@@АлексейЛебедев-з7впо даташиту, например, ST78M05 входное напряжение до 35В включительно, у всех фирменных стабов этой серии так же, 35В. Так что можно, вопрос в том нужно ли? Если только делать кипятильник для подогрева платы в уличном исполнении.
@user-rf4jl3nc1h 😂😂😂😂 why dont you try that out and check it with an oscilloscope. Obviously, if you are using a linear regulated lab power supply to test the circuit it should already be filtered so thats an unfair test. Use a transformer and rectifier see how that works out.
@@市川麻衣子-t3x It could also do with some protection diodes! But the lower voltage regulators will burn up before then anyway if you need more than milliamps.
Pretty bad design to be honest.. not worth making... Those designs can be improved just by following the datasheet.. it doesn't even take a minute. To check what the recommendation is... The maximum voltage for 7805 is 25volts.. so just by supplying it 30v ,, ahh sketchy stuff.. you are overloading the ic... Lets say you want 500mA current .. well that would be 12.5watts.. that little thing can't withstand it... A regulator always needs a input cap close to input and reverse protection diode.. none of the basic things are even met...🤣🤣 Please don't do it...
Забыл все поставить! 😂 Электролитические конденсаторы на входе и выходе, а так же керамические конденсаторы 0.1-0.3мкФ шунтирующие вход и выход каждого линейного стабилизатора. Теплоотвода нет! Защиты никакой нет! Красиво, но бесполезно! 😊 Проще на одном регулируемом стабилизаторе, собрать схему с регулировкой напряжения от 2.4 до 28 Вольт.
Не всегда это проще например как у бп атх когда надо несколько напряжений разом с небольшим током, а вот то что охлада нет это да, немного не продуманно
Depends if you want any value of voltage in the range or if you just need _standard_ voltages as those provided by the 78xx, 79xx series of regulators. If you are powering logic circuits, you *_don't_* want an adjustable voltage. It means : 1. You risk blowing up the logic circuit, 2. You have the inconvenience of setting the voltage each time and accurately. You then need a multimeter.
@@florinpandele5205 You can have multiple voltages concurrently by having multiple LM317's. The decision to use an LM317 or 78xx or 79xx isn't based on whether you need multiple voltages simultaneously but is based on whether the voltage(s) you need are "standard" fixed voltages that can be provided by the 78xx, 79xx series or whether you want a different and adjustable voltage. Here it is possible for the power supply to provide multiple voltages of fixed voltages concurrently so I do agree that the original poster has missed the point.
اولا هاد تضيع عالي للطاقة ثاني (البور دسبيشن) او التبديد الطاقة عالي على منظم ال5 اكتر شي وبعده ال9 والقانون يقول بانه لا يجب وضع جهد على منظم الجهد اكثر من جهد الخرج بمرتين كحد اقصى يعني مثلا منظم ال9فولت 12فولت تغذية كافية وكتير عليه هنا التبديد 3فولت فقط
Hi👋🤠; The "LMxxxx" series regulators are passive and Do Not shunt excess voltage to ground like a "Zener Diode" so no series dropping resistor is not needed and no extra current is being drawn. I do think though that stableizing capacitors should be used 🤔😉👍👍
Com um auxílio de um dissipador de calor bem robusto vazado com um cooler para fazer a refrigeração do calor. Deve evitar o sobreaquecimento. Já que um dos Ci gera 1A de corrente.
Нужно ставить в последовательную цепочку, 15в стаб питать от 24в, 12в от 15в, 10в от 12 и тд, а то 9, 8, 5 вольтовые при подаче 30 вольт будут чувствовать себя очень плохо.
Крен5 или 7805 от подачи 30 вольт. Просто пыхнет. Это раз. А про остальное сначало нужно посматреть дата шиты на крен, прежде чем их вот так цеплять, А где все теплоотводы?
Not possible without cooling. Especially the 5V regulator. The positive rail is behind the cooling fin. This ist not so clever, because you are risking a short circuit and you are not longer able tu put cooling between the LMs and the PCB. And where are the caps? The regulators will ring like hell. Think first, do once.
