Red Rubber Grease is totally compatible with DOT 4 fluids. It can be used to pack the dust boot to prevent ingress of salt and muck...unlike the Dot 4 fluid.
@@FastFixRUclips There is no need to pack the boot the boot will allow air to pass but not water or dirt. If you pack it it could make the boot pop off under air pressure.
@@FastFixRUclips You do NOT have to install the dust seal over the large dia. part of the piston first as you did here! Just install it into the indent on the piston where it is supposed to seat, and then push the piston into the bore all the way, and then push the rubber seal in with your fingers into the outer bore indent where it is supposed to seat, it goes in no problem at all! Then install the metal ring, and your done!
Didnt realize till like 6 hours ago calipers can be rebuilt, so im going to jump to it and do the same on my pickup. Beats paying a lot for new calipers, and just as easy to snap in a new piston as it is to replace a whole caliper. Good video!
I hear ya! I didn’t think about rebuilding until I got quoted the price for a new one. It’s definitely easier to buy rebuilt, but if you can rebuild for a fraction of the cost, why not? Just keep in mind it’s a bit tedious and will take some time 👍
Yup! But when you try to get a caliper rebuild kit(seal & dust boot) at a parts store they look puzzled & tell you caliper rebuild kits don't return anything on there computer search. They want to hose you by selling an overpriced rebuilt for 60$ or more. The kits are around 10$ & they don't make as much if they sold them.
Don't know if it's because I'm female or guys just like to assume I don't know anything. But my Volvo has very expensive parts and usually way too much money. $600 Canadian per caliper. I already replaced the back caliper and started seeing the videos for repairing the calipers. Now I'm hearing "you should never cheap out on parts" "it's incredibly dangerous to repair the calipers, just buy new ones" and garages actually getting angry at me for asking... This seems pretty simple and my calipers were in fine working condition before they were pressed in by the wrong tool, the wrong way.. the repair kits I found are only the gaskets. Should I replace the entire piston?
saved me after I destroyed the original and i did not want to ruin the new one going on/in thank you so much.I've watched it again just to refresh my brain rebuilt the left side and now the right side thanks again man !
This did save me. I rebuilt one rear caliper last year. Used a little pick to get the piston seal in. Pushing it with your fingers is much better, and a lot less select words.
@@FastFixRUclips no joke, I did the other rear, and giving up after an hour, pacing for about 15 minutes, I came back to this video and was done in maybe 5. I’m forever thankful you made this video lol
This video was soooooo helpful! Thank you so much for your content. This is great! I was about to purchase a new caliper. I was just tubing how easy it was to replace before I made the decision and this video showed me that I can just replace the piston for $9 on rock auto
DO NOT crimp the brake hose line this guy did! Unless you want more problems. Here's how to do it: Before you remove the brake line, disconnect the battery. Slightly depress the brake pedal. Slightly less than 1/2 inch after the pedal touches the pushrod and use something like a stick or dowel to hold it there. Now get to work. Doing this moves the piston past the inlet and return ports of the master cylinder so no fluid can leak down from the reservoirs. You'll just get a few drops out. If it's a metal line going in I clean and place the dust cap from the bleeder over the line if it's going to be apart for a while. You disconnect your battery because you probably don't want your brake lights on while you're working. DON'T CRIMP YOUR BRAKE HOSES KIDS!
Interesting advice as I was about to purchase some clamps so called supposedly for brake lines!! Well so much for that!!! I never liked the pink colour of the clamps anyway!! I'm not a pink guy!! (yeah right)
That's not a bad idea, I usually just keep a bolt,nut and 2 copper washers on hand that fit in the brake hose where the banjo bolt goes. Will give your method a go.
PLEASE don't crimp a rubber brake line. You can collapse the inner lining and then when you apply your brakes, the fluid travels down the brake line to the caliper as it should. However when you release the pedal, because the hose is internally collapsed it acts as a 1 way check valve, the fluid cannot return back through the hose, therefore the caliper remains seized. Another method to keep all the fluid from dripping from the brake hose when you remove it, is to press the brake pedal in about 1/2in with an extendable rod, or I've even used a brick. This means the brake lights will stay on, so you may want to disconnect the battery. (Remember your radio code) No more than 1/2in tho, that way the piston inside the master cylinder is moved from its resting state and mostly covers the holes leading down to the brake lines, therefore drastically slowing the drip of the fluid. Great vid, just wanted to pass that info forward.
That is an excellent tip. Hadn’t thought of that one. Figured the crimp method wasn’t ideal, but didn’t know of a work around either. Thanks for this it’s greatly appreciated.
You’re very welcome! I hope it goes well for you. Videos generally make projects appear easier than they are, however with patience and a little know-how this is a very doable job. 👍 Best of luck to you!
Im rebuilding a1990 Honda Prelude 4WS and everything under the hood and wheel wells is basically BLACK with thick grime. Good thing about being covered in 30 years of grime is once its cleaned off, you can see all the original metal treatments and coatings. I always thought the calipers were a grey color(online rebuilt calipers for sale are a dull grey due to being soaked in acid bath to remove said black grime but also removes any metal protection treatment) but in reality, they're a golden zinc color. I spent days gently cleaning and soaking in simple green. Lightly scrubbing with a brass wire brush. Lo and behold, the once velvet black calipers are now a greenish gold zinc color! I keep imaging how they looked new, contrasting off the silver rotors. I don't know if i should paint them with a high temp rotor paint tho just for future weather and temp proofing because, even tho the zinc coating looks great, i don't think it will hold up much longer and some areas have been scrubbed off almost completely. But man they look awesome tho! 30yo calipers that most ppl just toss out or replace for the dull grey "rebuilt" calipers(basically same exact calipers just acid bathed and rebuilt). Shoot i might just buy the online ones, paint them and save the zinc ones for posterity lol
Wow, I love this comment! I’m also a fan of the zinc color and if pressed, would keep it zinc for as long as possible. But you said it yourself, already worn off in areas and will soon giveaway to rust. I like the idea of keeping them around for posterity. Nice garage decoration 👍
Happend upon this video randomly glad to see people still out here rebuilding brake calipers. It's trial and error with the dust shield but once you have done a couple you can be in and out in like 20 min start to finish. $4.99-$12.99 vs $100-$300 well worth the little bit of effort to fix it. Me I rebuilt the whole thing. Replace the slide pin boots and bleeder valve as well. Literally cost me a total of $10-$20 per caliper and thats all they do in china with your core you give back then ship it back out to be sold as a remanufactured caliper.
