Hope you can give me some hints about my HUSQ. 326 I put new gaskets in the carb. went to start but no fuel appears in the fuel line of the primary ---bulb --it is new fuel line from the thank to right side of carb ...... on the left side fuel line from the carbu. to primary ( short connection little pipe) then ( from long little pipe connection f.l.) from primary in the tank ....but steel no fuel flow through the fuel line in/out of primary MAY BE THERE IS A BLOKEGE IN THE CARURETTOR IF IT IS SO WHERE SHOULD I HAVE TO LOOK ? Thank you
The carb might need to be cleaned really good. You can use brakleen to do this. You would have to take the whole carb appart clean eevery little spot with brakleen inside and out then re assemble. If there is a speck stuck some where it have the potential to cause a problem. My link for brakleen amzn.to/3KKmYYV
@@KylesChainsawRescue Thank you so much for your time to answer me ...After so many times in removing the carb. I find out that the fuel line from the tank to the carb. ..---.the carburettor where the f.l .connects it was blocked ---... cleaned it and now i try to starts but because something is wrong it does't come alive---starts---I don't know if I can get the brakleen here in Australia I do use the carburettor cleaning .....WOILD YOU be able to give me an idea what to look for to make the chainsaw to start ?
@@tonyd6821 check spark arrestor , spark plug , gas lines , coil and flywheel gap all filters clean , look into exhaust side and carb side ports to make sure no scoring marks
@@KylesChainsawRescue Thank you for your help ...but I just wont to inform that I put new oil seal , new piston and cylinder new fuel line , new carb. air filter It start then stops I tried to play with the H & L screws but no success I gave it to an expert and he reckons it is the (new) carb . But I think it is not then we will see when the carb . arrives ??
Great video, thank you. Have a 235 that I can’t get running well. Tried a new carb, carb adjustment etc and it still sounds like it is dying 🤯🤯
$20 kit can’t beat it
Hope you can give me some hints about my HUSQ. 326 I put new gaskets in the carb. went to start but no fuel
appears in the fuel line of the primary ---bulb --it is new fuel line from the thank to right side of carb ......
on the left side fuel line from the carbu. to primary ( short connection little pipe) then ( from long little pipe connection f.l.)
from primary in the tank ....but steel no fuel flow through the fuel line in/out of primary MAY BE THERE IS A BLOKEGE
IN THE CARURETTOR IF IT IS SO WHERE SHOULD I HAVE TO LOOK ? Thank you
The carb might need to be cleaned really good. You can use brakleen to do this. You would have to take the whole carb appart clean eevery little spot with brakleen inside and out then re assemble. If there is a speck stuck some where it have the potential to cause a problem.
My link for brakleen
amzn.to/3KKmYYV
@@KylesChainsawRescue Thank you so much for your time to answer me ...After so many times in removing the carb.
I find out that the fuel line from the tank to the carb. ..---.the carburettor where the f.l .connects it was blocked ---... cleaned it
and now i try to starts but because something is wrong it does't come alive---starts---I don't know if I can get the
brakleen here in Australia I do use the carburettor cleaning .....WOILD YOU be able to give me an idea what to look for
to make the chainsaw to start ?
@@tonyd6821 check spark arrestor , spark plug , gas lines , coil and flywheel gap all filters clean , look into exhaust side and carb side ports to make sure no scoring marks
@@KylesChainsawRescue Thank you for your help ...but I just wont to inform that I put new oil seal , new piston and cylinder
new fuel line , new carb. air filter It start then stops I tried to play with the H & L screws but no success I gave it to an
expert and he reckons it is the (new) carb . But I think it is not then we will see when the carb . arrives ??