Thats a good example how to NOT do it! IN-Output and Filter condenators are missing as fuses as adequate cooling especially with the high input voltage for the low voltage regulators. Half of them are running out of specs and will faster than you think burn out. Correct way would be a transformator with different secundary outputs, each about 3 Volts above the specific regulator. So about 8V for the 5V regulator 12V for the 9V regulator, 15V for the 12V regulator and so on
А тепер згадайте фізику, подивіться даташит, і переробіть цей витвір. По перше розвернути в іншу сторону, від великої напруги і до меншої. По друге всі кренки ставте послідовно, щоб на кожній з них була якомога менша різниця потенціалів. Плюс пару електролітів, одну плівку або кераміку, і як мінімум один діод. Не забуваемо про радіатори, або один, та через діелектричну проставку. Все, тепер цей виріб правильний і надійний.
@@igorzherebiatev5751Всё, я думал он последовально все соединил, от высшего напряжения к нижнему.А он параллельно от общего источника питания.Тогда другая проблема, 5В стабилизатор от 24 вольт будет себя чувствовать очень не хорошо
@@TheSorvig их и надо последовательно, с отбором мощности с какого-то одного. Если их параллельно, то никакого радиатора не хватит для крен5, а 7824 едва работать будет
WOW! It isn't often you get to see so much "WRONG!" in one video. Are you trying to burn down your house? Because that's how you burn down your house, Cheryl...
right out of the gate it's garbage. The thickness of the tracks is not enough for reliable operation. you didn't strengthen them in any way. There are no filter capacitors. therefore, no one needs this simple scheme, because it does not fulfill its functions.
What about input VCC? If you do not adjust it for each regulator you will use, the power output available for the lower voltages will be too low. To much voltage drop across regulators and too much heat dissipation.
Extremely useful!!!… for a rocket/ward head circuit only meant to last a total of/no more than 10 minutes in flight, and even that may be too much 🤣 No capacitors, no diode reverse protections, no heat sinks for dissipation. Im definitely adding this to my saved list of circuits, so I can rebuild it correctly 😂 The most masterful part of this circuit is the self etched board (which I need to analyze on a still frame to make sure is truly correct, given this video) 😂 Cheers boys 🍻
i feel bad boosting this video's engagement but i have to comment that it didnt lie, it is a multi output voltage regulator power supply, it didnt say regulated anywhere in the title so it it isnt a lie
Тем временем здоровые люди берут один 7805, переменный резистор и цифровой индикатор напряжения и собирают на нем регулируемый источник питания от 5 до 22 Вольт. 😂
You must change the circuit by reversing the order of the regulators by connecting them in the waterfall: foods on 7824 with 30 volts, with the exit of the 24 foods on 7818, with the exit of 7818 foods on 7815 and so on. This system will also divide the heat produced evenly.
At least with this design it would be in cascade, so you take advantage of the other job, but the 7805 to reduce from 30v, at minimum I'll recommend this solution.
Зафер, идея занимательная, но имеет ряд недостатков. :) Если нет вольтметра для плавной регулировки выходного напряжения и нужен ряд определённых, фиксированных значений напряжений на выходе, то не проще ли подключать соответствующие стабилитроны к LM317Т ? :)
I would of put a heat sink strip across the top. Also , as the project is good , the Adjustable LM317T would give the voltages outlined here , or even add the LM317T as well.
Идея на 2, плата громоздкая, можно было использовать 1 стабилизатор с возможностью регулировки и резисторы для выбора напряжения, конденсаторов сглаживающих нет, ну и самое главное ужасное КПД, ведь чтобы из 10в получить 5 например нужно половину мощности рассеять, уже давно есть dc-dc преобразователи
Muito bom esse projeto de fonte, várias voltagem em uma fonte só... Só falta fazer uma boa filetagem com uns capacetes de 10.000mf ou mais por 50 ou 63 volts.
Voltagem de entrada destes reguladores,pelo manual dos fabricantes somente o dobro da tensão de saída ( no máximo). Então o 7805 a tensão de entrada é de 10volts. E não 30 volts!
Muy interesante.Pero cuanta mas sea la direncia entre entrada y salida,eso afecta al regulador,esa diferencia se convertira en calor,por decir a asi.(siendo que se alimente a todos con la misma fuente,Xd)✌️
WOULD YOU LIKE TO MAKE ELEVATOR CIRCUIT. i HAVE A CIRCUIT MADE ALREADY BUT NO PARTS. iT REQUIRE A LATCHING RELAY WHICH HOLD THE POWER WITHOUT VOLATGE.. output voltage
1.5A ist just with propper cooling. this design would get nowhere close to that. Remember with the 78XX the excess voltage is converted to heat. So for the 7805 at 30V that would be 25V loss. 25V*1,5A=37,5W in heat losses!