Exactly right! So so much cheaper to do it this way and if you’ve got experience, you’re gonna be able to knock this out pretty quickly with little frustration. Most people are doing this for the first time, but hopefully after they completed once they’ll be able to do it again and again in the future and save a good amount of money. Great work and thanks for the comment!
Watched this in a rush after accidentally shooting out the last piston on my front Brembos while pushing all the others in. Definitely, definitely came in handy!!
An alternative way to get the boot back onto the piston is to seat the boot in its groove in the caliper, then slide the piston into the boot most of the way. Put a piece of 2 x 4 in front of the piston. Apply air from the back of the caliper and it should push the boot forward into its groove on the piston.
Hello! Yes, I forgot to film that part. The retaining ring/clip is installed last to retain the boot as you mentioned. There’s a machined groove that’s unmistakeable and where the ring fits into. 👍
Something that gets overlooked quite often when rebuilding a caliper because the vast majority of people don't know about this - is the seal that fits in the bore is tapered and needs to be installed so that it faces the correct direction. The seal is tapered so that the piston will slightly retract when there is no fluid pressure on the caliper. This keeps the pad from pushing into the rotor when the pedal is released and causing premature pad wear. People may not believe this is true but it is indeed a 100 percent verifiable fact
So does that mean the thicker end goes in first? I haven't noticed any tapering yet but that would also probably ease the installation of the piston when it's first pushed into place. I'm always slightly afraid that I somehow wringle and dislocate the ring upon insertion.
U can remove caliper but leave attached to car. Pess break peddle with pads removed. It should just pop out. Then gently clamp hose and undo banjo bolt.
Hello. BE advised that There is probably safe mode to operate on your rear brakes. I have an electric parking brake on my truck and I have to go through a few programming steps to enable “brake safety mode.” Fear is engaging the electronic brake on accident and losing a finger or two. Best of luck!
Hello. I’m not sure I’m understanding your question completely, but yes the seal should slide down the entire piston. It won’t cover the piston, just fits into the lip of the caliper. Hope that helps.
You put a board between the driver seat and brake pedal and move the seat forward to where the brake pedal is pressed like 1/2" forward and then stop. Then disconnect the battery and you shouldn't get brake fluid leak.
Hello. The metal ring secures the rubber boot to the caliper. Notice a groove machined into the cylinder near the outside. The boot goes in, then the ring goes in to secure the boot. Hope that helps. Thanks for the question and best of luck to you.
Short answer is yes, you will. The only other way I know of is to remove the caliper and depress the brake which will force out the piston. It’ll be messy… have a bucket on hand to catch the brake fluid. It’s highly corrosive to paint amongst other things. Best of luck!
Hello. Yep, that’s what I tell folks who don’t have access to compressed air. If it were me without compressed air, I’d probably forgo the rebuild and buy a reman. No thanks on the mess 😂 Thank you for the comment and suggestion 👍👍👍
I have a ripped boot on my caliper and might try a rebuild if possible to save some money. I dont have compressed air to push the piston out. Are there any other ways to get it out?
Hello. Yes, there are. You can always remove the pads and the caliper, depress the brake and get it out that way. You’ll spill fluid all over, however. Best of luck!
You could try, but guessing a hand pump will be difficult. You can disconnect the caliper and push the brakes to remove them, but it will be messy. Thanks for the question and best of luck.
Yes, sorry about that. Put it in at the very end. You’ll see the area where it’s supposed to go. There’s a groove machined into the cylinder near the top. It helps keep the boot in place. You just need to compress it slightly and place it in…not much to it. I hope this helps. Feel free to update the thread if you have issues. Thanks.
I didn’t do any measuring as I researched the part and knew it was correct for this caliper. To be safe, I suppose I should have, but it worked so I assume was gtg. Thanks for the comment 👍
Hello. To be honest, I do not remember. I’m sure there was a reason why I did that, but I suppose it’s also possible that I left in some footage that I shouldn’t have. Simply evaluate the situation when you go to do the repair and the answer should be self evident. Thanks for the question and have a good one!
I have a question: i have a 98 camry and today was doing my brakes and having taken the brake pads off, i accidently pressed my brakes too much and had one of the caliper came out too much. it's not going in no metter how much i try. one friend said the caliper is out of the housing and i need a new one. is there a way to get it in? or do i just need to buy a new one?
Hello. I assume you mean ‘piston’ when you say the ‘caliper’ came out. It should go back in. I bet the metal retainer ring is keeping it from seating back in the cylinder. So, remove the rubber boot and inspect the cylinder. If the retainer ring is still installed, remove it. The piston should go back in when you make sure nothing is blocking it. Hope this helps. Best of luck 👍
Hello. There have been some useful suggestions for people that don’t have air compressors so search the comments a little bit and hopefully you will find something useful. The only thing I’m aware of is leaving the caliper mounted after removing the brake disk. If you depress the brakes, the pistons will pop out of there, but so will all of the brake fluid so it’s pretty messy. I hope you figure something out! Thanks for commenting. Have a good one!
