@@EVCustoms I am currently trying to upgrade my Ebike. I bought a new controller with a paired LCD. For the life of me I can't get the throttle or the PAS to pick up at all
@@EVCustoms I want your help , I have an electric scooter and its controller was burnt and I searched a lot and could not find the same so I bought another one but I did not know how to connect it, can you help me with that please?
Hello despite your very very clear videos because I have seen several I have not been able to bring life to my thumb lcd display which I think is called S2_Y1_c3 with controller XM-K3-C-V1note that the connectors from thumb lcd consist of 6 wires White, bleu, yellow, red, green, black while from control only 5 wires bleu, yellow, red, black, green wondering if you can please explain how to connect them Knowing that this Thumb LCD can be Supplyed with 12.24V and 36V according to the manufacturer which I think is called Lenzod for both parts
Very good work.i was searching for the exact video for a long time, and then finally I found this...perfect... Just have one little issue that the speed o meter is not shwoing working just shwoing 0 ..pls, any advice
It won't work because there is no RX and TX that analyze speed. So the speed remains zero but the wheel will spin. After a couple of minute it will stop because of LCD time out when no signal from rx tx receive.
Thnx! This is useful and answers the question i had. Is the single wire from controller named: controller signal (think it sends pulsing rpm signal) usable in this configuration?? Thanks again!!
Hello, i really love your channel. It would be even better if you talked a bit on the videos. I have a question, why some speed controllers have a switch to select different top speeds?
The only instructions on programming this LCD that I've found is completely incorrect. Normally it's posted in the item details, saying "P00: Light Brightness, Level 1 is the darkest, level 3 is the brightest; P01: Mileage Unit, 0: KM; 1: MILE; P02: Voltage Level.......blah blah blah". But it's completely wrong. However after a few minutes of what looked like a toddler in an elevator for the first time. I pressed all three buttons in every order possible and have come to this conclusion.... PRESS AND HOLD ⬆️and⬇️ for a few seconds to open/close the SET menu. Press the center 🔵 button to flip through each option. Press ⬆️or⬇️ to change to the preferred amount (I'm still no exactly sure what every Set is for, but feel free to add anything I miss) P0: Voltage 12.0-42.5 P1: No Clue 01.0-24.5 P2: Nope 0-106+ P3: Pass 0-1 P4: 0(kmh)-1(mph) P5: "can I phone a friend?" 0-1 P6: No Idea 0-1 P7: Next 0-1 P8: Still nothing 0-100
I have the same lcd and the only setting I could change is the brightness and miles/km option on speedometer. My electric bike went from 25km/h max speed on 3rd gear peddal assist to 21km/h and I think that could be a fault with controler/lcd display
Hi, can you please be kind enough to send me the tutorial with the connection diagram of all the wires, can this LCD Display work with any brushes controller because I have practically the same one that I've never used finally I think it's the same. Sorry for my English, I'm French, thank you in advance. Best regards Gabriel
Can I know if I can just do a on off switch to the signal for pulse pas? Or push button ? So I just use the yellow cable for it ? No need to give power to the on off switch ?
Buddy these items are not worth to spend when you have a Chinese controller. Simply use pedal assist these kits are actually not designed for fully automated type of use.
i have this exact display. It is working like in your video but i would like to have communication rx and tx working. Do you know why it is not working ? is the protocol UART? do you have any idea how to get it to work. I have seen this disay selling on aliexpress on different controllers, maybe the display needs another firmware?
Hello Place tell me can I do this on me e-bike Ariv Meld my motor in good but the battery is broken and I didn't found to buy one. The General Motors stop production part's. Battery reference 43v 6 Ah Motor 250w-635W max the power Wh 259 Thx good video!!!!!
The colore code of all display wire is the same? I mean +, -, switch on, tx and Rx... Connecting this wires correctly any display will work to any controller?
Tell me how to train the controller 48V, 21A, JX-100-ABS-Electron, YKGT06FOC01-A, with a hall sensor, the new one was simply turned off for sealing and everything does not turn, the rest is all on, the speeds switch, the display works? There is no white wire or XX. (The wheel did not spin right away; it needs to be turned a little. Some scooters have this function.)