Eficiencia en su maximo explendor, que año estamos? Y ya que estamos, vamos a eliminar la inyeccion electronica, los catalizadores, las fuentes electronicas, las luces led, los correctores de potencia... Porque ir para adelante si podemos hacia atras, montaña abajo
7805 в даташите сказано входное напряжение до 35в но как показывает практика он будет очень сильно нагреватся. Нет конденсаторов на входе и на выходе, а так же диода (анодом на выход, катодом на вход). Ещё радиатора тут очень кстати. А вообще можно убрать все это и на одном lm317 получить напряжение от 1.2в до 37в
Only a thing, the most of 78xx have connectivité between pin base and the disipador part. If yu push on the 78xx you will have a mess because generated a dead Short
30 volt for 7805 is wrong
Everything is wrong here 😂
Way wrong 😢
Всë верно нельзя подавать на 7805 30 вольт
@@АлексейЛебедев-з7впо даташиту, например, ST78M05 входное напряжение до 35В включительно, у всех фирменных стабов этой серии так же, 35В. Так что можно, вопрос в том нужно ли? Если только делать кипятильник для подогрева платы в уличном исполнении.
No actual heatsink either
Why NO Input/output capacitors each regulator?
Plz note the input voltage
@@hinasamal8406 What do you mean?
Three terminal regulator require capacitors
for stopping oscillation.
other persons point out same point.
Линейному стабилизатору не нужны конденсаторы, только радиатор.
@user-rf4jl3nc1h 😂😂😂😂 why dont you try that out and check it with an oscilloscope. Obviously, if you are using a linear regulated lab power supply to test the circuit it should already be filtered so thats an unfair test. Use a transformer and rectifier see how that works out.
@@市川麻衣子-t3x It could also do with some protection diodes! But the lower voltage regulators will burn up before then anyway if you need more than milliamps.
Pretty bad design to be honest.. not worth making...
Those designs can be improved just by following the datasheet.. it doesn't even take a minute. To check what the recommendation is...
The maximum voltage for 7805 is 25volts.. so just by supplying it 30v ,, ahh sketchy stuff.. you are overloading the ic...
Lets say you want 500mA current .. well that would be 12.5watts.. that little thing can't withstand it...
A regulator always needs a input cap close to input and reverse protection diode.. none of the basic things are even met...🤣🤣
Please don't do it...
This schemaatic hàs more errors then all other chematics on this channel combined.
This is unholy
Забыл все поставить! 😂
Электролитические конденсаторы на входе и выходе, а так же керамические конденсаторы 0.1-0.3мкФ шунтирующие вход и выход каждого линейного стабилизатора.
Теплоотвода нет!
Защиты никакой нет!
Красиво, но бесполезно! 😊
Проще на одном регулируемом стабилизаторе, собрать схему с регулировкой напряжения от 2.4 до 28 Вольт.
Не всегда это проще например как у бп атх когда надо несколько напряжений разом с небольшим током, а вот то что охлада нет это да, немного не продуманно
Расскажите пожалуйста зачем нужны шунтирующие конденсаторы?
Какую функцию они выполняют?
@@MorriartiНе дают возбудится стабилизаторам
N'oublie pas les glaçons 😢😅
Good but in case of overload or short it would burn the device being charged or powered.
or just use a LM317 and a potentiometer for 0 to 30 volts
Right 👍
Correction: 1.25 - 40V
Or a lm337 for more current, use a TO3 package with a heating for 3 amps.❤
Depends if you want any value of voltage in the range or if you just need _standard_ voltages as those provided by the 78xx, 79xx series of regulators.
If you are powering logic circuits, you *_don't_* want an adjustable voltage.
It means : 1. You risk blowing up the logic circuit, 2. You have the inconvenience of setting the voltage each time and accurately.
You then need a multimeter.
You are missing the point. The ideea is to have various voltages SIMULTANEOUSLY, so you'll be able to power multiple devices from one power supply.
@@florinpandele5205
You can have multiple voltages concurrently by having multiple LM317's.
The decision to use an LM317 or 78xx or 79xx isn't based on whether you need multiple voltages simultaneously but is based on whether the voltage(s) you need are "standard" fixed voltages that can be provided by the 78xx, 79xx series or whether you want a different and adjustable voltage.