I had replaced the brake pads on my vehicle before but this time I wanted to remove the calipers clean them up and I couldn't figure out how to get the piston out. They were roofing a house across the street and I asked him if I could use a little air no problem I didn't know if it would work or not but what I was doing wasn't working an the compressed air shot that piston out of there like a bullet anyhow nobody got hit thank goodness. The reason I did it previously was because one of the seals had been pulled out and there was all kinds of dirt in there and that's why that particular caliper was getting stuck closed. No damage to the seal they were fines I'm re-overhauling them again right now.
Crimping the brake line is like bending a phone cord in one spot over and over and then expecting the inside to be fine and charge your phone. The pressure from clamping even once a brake line that’s starting to deteriorate inside can break the inside of the hose structure enough to cause the pressure to not flow right and your new caliper to cease from a lack of brake line pressure..
I have a small tear on the outside of my outer seal of one of my calipers. I'm not seeing any brake fluid come out of the caliper. Will that be a problem as far as brake caliper function or is it the inner seal which creates the seal, and the outer is just prevents dirt/dust from getting into the piston area?
Hello. Good question. The inner seal does keep the fluid in. The outer seal protects the cylinder from dirt, debris and brake dust. So, the caliper will function normally until too much debris gets in and starts to cause problems. They can last for quite some time with a torn outer seal, so my usual advice is to replace it when it starts to make noise. Hope this helps.
Once the outer seal is torn. Dirt and water will get inside and rust up the caliper around the inner seal. This will corrode and pit the piston which will then seize up. You can get seal and piston kits to refurbish calipers.
The replies here are correct: corrosion and seizure WILL happen. I reckon ALL the many calipers I've fixed or replaced, failed because either the piston outer seal was split or because the handbrake shaft was split - both causing corrosion then seizure. The repair kits with the seals are very cheap (~£6) and easy to fit.
Hello. If the leak is coming from the piston area of the caliper, then yes. Otherwise, you likely have a leak coming from the brake line or the bleed valve.
Good question. I’d say it’s not detrimental if you’re only using the carb cleaner for a limited time and making sure to wipe the surface dry right away. The cleaners are pretty harsh, but as long as you’re careful and don’t leave parts saturated, you should be okay. Thanks for the question.
Note that it's not the rubber piston sealing ring that causes the problem but of course the damaged dust cover that's responsible for letting water in and causing the piston to become rusty. The rust then causes the friction and may eventually lead tot leakage. So, if you notice a damaged dust cover then you can begin right away with your repair job as this will inevitably lead to the mentioned brake problems.
Hello. There are ways! A few good ideas in the comment section that I don’t remember off hand, but if push comes to shove, you can always use the brakes to pop them out. It will be messy!
How far did you get it in? Make sure you removed the bolt that holds the brake line on. I made that mistake and couldn’t understand why the piston would not seat completely. Let me know how it goes.
@@FastFixRUclips I did. I actually have the entire caliper off the car and cannot get it back in after setting it and using a c-clamp. I dnt wanna use a hammer but can I?
@@AngryAnR hello. Definitely don’t use a hammer. Something is wrong if you’re reaching for the hammer. I’ve been there, then regretted it. Ha. There must be something binding up the piston. Have you removed it then checked for obstructions? Look at the cylinder walls and make sure they’re smooth. If you see a gouge or something similar that probably means the piston didn’t go in square and roughed up the walls. Also, measure the piston and make sure it’s the right size. Could be that it’s too long and bottoming out. I wish I could see what’s happening and offer an precise solution, but unfortunately we can’t accomplish that through comment threads. If you can’t get it to seat you might have to bite the bullet and get a remanufactured one from the store. I’ve had to do that in the past and assume I’ll need to do it again at some point. Sometimes, it’s just necessary to quit and go for something you know will work. Sucks, but it happens. Best of luck and feel free to update this thread.
@@FastFixRUclips everything is ok. i dont get it at all. i had to break down and go get a replacement tho. i could not figure it out for the life of me. i even took it to a shop and they couldnt see why it wouldnt go in. just one of those things i guess. i truly appreciate all the feedback. until the next fix.......take care
I think I have a similar sound, on the pedal release tho, if I remember correctly. After discovering both front discs were scorching hot last week, I deattched the calipers from the discs and tested them by pressing and pumping them today. Front left seemed a bit harder to press in. Then, pumping the brakes to push both pistons out simmultaneously, the front left traveled less distance compared to the front right. Also, part of the dust boot on the front left is not stretching out evenly around the piston. So, I'll be doing the seal rebuild this week. Anyone thinking this is the reason for the brake/caliper drag on both discs? OT, I've learned that air in brake lines/master cylinder can cause a sinking pedal, but can it cause brake drags? @Fast Fix, did you replace the piston too? Did the rebuild eliminate the noise? Also, did you have any brake drag?
Hello. Yes, I replaced the piston and the seals. I didn’t have any brake drag...not sure what can cause that, but master cylinder malfunctions and sticking cylinders seem like likely causes. Best of luck!
Hello. The metal ring secures the boot to the caliper. Look on the outer edge of the cylinder. There will be a groove. That groove is where the ring goes. The ring is installed last right after you install the boot. In other words, the ring secures the boot to the caliper. Hope this helps.
@@FastFixRUclipsyour caption says to install the ring between the piston and the dust shield. Shouldn’t the ring sit on top of the shield (on the grove) so it’s between the shield and the caliper?
You can keep it attached to the caliper then depress the brakes. It’ll be a mess, but that’s another way. Prob a better alternative that I’m not aware of. Hope this helps
Hello. Everyday wear and tear is normally to blame. Although it might appear to be fine, if you’re seeing leaking fluid, best bet is to rebuild or replace. Especially if you can’t tell where the leak is coming from.
