DRAGON maybe the most expensive headache i had ,either than paying 800 dollars or close to it did not worked with perfection more than 6 monthes, when the summar arrived i stoped it with C90 tdk cassettes ,the SA or chromesuperII from basf it started to make a vibration but if the C60 all was ok so i stoped it and bought a real good deck ,the TEAC Z-7000
and i never used dolby and no hiss, if hiss demagnatise it and it´s solved, those tdk in the shape of a cassette, very handy PIIIIIIIIIIIIIIIII....PIPIPIPI, it´s done (i´m laughing with the piiipipipi)is how it sounds
I know those belts, they sell by the 100 pack, very useful to tidy up power cables of the units in storage... but the last bundle is sealed with ziptie and wrapped in LD-PE soft sheet, so the back of the units will not be scratched.
Hey there thanks as always for yet another brilliant video - we are lucky to see with our eyes the kind of work that goes into restoring these decks. My question is how was the W&F result? Did you manage to return to factory spec? Are you using PRB for the ZX-9s or are you having better luck with the Chinese made belts? Many thanks 🙏🏻
@@hifirulezzz Nice thanks for the info. You are right I did not watch until the very end! I stopped at 57:36ish mark when you said thanks and bye bye 😂 The readings I get with PRB and webspareparts are pretty poor - especially in the classic mechanisms. Depending on the deck I get a stable reading somewhere between 0.065 - 0.105 %. Often where possible I would rejuvenate the original belt and reinstall it, then getting better results on or closer to 0.045%. This is the case for many of my decks, 680/ZX-7/682ZX/LX-5/RX-505/BX-300 and others. Luckily my CR-7 sits at around 0.026% (original belt) which makes it my principle deck for recording. How easily sourced are the belts that you buy? Can they be purchased in small enough quantities, or just in bulk? Many thanks again. ✌🏻
It is a direct drive. What do you mean??? Direct drive mean the motor drives capstan directly. Second capstan always driven with belt with exception of Revox and Nakamichi Dragon. Dragon need it to be capable to do a reverse. Revox did it for fun.
So satisfactory to watch how much dedication you put on these machines, lucky whoever are using these decks gone through your magical hands, honoured just to watch your videos
Always liked the Zx-9
Great job. 🎉
Wonderful repair
this is my favorite model that belonged to my father and i had a 700ZXL wich was incredible good
DRAGON maybe the most expensive headache i had ,either than paying 800 dollars or close to it did not worked with perfection more than 6 monthes, when the summar arrived i stoped it with C90 tdk cassettes ,the SA or chromesuperII from basf it started to make a vibration but if the C60 all was ok so i stoped it and bought a real good deck ,the TEAC Z-7000
and i never used dolby and no hiss, if hiss demagnatise it and it´s solved, those tdk in the shape of a cassette, very handy PIIIIIIIIIIIIIIIII....PIPIPIPI, it´s done (i´m laughing with the piiipipipi)is how it sounds
I know those belts, they sell by the 100 pack, very useful to tidy up power cables of the units in storage... but the last bundle is sealed with ziptie and wrapped in LD-PE soft sheet, so the back of the units will not be scratched.
Hey there thanks as always for yet another brilliant video - we are lucky to see with our eyes the kind of work that goes into restoring these decks.
My question is how was the W&F result? Did you manage to return to factory spec? Are you using PRB for the ZX-9s or are you having better luck with the Chinese made belts?
Many thanks 🙏🏻
I installed a Chinese belt in this deck. W&F is in the video. You did not watch it in full and asking :)
@@hifirulezzz
Nice thanks for the info. You are right I did not watch until the very end! I stopped at 57:36ish mark when you said thanks and bye bye 😂
The readings I get with PRB and webspareparts are pretty poor - especially in the classic mechanisms. Depending on the deck I get a stable reading somewhere between 0.065 - 0.105 %. Often where possible I would rejuvenate the original belt and reinstall it, then getting better results on or closer to 0.045%. This is the case for many of my decks, 680/ZX-7/682ZX/LX-5/RX-505/BX-300 and others. Luckily my CR-7 sits at around 0.026% (original belt) which makes it my principle deck for recording.
How easily sourced are the belts that you buy? Can they be purchased in small enough quantities, or just in bulk?
Many thanks again. ✌🏻
Surprised such an acclaimed deck is not direct drive. Capstan spd relies on a $10 belt LoL
It is a direct drive. What do you mean??? Direct drive mean the motor drives capstan directly. Second capstan always driven with belt with exception of Revox and Nakamichi Dragon. Dragon need it to be capable to do a reverse. Revox did it for fun.
So satisfactory to watch how much dedication you put on these machines, lucky whoever are using these decks gone through your magical hands, honoured just to watch your videos
@@ajayb100 Thank you. Appreciate your feedback.