that “stay within the bevel” comment is golden wey, idk how many times i planned to do a 3 bead cap and end up doin 4 because i blew my bevel out onna fill for movin too wide.
It happens to all of us brother. Trying to keep the welds clean you over think. When in reality is as simply as staying within. Thanks for watching bro. This shit has happened to all of the welders I guarantee.
Land always uniform and same thickness both sides. Then you only have to look at the top of the land to know exactly what is inside . When doing Tie ins it makes life easy and your heat sink is uniform too
This is an awesome video as well as awesome looking beads. I'm new to welding & have been out in my shop practicing & running beads & joining pieces together. I've been learning the basics from my brother, who has been welding for 30 yrs. I do have a couple questions for ya & I apologize for asking. . . . . .1.) "What is the reason for leaving the small gap between your 2 pipe pieces before ya begin running your joining root pass? 2.) Why not let the 2 pieces touch directly to each other & then start your joining root pass? Thankya for sharing. I hope I can be as good as ya'll😃👍🏼
You don’t have to apologize brother. No question is stupid in this world. But the gap in between the two joints is too adhiere inside penetration. Without a gap it’s possible to get a root in but you will have a harder time.
@@VantageWelding Okie dokie. . . . I really appreciate ya taking the time to text me back to answer my questions.. Thankya sir. I'm trying to learn all i can👨🏭 & get in the much needed practice👨🏭. I've been trying my best with the "uphill", using 1/8 7018, but i suck & i dont like the 7018 rod. I'm running at 115amps. I'm using an ole 50 yr old Lincoln 225amp arc welder that's in great shape. My grandpa bought it in the mid 70s & dad used it thru the yrs until 2016. I'm having alot of fun, needless to say😃👍🏼. Im a new subscriber to your channel, if that's okay with ya👍🏼!
I can give you a tip. When you pull out, pull out by pushing down and away from puddle. That would leave a voided space shaped like a spoon. You go back into that cracker, refill and take off.
Think you can do a 6010 5p all the way out , haven’t seen a video yet of people doing 6010 caps. Been looking around to see what motion guys use to get it nice and stacked.
Same thing bro. No lie. 6010 doesn’t like to stack as good as 7010 or 8010. So for your last fill I’d leave it a bit bumpy so you can just skate a cap on there.
Slick.. if you had the choice. Would you rather cap wit 6010 7010 or 8010. I'm normally a TIG 7018 kind of welder but lately I've been doing a lot of downhill 6010 at work I was wanting to buy some 70 or 80 but not sure what would run better
I don’t really like to use 6010 other than for the roots due to the fact that they won’t carry metal as good as a 8010. 8010s freeze up faster than a 6010. And as far as 7010, you can slick those out too as well, just get ready to get burned the **** up lol. I prefer a hood ol’ 8010 pipeliner over any rod. 8010 downhill over any process. 🦾🦾 thanks for watching
La MB jorjiyo Vasquez
Ese eres tú mi chingon.
More welding tutorial brother you're the best welder I saw here in RUclips so far and also a good teacher
Hey thanks brother. I appreciate the support.
Your a perfect teacher these video's are gold thanks for sharing this.
Thanks buddy.
Yes! A very good teacher.
Very good detailed video, clear and simple instructions 👌
Thank you
Thanks for the knowledge bro, you explain the different procedure real simple , blessed.
Thank you for watching brother.
My boy pulled out the pesos !! 😂🔥
5 peso landing. 😅😅🙌🙌
@cyberisticgal7991 it’s never too late to do it right 🤪
Great channel son,im no pipe welder but learned a lot about stick from your videos
Thanks for watching budd
i've seen a ton of welding videos and this was the best by far. great content and simple to folloow
I appreciate that brother.
@@VantageWelding Now next time do the root uphill and make it look like the one you did it going down, IF YOU CAN. I bet most pipelining nggas can't.
Downhill, uphill, side to side. No gap too small no crack too wide. Can weld anything from the crack of dawn to a broken heart!!
@@VantageWelding lol even parrots can talk.
It’s not that hard. Don’t let it get your blood boiling brother. Welding is not that hard. I appreciate you watching and cumming back here for more. 💦
that “stay within the bevel” comment is golden wey, idk how many times i planned to do a 3 bead cap and end up doin 4 because i blew my bevel out onna fill for movin too wide.
It happens to all of us brother. Trying to keep the welds clean you over think. When in reality is as simply as staying within. Thanks for watching bro. This shit has happened to all of the welders I guarantee.
Hell yeah looking good ! Damn good teaching
Thank you for watching sir
Great video young man and great welding too!
Thank you sir.
Nice brotha! Thanks for sharing 🤙🤙🤙
Thanks for watching budd
You are so skillful .
Thank you brother.