Hello. Dirt and road grime will work its way into the cylinder and eventually cause a failure. Or at minimum cause your breaks to make a lot of noise and not function as well. Thanks for the question.
The job is a bit more tricky than 1.5 rating. Anyone trying this need to know you may damge other components trying to fix this. I would rate this 2.5 out of 5. 😊
My technique when installing the piston and boot is to place a towel on my lap, place the caliper with the opening facing out ,then use both hands to guide the piston in. Your tummy acts like a back brace.
Hello. The metal ring holds the rubber dust shield in place. It will be the last thing you install. It fits in the groove machined near the lip of the cylinder. I know that didn’t get shown in the video. Sorry about that.
Hello. Yes, that piece of footage was regrettably left out. However, it is the last thing to install simply slip it over the boot into the groove. You can’t miss it. I hope everything works out! Thanks for commenting and have a great day.
Red Rubber Grease is totally compatible with DOT 4 fluids. It can be used to pack the dust boot to prevent ingress of salt and muck...unlike the Dot 4 fluid.
Hello. That’s good to know. I’ll definitely do that next time. Seems like that step would increase the life of the boot. Thanks!
@@FastFixRUclips There is no need to pack the boot the boot will allow air to pass but not water or dirt. If you pack it it could make the boot pop off under air pressure.
@@FastFixRUclips You do NOT have to install the dust seal over the large dia. part of the piston first as you did here! Just install it into the indent on the piston where it is supposed to seat, and then push the piston into the bore all the way, and then push the rubber seal in with your fingers into the outer bore indent where it is supposed to seat, it goes in no problem at all! Then install the metal ring, and your done!
😅@@retydown7521
@@kennyh5083: That’s what I did intuitively and it was much easier your way. 😃👍
You saved me 282 dollars. Thank you. You are the man!
You’re welcome! Glad this helped save the money! Comment appreciated 👍
That piston boost is the hardest things for me in the past but after watching this videos I got an idea. Thank
You’re welcome!
Didnt realize till like 6 hours ago calipers can be rebuilt, so im going to jump to it and do the same on my pickup. Beats paying a lot for new calipers, and just as easy to snap in a new piston as it is to replace a whole caliper. Good video!
I hear ya! I didn’t think about rebuilding until I got quoted the price for a new one. It’s definitely easier to buy rebuilt, but if you can rebuild for a fraction of the cost, why not? Just keep in mind it’s a bit tedious and will take some time 👍
Yup! But when you try to get a caliper rebuild kit(seal & dust boot) at a parts store they look puzzled & tell you caliper rebuild kits don't return anything on there computer search. They want to hose you by selling an overpriced rebuilt for 60$ or more. The kits are around 10$ & they don't make as much if they sold them.
Don't know if it's because I'm female or guys just like to assume I don't know anything. But my Volvo has very expensive parts and usually way too much money. $600 Canadian per caliper. I already replaced the back caliper and started seeing the videos for repairing the calipers. Now I'm hearing "you should never cheap out on parts" "it's incredibly dangerous to repair the calipers, just buy new ones" and garages actually getting angry at me for asking... This seems pretty simple and my calipers were in fine working condition before they were pressed in by the wrong tool, the wrong way.. the repair kits I found are only the gaskets. Should I replace the entire piston?
saved me after I destroyed the original and i did not want to ruin the new one going on/in thank you so much.I've watched it again just to refresh my brain rebuilt the left side and now the right side thanks again man !
You’re very welcome! Glad this helped 👍
Just did my 1st caliper rebuild thanks to your video it was very helpful.
Great to hear! Thanks for commenting 👍
This did save me. I rebuilt one rear caliper last year. Used a little pick to get the piston seal in. Pushing it with your fingers is much better, and a lot less select words.
Hahaha, glad this helped! Yes, select words used in many cases 😂😂😂
@@FastFixRUclips no joke, I did the other rear, and giving up after an hour, pacing for about 15 minutes, I came back to this video and was done in maybe 5. I’m forever thankful you made this video lol
This video was soooooo helpful! Thank you so much for your content. This is great! I was about to purchase a new caliper. I was just tubing how easy it was to replace before I made the decision and this video showed me that I can just replace the piston for $9 on rock auto
DO NOT crimp the brake hose line this guy did! Unless you want more problems.
Here's how to do it:
Before you remove the brake line, disconnect the battery. Slightly depress the brake pedal. Slightly less than 1/2 inch after the pedal touches the pushrod and use something like a stick or dowel to hold it there. Now get to work.
Doing this moves the piston past the inlet and return ports of the master cylinder so no fluid can leak down from the reservoirs. You'll just get a few drops out. If it's a metal line going in I clean and place the dust cap from the bleeder over the line if it's going to be apart for a while. You disconnect your battery because you probably don't want your brake lights on while you're working.
DON'T CRIMP YOUR BRAKE HOSES KIDS!
☝️ this!
or crimp it, replace pistons and replace the hoses for brand new ones. xD
Interesting advice as I was about to purchase some clamps so called supposedly for brake lines!! Well so much for that!!! I never liked the pink colour of the clamps anyway!! I'm not a pink guy!! (yeah right)
Thx . I really didn't want to crimp. Tried it your way and it worked
That's not a bad idea, I usually just keep a bolt,nut and 2 copper washers on hand that fit in the brake hose where the banjo bolt goes. Will give your method a go.
