FlySky Two Servo Aileron Setup

How to setup dual servos for planes that require a seperate servo on either wing. This can be done by either buying a Y connector cable in which nothing will need to be setup other than possibly reversing servos or horns. This video will show you how to mix servos. You still may need extensions to reach your receiver in most cases.

[@ekeomaeke3670]

This helped me a lot. Cause I'm currently building my first rc plane and I'm thinking of a way to control two aileron servos with only one channel. Thanks.😃

[@lalitg.shelare6134]

Thanks it was a great help for beginners

[@theorangebaron1595]

Thank you, you saved me 2 weeks of shipping and 2 bucks.

[@theimpossiblebros8738]

Thank you so much! This is the only place I have found the answer to my question.

[@AndreasBaumgartnerMUC]

Thank you very much mate! Exactly what I was looking for, explanation on point and no "HEEEEEEEYYYYYYY GUUUUUUUUYYYYYYSSSSSS!!!!!!" at the beginning. Sub for sure.

[@ruimessias1302]

Simplicity and awesome mate, you are legend...! Thanks for helping and safe landing as always....

[@carl469]

Thanks... first time it was explained in a way to easily understand!!

[@kaydostandssideways8946]

Yo I thought this vid would have like 25k views more people need to see this

[@egeelcin]

Thanks mate. I connected both servos in a channel first but it didnt work well. This is awesome

[@markhowe5529]

Brilliant !! Just about to jump out the window trying to fathom this out ! Top Man ! Mark UK. PS just subscribed !

[@addisonplummer3531]

thanks dude this was really helpful!!

[@dado1063]

Thanks you helped me a Lot!!!

[@jackjuhasz533]

thanks, great explanation !

[@vincesommer2195]

THANK YOU SO MUCH !

[@lorenzothepasta2820]

Thanks bro!

[@suzxq36]

Thx

[@sadsausage2224]

I did exaclty what u did. But my servo connected to ch6 only turn in 1 direction and pos and neg mix is both 100%, tried ch 5 same problem but ch 4 works. But then my rudder also controls my ailerons

[@MsTobi95]

Had the same issue, now it works well. You have to select on the according aux. channel none.
ruclips.net/video/d02UARXh7LU/видео.htmlsi=yIyZo_zZa8db4Mn_

[@josiahhornbrook1820]

useful :)

[@jamesbloomfield2741]

Too man!! You've just saves me £2.50!!!!

[@peterkennethnuevo8551]

Does the Fsi6X support receivers with gyros?

[@did3d523]

how use Gyro stabilizer A3V2 in this config?

[@jannovak2234]

hi.dear sir, Tell me pleas ,this rádio used timer???

[@arekdamopoulos1916]

It is possible to make this servos with another switch to lock down for flaps?

[@davidjust548]

Absolutely. I like to use the C switch for this since it’s a 3 position switch. You will need to dedicate the switch to an unused channel, then use a secondary mix that assigns your flaperons that you mixed to that channel.

[@arekdamopoulos1916]

@@davidjust548 Okey, thanks, the only problem is 2/3 mix lose

[@mohammadmatindehghani711]

I have a flysky i6x
I want to warn in weak signals(rssi alarm or low signal alarm)
Do I need to update the firmware?
🙏🏻🙏🏻🙏🏻🙏🏻🙏🏻please guide me

[@davidjust548]

My TX will alarm when there is signal loss. Not sure if there is a low signal alarm. I know when I am ridge soaring and land on the back side of the hill it will lose signal leading me to believe the signal is line of sight. Once I begin walking toward my plane, it recovers the signal with a secondary alarm.