I have an old lcd display s810 (4 pin) by lcd s866 5 pin, in the electric bike control box it has 4 pin, no possibility to connect a 5 pin to 4 pin connector via adapter.
I think it would make the controller suffer because the pas is not giving a constant signal, like pushing the throttle to max and then back to zero. That goes on and on as you push the pedal
Hey buddy cool videos. I'm going to buy a kunray controller to run my high rpm bldc but is it technically possible to wire a cycle analyst connector into it? Thanks.
I need help, I seem to have a controller with a display port and a throttle port but the current throttle I have in a 5 wire on the display port, I got a new three wire throttle and a new S866 and I'm sure I can plug the display in where the current throttle is and the throttle to the throttle but now there's no PAS port :(
Hello, I have a pedelec with 3 levels and a pass sensor. I would like to add a throttle. But my controller only has the PAS connection and the connection for the 3 speed levels. Is there still a way to retrofit it? THANKS!!
Checked all pins inside my controller from Aliexpress,shorted to ground all with 5V {350W 36V} and there is no CRUISE control,is it possible,what to looking for ?.Only found EBS brake on A3 pin.😃
best regards friend, I need your help, I have a skateboard that uses the same screen, but the screen is cracked and the skateboard was working fine but it stopped working in high speed and only goes in slow speed, so I just want to ask you this: apparently the screen connection cables are in the same order but in mine between the black cable and the red cable there is a blue cable and not orange like in yours and I suppose it is the same one from the ignition so that it turns on and I suppose that if I join the red cable with that blue cable, which in his case is orange, I should turn on the skateboard without the need for said screen, but I measure that blue cable with the tester and it gives me the same 28v that it gives between the black and the red, that is, it behaves as if it were another negative and I am afraid to do the test lest a short circuit occur and end up burning the controller... please help me, if joining that blue cable with the red one should turn on the skateboard without the pa ntalla because we have to assume that it is the same order of the cables because the screen and its connector are identical to the one in your video.... thank you very much God bless you and I already subscribe to your channel
Hey thanks for the video. Could you please tell me, after you have installed the hand throttle, will the PAS still function as normal when the pedals are turned, or does this modification bypass the PAS system completely?
Точно такой же дисплей (я думаю, контроллер и мотор тоже) установленны на ebike Axon rides pro max в Великобритании. Он читается очень качественным и стоит более 2000 фунтов, но мягко говоря, если этот дисплей выглидит как на 200 рублей, так и сам елекробаик качества "рога и капыта"
Hello,I want to make one question,I have one TTX 60v and I have problem with the speed meter, suddenly stopped showing the kilometers and speeds. Thank you very much and I hope to you are all well.
Mein Abo hast bekommen ,ich glaube ich brauche bald deine Hilfe wegen LCD Umbau, ich habe mir einem gebrauchten gekauft aber der Stecker ist anders und wegen Drähte hab ich angst das ich nicht Kurzschluss passiert 😢😢
Hello Mister. I have an ebike controller with S5 / 250W lcd display. Everything was working fine and yesterday the lcd display shows empty battery, the empty battery symbol and it flashes. the battery is however well charged what would be the origin of the problem and how to deal with it
The only instructions on programming this LCD that I've found is completely incorrect. Normally it's posted in the item details, saying "P00: Light Brightness, Level 1 is the darkest, level 3 is the brightest; P01: Mileage Unit, 0: KM; 1: MILE; P02: Voltage Level.......blah blah blah". But it's completely wrong. However after a few minutes of what looked like a toddler in an elevator for the first time. I pressed all three buttons in every order possible and have come to this conclusion.... PRESS AND HOLD ⬆️and⬇️ for a few seconds to open/close the SET menu. Press the center 🔵 button to flip through each option. Press ⬆️or⬇️ to change to the preferred amount (I'm still no exactly sure what every Set is for, but feel free to add anything I miss) P0: Voltage 12.0-42.5 P1: No Clue 01.0-24.5 P2: Nope 0-106+ P3: Pass 0-1 P4: 0(kmh)-1(mph) P5: "can I phone a friend?" 0-1 P6: No Idea 0-1 P7: Next 0-1 P8: Still nothing 0-100
I have wired up my screen and nothing is happening, I have a full battery and the screen comes on, but my motor won't activate, iv put the wires in the color order but its dead, can you help me im bloody up the wall
Hi guys, I found that this thumb model use with S6-65 controller But it's digital! uart pack monitor by logic analyzer. BR 1200. it show out UWuu WUUu in bus line. So I can't find what cable it give analog mode. Anyone face same issue let meknow.
