Installing DC Converter and Fuse Block to Bintelli Golf Cart
HTML-код
- Опубликовано: 2 июл 2024
- Swapping out the DC converter and fuse block today. I wanted a smaller converter, so it fits better. And, I wanted a safer, all in one, type of fuse block. I’m still going to hang on to the larger converter, for a future project. I’ll mount it up high in the drivers side rear wheel well, opposite of the factory converter.
The new stuff:
HOMELYLIFE 10A 120W Golf CART 48V 36V to 12V Converter Voltage Reducer Step Down Transformer Waterproof
amzn.to/3MVdAmV
6 Way Fuse Block,12V Blade Fuse 6 Circuit ATC/ATO Waterproof Fuse Box Holder with LED Indicator Waterpoof Cover for 12V/24V Automotive Truck Boat Marine RV Van Vehicle
amzn.to/429hTiO
The old stuff:
10L0L Golf Cart Voltage Reducer 36V 48V to 12V 30A 350W, Universal DC Step Down Converter, Regulator, Transformer for EZGO Club Car Yamaha
amzn.to/43sFsEm
Gebildet 6 Way Car Standard Blade Fuse Holder Boxwith 10pcs Blade Fuse (3A/5A/7.5A/10A/15A/20A/25A/30A/35A/40A) and 12pcs Terminals
amzn.to/3WBCN9u 
Авто/Мото
Is your 48v in on a switch of some kind? If not the converter is always drawing off the carts pack, even with no devices turned on. Some converters have a 5th wire that you run to your key switch to turn them on or off. You could also just put in a toggle switch or breaker.
Yep, I forgot to mention that in the video. I put a switch in between the fuse and the converter.
Hi man, good video. Can you tell me what rating fuse you used for this converter, I'm guessing 10 amps because the converter is 12v 10amps, but if it's not, let me know. Or it depends on the device you are connecting.
May not be the most safe thing, the only fuse I had was a 30 amp fuse going to the converter. I would highly suggest a 10 amp fuse though, and I should have probably swapped mine out a long time ago... At the fuse box, I think the biggest one is 10 amps. Most are either three or five amps though for small LED lights, light strips, alarm.
Atleast run a 48 volt relay to the run position of the key to power that converter only when the key is on otherwise that thing is constantly converting 48 volts to 12 volts continuously running your battery down
That is a good idea!
Did you install a relay with this system?
Not for this one. I put it on a switch instead. You can put it on a relay from the ignition switch.
That's not a converter it's a regulator. The problem is you are drawing 4 times the power you need to dumping it as heat. A buck converter would be much better.
A more powerful buck converter is on my wishlist. And it won't drain the battery as much, from what I'm told.
Any suggestions on a buck converter? Something that can power a ton of accessories, lights and a winch too 😁
@@oftenwrongparadigm a winch is going to pull a lot of power. In electric cars the manufacturers have a separate 12v system with it's own battery. That's probably your best bet. lawnmower batteries are cheap. Then charge it with a 500w buck converter.
Goodday .
How do you size the fuses?
For physical size, the fuse holder will tell you what size it uses. For the amps, I would stick close to what the devise manufacturer says, or check it's "max draw" rate and go with that amp rating of a fuse. Going bigger on the amps just makes the fire risk go way up.
@@oftenwrongparadigm thanks for the reply. Great work!