PLEASE don't crimp a rubber brake line. You can collapse the inner lining and then when you apply your brakes, the fluid travels down the brake line to the caliper as it should. However when you release the pedal, because the hose is internally collapsed it acts as a 1 way check valve, the fluid cannot return back through the hose, therefore the caliper remains seized. Another method to keep all the fluid from dripping from the brake hose when you remove it, is to press the brake pedal in about 1/2in with an extendable rod, or I've even used a brick. This means the brake lights will stay on, so you may want to disconnect the battery. (Remember your radio code) No more than 1/2in tho, that way the piston inside the master cylinder is moved from its resting state and mostly covers the holes leading down to the brake lines, therefore drastically slowing the drip of the fluid.
Great vid, just wanted to pass that info forward.
That is an excellent tip. Hadn’t thought of that one. Figured the crimp method wasn’t ideal, but didn’t know of a work around either. Thanks for this it’s greatly appreciated.
Interesting. I've seen a lot of pro mechanics do it and no warnings like this.
I heard the same thing about internal collapse. Not sure if it's true but I don't take any chances.
is there a better way?
@@djfukno4770 I stick a compressible foam ear plug into the end of soft lines and so far it hasn't done me dirty.
Never have done this before but saw your video made me feel real good about the project that I'm about to have to do just wanted to say thanks
You’re very welcome! I hope it goes well for you. Videos generally make projects appear easier than they are, however with patience and a little know-how this is a very doable job. 👍 Best of luck to you!
Im rebuilding a1990 Honda Prelude 4WS and everything under the hood and wheel wells is basically BLACK with thick grime. Good thing about being covered in 30 years of grime is once its cleaned off, you can see all the original metal treatments and coatings. I always thought the calipers were a grey color(online rebuilt calipers for sale are a dull grey due to being soaked in acid bath to remove said black grime but also removes any metal protection treatment) but in reality, they're a golden zinc color. I spent days gently cleaning and soaking in simple green. Lightly scrubbing with a brass wire brush. Lo and behold, the once velvet black calipers are now a greenish gold zinc color! I keep imaging how they looked new, contrasting off the silver rotors. I don't know if i should paint them with a high temp rotor paint tho just for future weather and temp proofing because, even tho the zinc coating looks great, i don't think it will hold up much longer and some areas have been scrubbed off almost completely. But man they look awesome tho! 30yo calipers that most ppl just toss out or replace for the dull grey "rebuilt" calipers(basically same exact calipers just acid bathed and rebuilt). Shoot i might just buy the online ones, paint them and save the zinc ones for posterity lol
Wow, I love this comment! I’m also a fan of the zinc color and if pressed, would keep it zinc for as long as possible. But you said it yourself, already worn off in areas and will soon giveaway to rust. I like the idea of keeping them around for posterity. Nice garage decoration 👍
Happend upon this video randomly glad to see people still out here rebuilding brake calipers. It's trial and error with the dust shield but once you have done a couple you can be in and out in like 20 min start to finish. $4.99-$12.99 vs $100-$300 well worth the little bit of effort to fix it. Me I rebuilt the whole thing. Replace the slide pin boots and bleeder valve as well. Literally cost me a total of $10-$20 per caliper and thats all they do in china with your core you give back then ship it back out to be sold as a remanufactured caliper.
Exactly right! So so much cheaper to do it this way and if you’ve got experience, you’re gonna be able to knock this out pretty quickly with little frustration. Most people are doing this for the first time, but hopefully after they completed once they’ll be able to do it again and again in the future and save a good amount of money. Great work and thanks for the comment!
Watched this in a rush after accidentally shooting out the last piston on my front Brembos while pushing all the others in. Definitely, definitely came in handy!!
Glad to hear that! Thanks for the comment 👍👍👍
This is what YT should be!! Thanks 💪🏾
EXCELLENT VIDEO! Great camera work and outstanding method thank you so much!!
You're very welcome!
Just don't crimp off the hose like this guy did. FAIL!
An alternative way to get the boot back onto the piston is to seat the boot in its groove in the caliper, then slide the piston into the boot most of the way. Put a piece of 2 x 4 in front of the piston. Apply air from the back of the caliper and it should push the boot forward into its groove on the piston.
Oh nice, that’s a good tip! Much appreciated. Will try that next time if I have to do this again. Thanks 👍
Thanks brother
Just knocked it out doing this method took 30 seconds thanks for the tip
isnt there a retaining clip for the caliper boot?
Hello! Yes, I forgot to film that part. The retaining ring/clip is installed last to retain the boot as you mentioned. There’s a machined groove that’s unmistakeable and where the ring fits into. 👍
EXCELLENT tutorial 😃👍 Saved me alot of hassle and money $$
Had mine apart with new seals to put in and could figure out how to get seal and piston in . .big thanks mate from Ausieland
You’re welcome my Australian friend! Happy to see this video crossing oceans 🌏🇦🇺 and I’ll throw a roo in for good measure 🦘. Cheers!
Something that gets overlooked quite often when rebuilding a caliper because the vast majority of people don't know about this - is the seal that fits in the bore is tapered and needs to be installed so that it faces the correct direction. The seal is tapered so that the piston will slightly retract when there is no fluid pressure on the caliper. This keeps the pad from pushing into the rotor when the pedal is released and causing premature pad wear. People may not believe this is true but it is indeed a 100 percent verifiable fact
Hello. Great comment! Thank you for sharing 👍👍👍
So does that mean the thicker end goes in first? I haven't noticed any tapering yet but that would also probably ease the installation of the piston when it's first pushed into place. I'm always slightly afraid that I somehow wringle and dislocate the ring upon insertion.
Is there a mark on the seal to show which way faces out?
Great video 🎉
What size C-clamp was that?
I’m glad I watched it all before I commented bc I seen the Zerk fitting in and wondered if that was right.
Yes sir!
good video, most video not show how to take out piston, thanks, good,
You bet!
U can remove caliper but leave attached to car. Pess break peddle with pads removed. It should just pop out. Then gently clamp hose and undo banjo bolt.