have a problem with this display when I turn on this screen appears with 4 0000 and I cannot make it work because I do not know the code can you help me please?
Is there any lcd display supports up to 60V? Can someone give me leads for the link to buy? Tried to search on Aliexpress but I only saw all are up to 48V. Thank you
Hi friend, do you know how the PAS sensor works and how can we do it to start instantly instead of starting with delay? it would be very interesting if the PAS sensor worked like an accelerator, how can that be done?
Ild be curious if you see the PAS sensor PCB offered anywhere. Ive searched for biggest part of a year. All I find are simple hall sensors and magnets nothing at all abouit the little PCB to add or replace in a controller.. It doesnt seem that such a simple gizmo would be proprietary or special codes.
Hello i don’t know so much about e bike someone build me an Ebike everything works good accept for the display it don’t have the display can u please help me
Salve io vorrei sapere se si può fare il contrario cioè una centralina del monopattino farla andare con un accelleratore a dipley de la bicicletta grazzie
Help: I got a new controller and it only got one pin that says (lcd display) and one pin that says (instruments). I have never seen this before 🫠 I now got a 5 pin and don’t know how to connect them to start 🤓🤓 hope you can help🫨
hi.i have a smart bms. blutooth.i have connected and can see cells on my android phone.my battery is 13s5p.app says one battery 3.6v an rest nearly 4v.im trying to balance on the app.. when compare bms voltage with battery voltage 51,7v at battery but when measure bms black discharge leads to positive its only 16volts.is that right?it does show 51.7v on the app from my battery
EV - Customs yes just done that now voltage from bms - load to battery +was only 16v before now after I made battery 14s it’s full voltage 55v at bms output 😀
you owe me 13 minutes of life. Why on earth won't you say from the begining the display is worthless. You could have as well just taken the thumb accelerator to the controller and toss the screen away -_-
![Lil Uzi Vert - Chill Bae [Official Music Video]](http://i.ytimg.com/vi/D7F42F_JM3U/mqdefault.jpg)
I've learned so much from you in the last couple days. Sadly it hasn't helped in my situation yet but I'm not giving up just yet. Thank you sir 💪🏼
Thanks mate.. Tell me your problem.... maybe i can help you..
@@EVCustoms I am currently trying to upgrade my Ebike. I bought a new controller with a paired LCD. For the life of me I can't get the throttle or the PAS to pick up at all
@@EVCustoms I want your help , I have an electric scooter and its controller was burnt and I searched a lot and could not find the same so I bought another one but I did not know how to connect it, can you help me with that please?
yes... send me photos of your wiring to my email.
@@EVCustoms I have sent them to you via email now😊
Hello despite your very very clear videos because I have seen several I have not been able to bring life to my thumb lcd display which I think is called S2_Y1_c3 with controller XM-K3-C-V1note that the connectors from thumb lcd consist of 6 wires White, bleu, yellow, red, green, black while from control only 5 wires bleu, yellow, red, black, green wondering if you can please explain how to connect them
Knowing that this Thumb LCD can be Supplyed with 12.24V and 36V
according to the manufacturer which I think is called Lenzod for both parts
Very good work.i was searching for the exact video for a long time, and then finally I found this...perfect...
Just have one little issue that the speed o meter is not shwoing working just shwoing 0 ..pls, any advice
It won't work because there is no RX and TX that analyze speed. So the speed remains zero but the wheel will spin. After a couple of minute it will stop because of LCD time out when no signal from rx tx receive.