Here it is possible for the power supply to provide multiple voltages of fixed voltages concurrently so I do agree that the original poster has missed the point.
Чел, сделал, молодец.
А теперь открой даташит на любой стабилизатор и угадай, что ты забыл добавить.
Can you pless tell what he forgot to add i do know that for 5v its going to dissipate 25v worth of heat.
regulators required capacitors for stopping outputoscillation.This movie may be fake.
@@animemafia2085
Each Regulators are Required Input/output capacitors for stopping oscillation.See data sheet. @@animemafia2085
@@animemafia2085capacitors
По моему это конденсаторы да?
دائرة غير عملية الدخل 30فولت ومنظم ال5فولت سيبدد ق25فولت وسترتفع درجة حرارته وسيتلف بوقت قليل نفس الشي لمنظم ال9والبقية
Можно сделать последовательное включение стабилизаторов😜
اولا هاد تضيع عالي للطاقة ثاني (البور دسبيشن) او التبديد الطاقة عالي على منظم ال5 اكتر شي وبعده ال9 والقانون يقول بانه لا يجب وضع جهد على منظم الجهد اكثر من جهد الخرج بمرتين كحد اقصى يعني مثلا منظم ال9فولت 12فولت تغذية كافية وكتير عليه هنا التبديد 3فولت فقط
Hi👋🤠; The "LMxxxx" series regulators are passive and Do Not shunt excess voltage to ground like a "Zener Diode" so no series dropping resistor is not needed and no extra current is being drawn. I do think though that stableizing capacitors should be used 🤔😉👍👍
Com um auxílio de um dissipador de calor bem robusto vazado com um cooler para fazer a refrigeração do calor. Deve evitar o sobreaquecimento. Já que um dos Ci gera 1A de corrente.
@@СергейБельский-г4ь я тоже про это подумал. Кстати - частенько сам так делаю. Правда - с кондёрами по входу/выходу.
Now i just need to buy a bench power supply with at least 30v DC to use this 😂
Great device for the winter
Сгорит даже в Якутии при -60С
Why you donot use any heatsink with transitors
These are not transistors
Low current only.
Хорошая печка получилась!
Плохая печка, маломощная :-)
Нужно ставить в последовательную цепочку, 15в стаб питать от 24в, 12в от 15в, 10в от 12 и тд, а то 9, 8, 5 вольтовые при подаче 30 вольт будут чувствовать себя очень плохо.
А зимой как отапливаться тогда?
Правильно!
This man : What is heat..! I don't know..! 😮
What is energy?
What is power?
Principle of conservation of energy
Чепуха полная! Даже школьник так делать не будет!
Крен5 или 7805 от подачи 30 вольт. Просто пыхнет.
Это раз. А про остальное сначало нужно посматреть дата шиты на крен, прежде чем их вот так цеплять,
А где все теплоотводы?
Not possible without cooling. Especially the 5V regulator. The positive rail is behind the cooling fin. This ist not so clever, because you are risking a short circuit and you are not longer able tu put cooling between the LMs and the PCB. And where are the caps? The regulators will ring like hell. Think first, do once.
Thats a good example how to NOT do it! IN-Output and Filter condenators are missing as fuses as adequate cooling especially with the high input voltage for the low voltage regulators. Half of them are running out of specs and will faster than you think burn out. Correct way would be a transformator with different secundary outputs, each about 3 Volts above the specific regulator. So about 8V for the 5V regulator 12V for the 9V regulator, 15V for the 12V regulator and so on
Very good video. But for this puspose, I would recommend an BUK-converter. It´s more efficient.
Perfect heater 🎉
I'm from India (your all video watch)
Fevkaladenin fevkinde bir eser oluşmuş. Tebrikler
Thanx for your video
А тепер згадайте фізику, подивіться даташит, і переробіть цей витвір. По перше розвернути в іншу сторону, від великої напруги і до меншої. По друге всі кренки ставте послідовно, щоб на кожній з них була якомога менша різниця потенціалів. Плюс пару електролітів, одну плівку або кераміку, і як мінімум один діод. Не забуваемо про радіатори, або один, та через діелектричну проставку. Все, тепер цей виріб правильний і надійний.
Всё то хорошо, но тогда получится на самы первый 24в нагрузка всех остальных ляжет.
@@TheSorvig 20 мА погоды не сделают
@@igorzherebiatev5751какие 20ма ? Каждый стабилизатор рассчитан на 1А, а на самый первый будет сумма всех.Это Ампер 6 минимум.