Roll em and slick em out! 👌🏾
🫡
Land always uniform and same thickness both sides. Then you only have to look at the top of the land to know exactly what is inside . When doing Tie ins it makes life easy and your heat sink is uniform too
Yes sir
This is an awesome video as well as awesome looking beads. I'm new to welding & have been out in my shop practicing & running beads & joining pieces together. I've been learning the basics from my brother, who has been welding for 30 yrs. I do have a couple questions for ya & I apologize for asking. . . . . .1.) "What is the reason for leaving the small gap between your 2 pipe pieces before ya begin running your joining root pass? 2.) Why not let the 2 pieces touch directly to each other & then start your joining root pass? Thankya for sharing. I hope I can be as good as ya'll😃👍🏼
You don’t have to apologize brother. No question is stupid in this world. But the gap in between the two joints is too adhiere inside penetration. Without a gap it’s possible to get a root in but you will have a harder time.
@@VantageWelding Okie dokie. . . . I really appreciate ya taking the time to text me back to answer my questions.. Thankya sir. I'm trying to learn all i can👨🏭 & get in the much needed practice👨🏭. I've been trying my best with the "uphill", using 1/8 7018, but i suck & i dont like the 7018 rod. I'm running at 115amps. I'm using an ole 50 yr old Lincoln 225amp arc welder that's in great shape. My grandpa bought it in the mid 70s & dad used it thru the yrs until 2016. I'm having alot of fun, needless to say😃👍🏼. Im a new subscriber to your channel, if that's okay with ya👍🏼!
🔥🔥🔥going back on all the clips anytime i get a chance and reaction is still like MAINE🔥🔥🔥
Thanks brother. I appreciate the love homie.
muy buen video y expicas muy bien el proseso de soldar saludos
Saludos Chalo. Gracias por su apoyo hermano.
I always leave wagon tracks unless I'm using 7018 on the next pass 6010 7010 will dig all trash out
Buen videos, gracias !
wow, great weld
Thank you
Great Advice Brother! 🤘🏽
Gracia carnal.
Thanks for the video. Why do you use a 6010 for the root? Why not 7018 for that as well? or some other rod, like a 6013?
6010 +++ is specified for root passes. 7018 is not a penetrating rod. And 6013 is a cheap farm rod not intended for use in quality welds.
🔥💯
🤝
Wow welding appearance
Can you do a video with tips on how to do restarts on your cap with 8010. ?
I can give you a tip. When you pull out, pull out by pushing down and away from puddle. That would leave a voided space shaped like a spoon. You go back into that cracker, refill and take off.
Wally the weld professor has some awesome content regarding restarts on 8010. One of the slickest welders out there brother.
Think you can do a 6010 5p all the way out , haven’t seen a video yet of people doing 6010 caps. Been looking around to see what motion guys use to get it nice and stacked.
Same thing bro. No lie. 6010 doesn’t like to stack as good as 7010 or 8010. So for your last fill I’d leave it a bit bumpy so you can just skate a cap on there.
Good welder
😂
Quality
🫡
You're a very good teacher. I want to thank you for your video. Also is your pipeliner hood cut down at all?
Thank you. And no brother. It’s still not cut brother.
@@VantageWelding ok thanks man
Slick.. if you had the choice. Would you rather cap wit 6010 7010 or 8010. I'm normally a TIG 7018 kind of welder but lately I've been doing a lot of downhill 6010 at work I was wanting to buy some 70 or 80 but not sure what would run better
I don’t really like to use 6010 other than for the roots due to the fact that they won’t carry metal as good as a 8010. 8010s freeze up faster than a 6010. And as far as 7010, you can slick those out too as well, just get ready to get burned the **** up lol. I prefer a hood ol’ 8010 pipeliner over any rod. 8010 downhill over any process. 🦾🦾 thanks for watching
Down hill I’d run 8010 for fill and cap
💪🏾💪🏾
Can you do a video on how to tie into the tacks, I’m having trouble tieing in on my 6g. Not sure if I’m grinding to much??
It’s at minute 6:46 were I tie in.
If you’re blowing through you either
A. Grinding too much
B. Excess Amperage
Классная работа!!!!
Thank you brother.
@@VantageWelding да хотел бы так научится варить катушку сдавал не прошла увы!!
was that all done with DC? 6010 8010
Yes
Where do you get that T from for the weld gap?
Heavy duty shipping strap brother.
You had a 💩 load of porosity in those weld beads!
Nope. I don’t think so. Good observation though.
No pues q chido rolando la pipa así quien no
Como caiga.
сойдет 🤟👋
I'm tyrophobia 😁
Hi Tyrophobia, I’m Jorge. 😂
@@VantageWelding 😂😂😂
Cap too Convex...!!!
🥺🥺😢😢
Not that Good
😢❤️🩹💔