Good job. Did you manage to connect the speed sensor?
God bless you for this video, it really helped 👍🏽
Thnx! This is useful and answers the question i had.
Is the single wire from controller named: controller signal (think it sends pulsing rpm signal) usable in this configuration??
Thanks again!!
Exactly this is pulse signal from Controller to your display... (speed output)
@@EVCustoms so how to connect it that way? I don't have ignition on of wires (orange and red from controller)
Great video. I bought lcd display, it has five wire. B but my bike have 7 wires.
Если от дисплея 5 проводов, то обмен с контроллером идёт по цифровой шине RX TX. Такая связка работает лишь с совместимыми контроллерами и дисплеями.
Bonjour, ta vidéo est vraiment super
Hello, i really love your channel. It would be even better if you talked a bit on the videos. I have a question, why some speed controllers have a switch to select different top speeds?
The only instructions on programming this LCD that I've found is completely incorrect.
Normally it's posted in the item details, saying "P00: Light Brightness, Level 1 is the darkest, level 3 is the brightest;
P01: Mileage Unit, 0: KM; 1: MILE;
P02: Voltage Level.......blah blah blah". But it's completely wrong.
However after a few minutes of what looked like a toddler in an elevator for the first time. I pressed all three buttons in every order possible and have come to this conclusion....
PRESS AND HOLD ⬆️and⬇️ for a few seconds to open/close the SET menu.
Press the center 🔵 button to flip through each option.
Press ⬆️or⬇️ to change to the preferred amount
(I'm still no exactly sure what every Set is for, but feel free to add anything I miss)
P0: Voltage
12.0-42.5
P1: No Clue
01.0-24.5
P2: Nope
0-106+
P3: Pass
0-1
P4: 0(kmh)-1(mph)
P5: "can I phone a friend?"
0-1
P6: No Idea
0-1
P7: Next
0-1
P8: Still nothing
0-100
I have the same lcd and the only setting I could change is the brightness and miles/km option on speedometer. My electric bike went from 25km/h max speed on 3rd gear peddal assist to 21km/h and I think that could be a fault with controler/lcd display
I don't have the orange wire. Can you help?
This guy is great love this video explains it that needs to be explained makes it look easy keep up the good work
how does it explain.? he is silent
Hi, can you please be kind enough to send me the tutorial with the connection diagram of all the wires, can this LCD Display work with any brushes controller because I have practically the same one that I've never used finally I think it's the same.
Sorry for my English, I'm French, thank you in advance. Best regards Gabriel
Can I know if I can just do a on off switch to the signal for pulse pas? Or push button ? So I just use the yellow cable for it ? No need to give power to the on off switch ?
I mean on the controller green cable . So I just put a push button to the green cable will it works?
Hi! want to know why need to run a long red wire to batttery ? is the red wire from the controller no power?
May as well buy a esc that comes with the screen for around £40 but nice to see how this way is done 👌
Buddy these items are not worth to spend when you have a Chinese controller. Simply use pedal assist these kits are actually not designed for fully automated type of use.
Great video very insightful and helpful however the music on the video made my ears start to bleed...no!
P l
Turn the volume down…….
Thanks sir .. clear .. thanks
Silly question, but are you able to use the LCD throttle on a "brushed" motor? Please do a video!
i have this exact display. It is working like in your video but i would like to have communication rx and tx working. Do you know why it is not working ? is the protocol UART? do you have any idea how to get it to work. I have seen this disay selling on aliexpress on different controllers, maybe the display needs another firmware?
Hello Place tell me can I do this on me e-bike Ariv Meld my motor in good but the battery is broken and I didn't found to buy one. The General Motors stop production part's. Battery reference 43v 6 Ah Motor 250w-635W max the power Wh 259
Thx good video!!!!!