@@igorzherebiatev5751Всё, я думал он последовально все соединил, от высшего напряжения к нижнему.А он параллельно от общего источника питания.Тогда другая проблема, 5В стабилизатор от 24 вольт будет себя чувствовать очень не хорошо
@@TheSorvig их и надо последовательно, с отбором мощности с какого-то одного. Если их параллельно, то никакого радиатора не хватит для крен5, а 7824 едва работать будет
Excellent heater for miniature kettle for gnomes.
Muy buena tu estufa
great voltage regulator ever!! good job
WOW! It isn't often you get to see so much "WRONG!" in one video. Are you trying to burn down your house? Because that's how you burn down your house, Cheryl...
right out of the gate it's garbage. The thickness of the tracks is not enough for reliable operation. you didn't strengthen them in any way. There are no filter capacitors. therefore, no one needs this simple scheme, because it does not fulfill its functions.
What about input VCC?
If you do not adjust it for each regulator you will use, the power output available for the lower voltages will be too low.
To much voltage drop across regulators and too much heat dissipation.
😱🙈
Never use this design!
Extremely useful!!!… for a rocket/ward head circuit only meant to last a total of/no more than 10 minutes in flight, and even that may be too much 🤣
No capacitors, no diode reverse protections, no heat sinks for dissipation. Im definitely adding this to my saved list of circuits, so I can rebuild it correctly 😂
The most masterful part of this circuit is the self etched board (which I need to analyze on a still frame to make sure is truly correct, given this video) 😂
Cheers boys 🍻
LL200
DC Input Voltage: 40V max.
Peak Input Voltage: 60V max. for 10ms
Output Voltage Range: 2.85 to 36V
Output Current Range: 0.1 to 2A
Perfect 👌
Sempre usei furador de placa. Só agora me dei conta de que não precisa 😮
Volt metre ile voltaj alabilirsin ama istikrarsız ve kararsız bir devre ayrıca ısınma sorunu var bu devrede
Overclock yapılamılayacak bir sisteme sıvı sogutma gereksiz degilmi sizce de
i feel bad boosting this video's engagement but i have to comment that it didnt lie, it is a multi output voltage regulator power supply, it didnt say regulated anywhere in the title so it it isnt a lie
Power efficiency left the chat
arbeite gute 👍👍👍
Тем временем здоровые люди берут один 7805, переменный резистор и цифровой индикатор напряжения и собирают на нем регулируемый источник питания от 5 до 22 Вольт. 😂
Дизайн гаражной сборки, даже 5 минут работы может не выдержать...
am I the only one who sees this, the stabilizers are on the +24V path, without any insulator
Yes, only you😂
Because they are not.
хорошо паяется чистая медь)
You must change the circuit by reversing the order of the regulators by connecting them in the waterfall: foods on 7824 with 30 volts, with the exit of the 24 foods on 7818, with the exit of 7818 foods on 7815 and so on. This system will also divide the heat produced evenly.
At least with this design it would be in cascade, so you take advantage of the other job, but the 7805 to reduce from 30v, at minimum I'll recommend this solution.
Зафер, идея занимательная, но имеет ряд недостатков. :)
Если нет вольтметра для плавной регулировки выходного напряжения и нужен ряд определённых, фиксированных значений напряжений на выходе, то не проще ли подключать соответствующие стабилитроны к LM317Т ? :)
This has been made for views and comments to maximise user engagement for the algorithm. It is not a serious project.
I would of put a heat sink strip across the top.
Also , as the project is good , the Adjustable LM317T would give the voltages outlined here , or even add the LM317T as well.
Se puede con alambres, sin la placa?
Amazingly, which board is that?
Giriş voltajı dc mi ac mi?
🎉🎉🎉😊😊😊😊😊❤❤❤❤❤❤❤
Volt. Sem amperagem, adianta de quê?
Обогреватель мы уже научились делать. Теперь давайте о стабилизации напряжения. 😂😂😂
Dude has the capability to provide 8 amps of current but look at that single GND line.
😂😂🤣🤣
Where are filtering Capacitors?
I feel like this could have been done off a 120v to 24v transformer then a series of resistors making a voltage divider down to 5v
Cuanto es el voltaje de entrada amigo, y que mosfet son
Çok başarili👏🏻
Да ты прям целый блок питания собрал, осталось ещё отрицательную полярность собрать 🤗
Pero de cuantos amperes de salida tiene?