☝️exactly
You just saved me a lot of money! Thank you!
Hello. Great to hear that! I appreciate the comment 👍
Mine is doing that too on my 06 Civic. Thanks for the video!
You bet! I appreciate the comment 👍
Good video, I have a electric parking brake on the Acura with a ripped boot, gonna have to find out how that comes apart pretty soon.
Hello. BE advised that There is probably safe mode to operate on your rear brakes. I have an electric parking brake on my truck and I have to go through a few programming steps to enable “brake safety mode.” Fear is engaging the electronic brake on accident and losing a finger or two. Best of luck!
You just made my day! Thank you 👍
Glad to hear that!
Hey there can you please show us how to disassemble rear caliper for Cadillac dts
If you don't have an air compressor, can you use a slide hammer to pull the piston out?
Put a small wooden block, about 1.25in in the caliper and depress the brake pedal about 5-10 times til it is pushed out .
What he said!👆
Does the seal have to cover the whole piston? I can’t seem to keep the seal over the rear of the piston when I’m pushing it in
Hello. I’m not sure I’m understanding your question completely, but yes the seal should slide down the entire piston. It won’t cover the piston, just fits into the lip of the caliper. Hope that helps.
Smart very informative great video
You put a board between the driver seat and brake pedal and move the seat forward to where the brake pedal is pressed like 1/2" forward and then stop. Then disconnect the battery and you shouldn't get brake fluid leak.
Great idea! 👍👍👍
Where does the metal ring go? On top of the rubber boot?
Hello. The metal ring secures the rubber boot to the caliper. Notice a groove machined into the cylinder near the outside. The boot goes in, then the ring goes in to secure the boot. Hope that helps. Thanks for the question and best of luck to you.
But I don't have an air compressor. Am i going to have trouble getting the piston out?
Short answer is yes, you will. The only other way I know of is to remove the caliper and depress the brake which will force out the piston. It’ll be messy… have a bucket on hand to catch the brake fluid. It’s highly corrosive to paint amongst other things. Best of luck!
Hi, is it possible to replace only the dust boot without removing piston?
Unfortunately, no it’s not.
That piston appears new. You didn't say if you replaced the piston or if you cleaned up the piston that you pulled out.
Hello. It was replaced.
How do you get the piston out if you don’t have compressed air?
You could keep it attached to the brake line, remove the caliper from the disc, and depress the brake. Will be messy, but a way.
no need for an air compressor, you can do it with the brake pedal before disconnecting the brake line...though it is a bit messy that way.
Hello. Yep, that’s what I tell folks who don’t have access to compressed air. If it were me without compressed air, I’d probably forgo the rebuild and buy a reman. No thanks on the mess 😂 Thank you for the comment and suggestion 👍👍👍
Very informative
Glad it was helpful!
I have a ripped boot on my caliper and might try a rebuild if possible to save some money. I dont have compressed air to push the piston out. Are there any other ways to get it out?
Hello. Yes, there are. You can always remove the pads and the caliper, depress the brake and get it out that way. You’ll spill fluid all over, however. Best of luck!
any other ways with a air pump.. is hand pump possible ?
You could try, but guessing a hand pump will be difficult. You can disconnect the caliper and push the brakes to remove them, but it will be messy. Thanks for the question and best of luck.
det är mycket bra jobb och fixar mycket lättare
Glad to hear that! Thanks for the comment 👍
Thanks for sharing
You bet! Thanks for leaving a comment 👍👍👍
nice work
Thanks! Appreciate you taking the time to comment 👍👍👍
Great video!
when do u put the metal ring back? Any detail appreciated
Yes, sorry about that. Put it in at the very end. You’ll see the area where it’s supposed to go. There’s a groove machined into the cylinder near the top. It helps keep the boot in place. You just need to compress it slightly and place it in…not much to it. I hope this helps. Feel free to update the thread if you have issues. Thanks.
@@FastFixRUclips Ty
How much time did it take you per caliber to eject’0 piston, clean re-install piston. 10-15 minutes per caliber?
It’s hard to say because I was filming everything. I’d say this is easy a several hour project.
What is missing in the video is pre-fitting of the piston, what it looks like and its tolerance like when it fit into the bore. Thanks!
I didn’t do any measuring as I researched the part and knew it was correct for this caliper. To be safe, I suppose I should have, but it worked so I assume was gtg. Thanks for the comment 👍
Why diid you losen the caliper bracket bolts? You dont need to remove the bracket to remove the caliper do you?
Hello. To be honest, I do not remember. I’m sure there was a reason why I did that, but I suppose it’s also possible that I left in some footage that I shouldn’t have. Simply evaluate the situation when you go to do the repair and the answer should be self evident. Thanks for the question and have a good one!
I have a question: i have a 98 camry and today was doing my brakes and having taken the brake pads off, i accidently pressed my brakes too much and had one of the caliper came out too much. it's not going in no metter how much i try. one friend said the caliper is out of the housing and i need a new one. is there a way to get it in? or do i just need to buy a new one?
Hello. I assume you mean ‘piston’ when you say the ‘caliper’ came out. It should go back in. I bet the metal retainer ring is keeping it from seating back in the cylinder. So, remove the rubber boot and inspect the cylinder. If the retainer ring is still installed, remove it. The piston should go back in when you make sure nothing is blocking it. Hope this helps. Best of luck 👍
@@FastFixRUclips can you make a vid on this
I got the same problem
No Castrol red rubber grease on piston????
Use it if ya got it!
For the people that dont have compressed air whats the other method of removing the piston?
Hello. There have been some useful suggestions for people that don’t have air compressors so search the comments a little bit and hopefully you will find something useful. The only thing I’m aware of is leaving the caliper mounted after removing the brake disk. If you depress the brakes, the pistons will pop out of there, but so will all of the brake fluid so it’s pretty messy. I hope you figure something out! Thanks for commenting. Have a good one!