The colore code of all display wire is the same? I mean +, -, switch on, tx and Rx... Connecting this wires correctly any display will work to any controller?
off course not
Tell me how to train the controller 48V, 21A, JX-100-ABS-Electron, YKGT06FOC01-A, with a hall sensor, the new one was simply turned off for sealing and everything does not turn, the rest is all on, the speeds switch, the display works? There is no white wire or XX. (The wheel did not spin right away; it needs to be turned a little. Some scooters have this function.)
Hello ,y need your help,i have changed a screen identical to this one but the scooter does not work,it only uses 5 cables of 6
I have an old lcd display s810 (4 pin) by lcd s866 5 pin, in the electric bike control box it has 4 pin, no possibility to connect a 5 pin to 4 pin connector via adapter.
My motor controller do not provide PAS terminal, can i install PAS parallel to the throttle line of motor controller?
I think it would make the controller suffer because the pas is not giving a constant signal, like pushing the throttle to max and then back to zero. That goes on and on as you push the pedal
I bought a brainpower 36v 1000w and i have the eye throttle with display but theres no display wiring.can i hook it up another way
You are the biggest !!!
TK very much!!!
Hi, Do you have any idea. How to connect PAS Sensor if BLDC Controller not support (No PAS cables)
Can you tell me how to connect the remote control to the motor drive
Hey buddy cool videos. I'm going to buy a kunray controller to run my high rpm bldc but is it technically possible to wire a cycle analyst connector into it? Thanks.
How do I find out if my controller is compatible with a digital display?
I have a 36v sidofo. It has thumb on right and LCD thumb on left. Why does only the right thumb work but not LCD thumb?
If you have 2 conttrolers you need to connect the display just to one or both or what?
Very nice video. Can the hub motor work without the PAS sensor.
Hello friend. Yes of course...
Can Ü bypass the display screen all together and just have a twist throttle only ? No PAS
I broke the handle throttle can I bypass that
@@EVCustoms i broke the throttle can u bypass that and just run it on high
@@javierbautista9661 you can bypass it with variable resistor or push button..
I have a chinese controller and i bought a QS-S4 controller but when i connect it it says E-10 should i change the wirings?
I need help, I seem to have a controller with a display port and a throttle port but the current throttle I have in a 5 wire on the display port, I got a new three wire throttle and a new S866 and I'm sure I can plug the display in where the current throttle is and the throttle to the throttle but now there's no PAS port :(
Hi friend,, PAS port must be wire straight from the controller..
Hello,
I have a pedelec with 3 levels and a pass sensor. I would like to add a throttle.
But my controller only has the PAS connection and the connection for the 3 speed levels.
Is there still a way to retrofit it?
THANKS!!
Checked all pins inside my controller from Aliexpress,shorted to ground all with 5V {350W 36V} and
there is no CRUISE control,is it possible,what to looking for ?.Only found EBS brake on A3 pin.😃
For reverse mode the motor must be completely stopped.. try it again..
best regards friend, I need your help, I have a skateboard that uses the same screen, but the screen is cracked and the skateboard was working fine but it stopped working in high speed and only goes in slow speed, so I just want to ask you this: apparently the screen connection cables are in the same order but in mine between the black cable and the red cable there is a blue cable and not orange like in yours and I suppose it is the same one from the ignition so that it turns on and I suppose that if I join the red cable with that blue cable, which in his case is orange, I should turn on the skateboard without the need for said screen, but I measure that blue cable with the tester and it gives me the same 28v that it gives between the black and the red, that is, it behaves as if it were another negative and I am afraid to do the test lest a short circuit occur and end up burning the controller... please help me, if joining that blue cable with the red one should turn on the skateboard without the pa
ntalla because we have to assume that it is the same order of the cables because the screen and its connector are identical to the one in your video.... thank you very much God bless you and I already subscribe to your channel
i would watch this video if u turned the music off and just talked us thru it.
I think in this case it makes more sense to buy just throttle with power switch and multimeter on it... Just my. 01
With you my friend.. but many Subs ask me how to connect controller with out display wires to display,,
Hey thanks for the video. Could you please tell me, after you have installed the hand throttle, will the PAS still function as normal when the pedals are turned, or does this modification bypass the PAS system completely?