Идея на 2, плата громоздкая, можно было использовать 1 стабилизатор с возможностью регулировки и резисторы для выбора напряжения, конденсаторов сглаживающих нет, ну и самое главное ужасное КПД, ведь чтобы из 10в получить 5 например нужно половину мощности рассеять, уже давно есть dc-dc преобразователи
Handy if you actually need all of those voltages.
Lm317 is a best option instead this one. Only one potentiometer and generate variable voltage
Muito bom esse projeto de fonte, várias voltagem em uma fonte só... Só falta fazer uma boa filetagem com uns capacetes de 10.000mf ou mais por 50 ou 63 volts.
not less than 100V 😂
Lm317 can be used for variable voltage output
Yg dibawah 10v apa gak panas bang?
Kalau input dc ke ic regulator 24v harusnya tidak
If we give 30 volt input then the regulator ic's 7805 to 7812 may be burn because I was used 7805 at 15 volt sorce this was burnt.
How do u make each output isolated for audio circuits
Tribble circuit, you need a pulsed step down converter and no liner voltage regulator
Bro, ampere por salida? Gracias 👍🏻🤗🇻🇪
it seems, the ampere follows the dc input
this way it's easy....
On croyais que la connaissance c'est un échange.
Mais puisqu'il est devenu commercial.
On laisse ces gens vivres entre eux.
Le cercle fermé.
Merci
12 volt u 24 volt yapmak istyorum neler kullanmalıyım bir videonuz varmı tşkler
Very wrong in so many levels !!!
Я уже представляю, как эта сборка будет греться при нагрузке
the power path explodes at 2A+ 😂
Garbage!!! Where all the heat is going?? And that’s only one of at least 10 different problems you have with this piece of junk gaste of components
And when you need power it makes boom xD
Voltagem de entrada destes reguladores,pelo manual dos fabricantes somente o dobro da tensão de saída ( no máximo). Então o 7805 a tensão de entrada é de 10volts. E não 30 volts!
Why not use zener diode
Can you supply pcbs & parts?.
รหัสDCและอุปกรมีไรมังคับ
Heatsinks: Am I a joke to you?
All the other missing components: 👆
Muy interesante.Pero cuanta mas sea la direncia entre entrada y salida,eso afecta al regulador,esa diferencia se convertira en calor,por decir a asi.(siendo que se alimente a todos con la misma fuente,Xd)✌️
WOULD YOU LIKE TO MAKE ELEVATOR CIRCUIT. i HAVE A CIRCUIT MADE ALREADY BUT NO PARTS. iT REQUIRE A LATCHING RELAY WHICH HOLD THE POWER WITHOUT VOLATGE.. output voltage
Love you zafer ❤❤
Good but only 1.5 ampear output this circuit😢 need higher ampear circuit board
1.5A ist just with propper cooling. this design would get nowhere close to that. Remember with the 78XX the excess voltage is converted to heat. So for the 7805 at 30V that would be 25V loss. 25V*1,5A=37,5W in heat losses!
Eficiencia en su maximo explendor, que año estamos? Y ya que estamos, vamos a eliminar la inyeccion electronica, los catalizadores, las fuentes electronicas, las luces led, los correctores de potencia... Porque ir para adelante si podemos hacia atras, montaña abajo
Всё это чудо будет дико греться,если мало-мальски нагрузить
❤très bien je suis content puis je avoir plus formation ?
You can buy adjustable voltage regulators
That pcb has some mistake, those thin tracks won't deliver good enough grounding and power, it will oscilate as hell.
на подаче сколько вольт?
Op knows nothing about what they’re doing here
7805 в даташите сказано входное напряжение до 35в но как показывает практика он будет очень сильно нагреватся. Нет конденсаторов на входе и на выходе, а так же диода (анодом на выход, катодом на вход). Ещё радиатора тут очень кстати. А вообще можно убрать все это и на одном lm317 получить напряжение от 1.2в до 37в
And all of them are touching common VCC trace with their cases, which are GND...
wall mounted king
Only a thing, the most of 78xx have connectivité between pin base and the disipador part. If yu push on the 78xx you will have a mess because generated a dead Short
I think it was designed with wc
Very low efficiency. Regulable DC-DC converter is better and cheap.
It's a good method if you want to burn your 78xx.s. Power supply manufacturers produce complex circuits because they are stupid yes lol.