@@FastFixRUclipscan I put back In no problem or is there something stopping me cuz I can’t get it to compress with c clamp
can you just use brake fluid from the car pedal to pucjh it
Correct! Just a little messy, but you gotta do what ya gotta do 👍
You just taught me somethin I will always know how to do now man subscribing hope you do well and thank you
You bet! And you’re welcome. Thanks!
I had replaced the brake pads on my vehicle before but this time I wanted to remove the calipers clean them up and I couldn't figure out how to get the piston out. They were roofing a house across the street and I asked him if I could use a little air no problem I didn't know if it would work or not but what I was doing wasn't working an the compressed air shot that piston out of there like a bullet anyhow nobody got hit thank goodness. The reason I did it previously was because one of the seals had been pulled out and there was all kinds of dirt in there and that's why that particular caliper was getting stuck closed. No damage to the seal they were fines I'm re-overhauling them again right now.
Sounds like a close call! Had a guy comment here who said he broke his thumb doing this! Ouch…
Nice vid, good luck
Thanks 👍
Is it the same way with Camry 2000,4cyl??thx
Yes, more or less should be the same
UERY HELPFULL VIDEO
Glad this helped! Thanks for the comment 👍
Muchas gracias señorón Dios lo bendiga feliz noches me llamo Mynor soy de Guatmala
Gracias por ver mis videos, que bueno que te ayudo!
Nice job thanks for the video!
No problem! Thanks for the comment.
Crimping the brake line is like bending a phone cord in one spot over and over and then expecting the inside to be fine and charge your phone. The pressure from clamping even once a brake line that’s starting to deteriorate inside can break the inside of the hose structure enough to cause the pressure to not flow right and your new caliper to cease from a lack of brake line pressure..
Yes, I agree with you. Wasn’t optimal…
I have a small tear on the outside of my outer seal of one of my calipers. I'm not seeing any brake fluid come out of the caliper. Will that be a problem as far as brake caliper function or is it the inner seal which creates the seal, and the outer is just prevents dirt/dust from getting into the piston area?
Hello. Good question. The inner seal does keep the fluid in. The outer seal protects the cylinder from dirt, debris and brake dust. So, the caliper will function normally until too much debris gets in and starts to cause problems. They can last for quite some time with a torn outer seal, so my usual advice is to replace it when it starts to make noise. Hope this helps.
Once the outer seal is torn. Dirt and water will get inside and rust up the caliper around the inner seal. This will corrode and pit the piston which will then seize up. You can get seal and piston kits to refurbish calipers.
Piston will rust if the outer seal is damaged. Rust will stop the inner seal from working properly and piston wont retract
The replies here are correct: corrosion and seizure WILL happen. I reckon ALL the many calipers I've fixed or replaced, failed because either the piston outer seal was split or because the handbrake shaft was split - both causing corrosion then seizure. The repair kits with the seals are very cheap (~£6) and easy to fit.
Will this fix a leak coming from the caliper?
Hello. If the leak is coming from the piston area of the caliper, then yes. Otherwise, you likely have a leak coming from the brake line or the bleed valve.
Thank you sir!
You’re welcome!
I’ve heard it is bad to put anything but brake fluid in the caliper or on the piston. but you used carb cleaner? just wasn’t sure thanks
Good question. I’d say it’s not detrimental if you’re only using the carb cleaner for a limited time and making sure to wipe the surface dry right away. The cleaners are pretty harsh, but as long as you’re careful and don’t leave parts saturated, you should be okay. Thanks for the question.
I noticed I had a tear in my piston dust boot, can I just pump the brake pedal to pop out the piston from the caliper? I don't have an air compressor.
Hello. Yes, you can do that, but brake fluid will be all over the place. if you go that route, have many towels or rags down to catch the fluid.
Please where ti buy the part like piston Seal for the caliper. Please please. Thanks
Sorry, I don’t remember which site I used. You’ll just have to Google it.
Note that it's not the rubber piston sealing ring that causes the problem but of course the damaged dust cover that's responsible for letting water in and causing the piston to become rusty. The rust then causes the friction and may eventually lead tot leakage.
So, if you notice a damaged dust cover then you can begin right away with your repair job as this will inevitably lead to the mentioned brake problems.
Correct! 👍👍👍
Did you replace the caliper piston or did you just polish it up? Looks new
Hello. I replaced the piston, although I could’ve probably reused the old one. Thanks for the question 👍
I dont have air compresssor ,what shall I do
Hello. There are ways! A few good ideas in the comment section that I don’t remember off hand, but if push comes to shove, you can always use the brakes to pop them out. It will be messy!
Everything worked but even with a c clamp And compression tool, it will not go all the way in. What am I doing wrong?
How far did you get it in? Make sure you removed the bolt that holds the brake line on. I made that mistake and couldn’t understand why the piston would not seat completely. Let me know how it goes.
@@FastFixRUclips I did. I actually have the entire caliper off the car and cannot get it back in after setting it and using a c-clamp. I dnt wanna use a hammer but can I?
@@AngryAnR hello. Definitely don’t use a hammer. Something is wrong if you’re reaching for the hammer. I’ve been there, then regretted it. Ha. There must be something binding up the piston. Have you removed it then checked for obstructions? Look at the cylinder walls and make sure they’re smooth. If you see a gouge or something similar that probably means the piston didn’t go in square and roughed up the walls. Also, measure the piston and make sure it’s the right size. Could be that it’s too long and bottoming out. I wish I could see what’s happening and offer an precise solution, but unfortunately we can’t accomplish that through comment threads. If you can’t get it to seat you might have to bite the bullet and get a remanufactured one from the store. I’ve had to do that in the past and assume I’ll need to do it again at some point. Sometimes, it’s just necessary to quit and go for something you know will work. Sucks, but it happens. Best of luck and feel free to update this thread.