@@DaymeEdna no PAS function on it. You need rx TX lines to be connected.
Hi... PAS will work properly, but not from display 1-2-3 modes...
;) it will work straight from controller with only one mode... He will not be able to change pedal assistant modes...
Legend.
Точно такой же дисплей (я думаю, контроллер и мотор тоже) установленны на ebike Axon rides pro max в Великобритании. Он читается очень качественным и стоит более 2000 фунтов, но мягко говоря, если этот дисплей выглидит как на 200 рублей, так и сам елекробаик качества "рога и капыта"
IT works on my 36 brushless controller but I can't change Speed, do You Have a solution for that ?
Hello,I want to make one question,I have one TTX 60v and I have problem with the speed meter, suddenly stopped showing the kilometers and speeds.
Thank you very much and I hope to you are all well.
same problem did you find a solution buddy?
would this work on a ac induction controller?
Mein Abo hast bekommen ,ich glaube ich brauche bald deine Hilfe wegen LCD Umbau, ich habe mir einem gebrauchten gekauft aber der Stecker ist anders und wegen Drähte hab ich angst das ich nicht Kurzschluss passiert 😢😢
Hello Mister.
I have an ebike controller with S5 / 250W lcd display.
Everything was working fine and yesterday the lcd display shows empty battery, the empty battery symbol and it flashes.
the battery is however well charged
what would be the origin of the problem and how to deal with it
would you happen to have the manual for the display in the video?
The only instructions on programming this LCD that I've found is completely incorrect.
Normally it's posted in the item details, saying "P00: Light Brightness, Level 1 is the darkest, level 3 is the brightest;
P01: Mileage Unit, 0: KM; 1: MILE;
P02: Voltage Level.......blah blah blah". But it's completely wrong.
However after a few minutes of what looked like a toddler in an elevator for the first time. I pressed all three buttons in every order possible and have come to this conclusion....
PRESS AND HOLD ⬆️and⬇️ for a few seconds to open/close the SET menu.
Press the center 🔵 button to flip through each option.
Press ⬆️or⬇️ to change to the preferred amount
(I'm still no exactly sure what every Set is for, but feel free to add anything I miss)
P0: Voltage
12.0-42.5
P1: No Clue
01.0-24.5
P2: Nope
0-106+
P3: Pass
0-1
P4: 0(kmh)-1(mph)
P5: "can I phone a friend?"
0-1
P6: No Idea
0-1
P7: Next
0-1
P8: Still nothing
0-100
Hi could you help me hook up my display to a controller that has 2 instrumental lines? I would greatly appreciate it.
Thank you very much!
Bonjour j ai le même digital il fonctionnait j ai voulu faire des réglages il ne fonctionne plus comment le remettre à 0 merci
Do all controllers have an RX And TX?
do you know to adapt throttle to brushed controllers?
Brother can u help me please, my display got jam so i try to fix but it nw not working properly
I have wired up my screen and nothing is happening, I have a full battery and the screen comes on, but my motor won't activate, iv put the wires in the color order but its dead, can you help me im bloody up the wall
What type of controller and which screen are you using? Did you connect the alarm and deactivate it?
Hola, amigo necesito los parámetros de ese pantalla LCD mi scooter está des configurada
Good content but turn the freaking volume down on all the obnoxious banging.
Van waar hebt u de controller gekocht ?
Do you know if DGW07 brushless motor having 41F hall sensors can work with any brushless motor controllers?
How do we make a control bike with a display to a normal throttle lever?
Hi, how to take power from controller for gps tracker black and red wires for power ?
Hi guys, I found that this thumb model use with S6-65 controller But it's digital! uart pack monitor by logic analyzer. BR 1200.
it show out UWuu WUUu in bus line. So I can't find what cable it give analog mode.
Anyone face same issue let meknow.
I need one of these display where I can get one
Первый раз вижу, чтоб так паяльник держали.
Как?
