't have the acid. I had to go to harbor freight and pick up some tiny drill bits that worked perfectly to get a passage in there.
this will not run without the orifice tube anyways you need a new carb
Great video. Lots of rust debris in the carb fuel cup.
Thank you!
Thanks this helps a lot.
yep!
Where are you guys located? Definitely need help with my products.
i had a shop in fort lauderdale i sold it and now am 30 min east of gainsville fl
Awesome man thank you so much
No problem 👍
Great video! I went ahead and replaced the carb after the gasket expanded during cleaning disassembly. The new carb does the same thing. Shuts off after turning to run. Any other ideas?
Well done brother! This was excellent, so straightforward even I could follow it!
Glad it helped!
Great video, Picked up a couple of great new tricks. Thanks. The acid part was my favorite.
What is the acid ok to use on? You said not to use on brass or it will etch, but aren’t the jets brass. Will it not affect flow rate.
Yes but they are fine. Its where the needle valve goes. I try to keep it out of that.
How do you clean the pump if debris went in
i use spray oil. you may need to take it apart some as well. i usually dont its so cheap for a new pump just isnt worth my time. amzn.to/44aVeVN
RY802900
My pressure washer isn’t pumping with full pressure I’ve replaced the water hoses , air filter , gun and wand
Do you have any suggestions?
bad pump cheaper and easier than you think amzn.to/3ZnTuFr
I cleaned my carburetor as seen on your video but when I reattached the carburetor it leaks gas from the backside where the carburetor meets the backside…I tightened as much as I could but it still leaks gas…any thoughts????
same here, did you ever find out how to fix that ?
I thought I cleaned the carb on my pressure washer but I missed 2 areas to clean
i learned everything i know the hard way.
Still won’t start. Any ideas what else it could be?
3 things. spark compression fuel
Since almost everyone ends up with a dirty carburator after the first year, shouldn't they figure out a better way to keep the carburator clean? Is it even possible?
yep. electric.
Mine works fine on Choke position and shuts off on RUN position. I’m lost. Any ideas.??
clean the carb
I have the same problem, starts fine on choke then dies. Disassembled and cleaned the carb twice and havent found anything. Anywhere else i should check?
@@jessebarker8156 nope. Still 100 percent your carb. The main jet isnt clean enough yet sorry.
When I reattached the carburetor and open the gas valve it starts to leak gas on the backside of the carburetor….I tightened it a little bit more but it still leaks gas…any ideas on why?