@@FastFixRUclips everything is ok. i dont get it at all. i had to break down and go get a replacement tho. i could not figure it out for the life of me. i even took it to a shop and they couldnt see why it wouldnt go in. just one of those things i guess. i truly appreciate all the feedback. until the next fix.......take care
Brilliant.My mechanic say you can,t remove pistons on modern cars.
I’m unsure if that’s true, but it seems like it’s not true 🤷♂️
😂
my piston not out with compressor pressure, stuck,, only with pedal push,
Sounds like a good time to replace the caliper! You may have a worn cylinder or piston.
Dont you need to grease the piston or something?
No, don’t use grease. It can gum it up and potentially cause problem. Use DOT fluid only.
Why the whole caliper is brush and clean ,in many of the videos of other mechanics the don't clean the parts
Dirty on the outside and clean on the inside is okay 👍👍👍
How about condition of the piston
Hello. It had corrosion and wear due to the broken seal.
@@FastFixRUclips I'm doing the same thing
I think I have a similar sound, on the pedal release tho, if I remember correctly. After discovering both front discs were scorching hot last week, I deattched the calipers from the discs and tested them by pressing and pumping them today. Front left seemed a bit harder to press in. Then, pumping the brakes to push both pistons out simmultaneously, the front left traveled less distance compared to the front right. Also, part of the dust boot on the front left is not stretching out evenly around the piston. So, I'll be doing the seal rebuild this week. Anyone thinking this is the reason for the brake/caliper drag on both discs? OT, I've learned that air in brake lines/master cylinder can cause a sinking pedal, but can it cause brake drags? @Fast Fix, did you replace the piston too? Did the rebuild eliminate the noise? Also, did you have any brake drag?
Hello. Yes, I replaced the piston and the seals. I didn’t have any brake drag...not sure what can cause that, but master cylinder malfunctions and sticking cylinders seem like likely causes. Best of luck!
I here same noise on front brakes release like a bad door open
This helped me move past my divorce with my third husbando Nathaniel💂🏻♀️
Same
Why didn't you show the metal ring? That is the hardest part that I try to figure out now...
Hello. The metal ring secures the boot to the caliper. Look on the outer edge of the cylinder. There will be a groove. That groove is where the ring goes. The ring is installed last right after you install the boot. In other words, the ring secures the boot to the caliper. Hope this helps.
@@FastFixRUclipsyour caption says to install the ring between the piston and the dust shield. Shouldn’t the ring sit on top of the shield (on the grove) so it’s between the shield and the caliper?
Air? What if you don't have a compressor to put air?
You can keep it attached to the caliper then depress the brakes. It’ll be a mess, but that’s another way. Prob a better alternative that I’m not aware of. Hope this helps
@@FastFixRUclips the other alternative is buy it brand new and save all king of pain
Yep, agree!
I would suggest cleaning the caliper housing before rebuilding , chemical and wire wheel. All it would take is some rust to destroy that new assembly
Good tip 👍
My 29 year old square seal looks fine does anyone know why it was leaking?😢
Hello. Everyday wear and tear is normally to blame. Although it might appear to be fine, if you’re seeing leaking fluid, best bet is to rebuild or replace. Especially if you can’t tell where the leak is coming from.
@@FastFixRUclips I put in a new 1 no more leaks I checked it for days all the lakes are gone....
Thank you sir... Seriously.
You’re welcome! 👍
I use a plastic fork to get the old oring out so it can't scratch the bore.
Wise move!
Were did you find parts ?
Hello. I got these from carparts.com. Sorry, I don’t have any links or part numbers. Thanks for the question.
Thanks
You’re welcome!
I'm almost convinced you set the dust cover the other way around.
Hmm….well it’s worked ever since the repair, so if I did, ahh well.
My Hyundai Getz l change my back beam and my front brakes are very hot what is the problem
what size compressor did you use to push the piston out?
Compressor size doesn’t matter. It’s an 8 gallon compression.
@@FastFixRUclips thanks ~ so I can buy a small 6 psi compressor with a 110 psi , hopefully that works.
What happen if the seal has tear?
Hello. Dirt and road grime will work its way into the cylinder and eventually cause a failure. Or at minimum cause your breaks to make a lot of noise and not function as well. Thanks for the question.
The job is a bit more tricky than 1.5 rating. Anyone trying this need to know you may damge other components trying to fix this. I would rate this 2.5 out of 5. 😊
Hello. Yes, that’s fair. It’s much easier to just buy a remanufactured caliper, but the cost savings from doing a rebuild is a valid point. 👍
My technique when installing the piston and boot is to place a towel on my lap, place the caliper with the opening facing out ,then use both hands to guide the piston in. Your tummy acts like a back brace.
Another great tip! Yes, do what works for you and that sounds like a good idea for all 👍👍👍
How do you put that seal ring back in?
Not exactly sure where to put that metal ring at.
Hello. The metal ring holds the rubber dust shield in place. It will be the last thing you install. It fits in the groove machined near the lip of the cylinder. I know that didn’t get shown in the video. Sorry about that.
Thank you.
should have show us how you put back the metal ring the right way
Hello. Yes, that piece of footage was regrettably left out. However, it is the last thing to install simply slip it over the boot into the groove. You can’t miss it. I hope everything works out! Thanks for commenting and have a great day.
I have the same car, with the same brake problem!
Honda sold a lot of civics! Best of luck man 👍
Wish I would've seen this video before buying a new rear caliper.
Next time!
Gonna try to rebuild mine from a 80 lotus esprit, Hope it works.
Best of luck!