@@EVCustoms угловым изгибом обычно сверху паяют, а жало обычно смотрит вниз
@@Rcomp100 😆
How to make battery
Input:100V-240V~ , 50/60Hz, 2.5A (Max)
output:42v 2A
Battery:36V/4Ah
Power consumption:
have a problem with this display when I turn on this screen appears with 4 0000 and I cannot make it work because I do not know the code can you help me please?
I'm having a problem with my throttle due to weather corrosion
What if i have 72 volt battery?
Is there any lcd display supports up to 60V? Can someone give me leads for the link to buy? Tried to search on Aliexpress but I only saw all are up to 48V. Thank you
It should take 60V even 72+V. It will recognize the voltage and run accordingly.
You did not link/weld the blue wire.. which is data ?!!!!
Good video,,, BUT !!! That damn soldering pencils bent tip annoys the hell out of me! AND I DON'T KNOW WHY!!
Bonjour comment faire 5 bouche vitesse contrôleur je ne sais pas c'est même chose vitesse merci
Hi friend, do you know how the PAS sensor works and how can we do it to start instantly instead of starting with delay?
it would be very interesting if the PAS sensor worked like an accelerator, how can that be done?
I will search that friend....
@@EVCustoms ok thank you friend
Ild be curious if you see the PAS sensor PCB offered anywhere. Ive searched for biggest part of a year. All I find are simple hall sensors and magnets nothing at all abouit the little PCB to add or replace in a controller.. It doesnt seem that such a simple gizmo would be proprietary or special codes.
Hello i don’t know so much about e bike someone build me an Ebike everything works good accept for the display it don’t have the display can u please help me
Salve io vorrei sapere se si può fare il contrario cioè una centralina del monopattino farla andare con un accelleratore a dipley de la bicicletta grazzie
Thanks!
هذا فقط يسمى تمرير التيار الى الشاشة ولو مررته الى شاشة هاتف لاشتغلت فقط مرر الجهد المطلوب
nice 👍 good
Hello dear friends throttle wire don't 😊
Please help, the cables of the same display were unsoldered, I have red, black, yellow, blue and green colors and in the pcb gnd, tx, rx, key and 5v
What is the orange and red wire
Nevermind
Help: I got a new controller and it only got one pin that says (lcd display) and one pin that says (instruments). I have never seen this before 🫠 I now got a 5 pin and don’t know how to connect them to start 🤓🤓 hope you can help🫨
Hi , my Friend, can you help with my controller and its screen?
Great video!!...better music!!
La velocità ? Non la rileva?
Than you alternativ i fix mine
Price
Do you have the part number for this controller that includes the thumb throttle?
Thank Thee :-)
S2-Y1-C3
Where can I get a fat tire hub motor kit mxus
BIC 💙
hi.i have a smart bms. blutooth.i have connected and can see cells on my android phone.my battery is 13s5p.app says one battery 3.6v an rest nearly 4v.im trying to balance on the app.. when compare bms voltage with battery voltage 51,7v at battery but when measure bms black discharge leads to positive its only 16volts.is that right?it does show 51.7v on the app from my battery
Set it on static balance mode... An live it 2-3 days
Ok thanks
Just added extra row it’s 14s now an all cells with .1v .on smart bms do I take load to bike from bms or battery ?
@@stevemcgowan3017 If you need low voltage-hi voltage and current protection, you must take power output from BMS...
EV - Customs yes just done that now voltage from bms - load to battery +was only 16v before now after I made battery 14s it’s full voltage 55v at bms output 😀
Wuao!!!👏🏻👏🏻👏🏻👏🏻
my controller is these connecting rings on them
Sir what means data RX and data TX.
Hi... RX and TX is communication of controller with screen
"R"ecieving Data. And "T"ransmeting Data I thought .
Or not???!!!
you owe me 13 minutes of life. Why on earth won't you say from the begining the display is worthless. You could have as well just taken the thumb accelerator to the controller and toss the screen away -_-
Así no me entero de nada tendría que ser explicado 😑
Ne se polucava kakto e na klipa nesgto
👍
Hi, what if my motor only have 5 hall sensor wire?
???? What you mean?