tp4056 | tp5000 | tp5100 | charging module | lithium cell charging module | tp4056 vs tp5000
HTML-код
- Опубликовано: 14 окт 2024
- by mistake I said mega hertz 😜..
Its miliampere hour. =( mah)
Please ignore it. Just focus the content
Of video. I hope I am able to clear it.
Thank u for ur supporting 😊👍
Sir, pls. don't mistake me , if i could correct you. I think it is, ( mah) is "milli ampare hour" and not milli Hertz.
Yeah, correct 😂
Are daiya juban fisalne se galti hui aii😅
Bhai ye to baar baar galti kar rhe hai ,Daya malum to Karo koun sa nasha hai ye😢
Mah= Mega hertz ❌ Mili amp hour ✅
By the way your information helped me a lot thanks
Right
good explanation.
As I understood from your video...
1.
TP4056 is battery charging controller
and
DW01A + FS8205A is used for ( overcharge protection , over discharge protection and short circuit protection) .
DW01A + FS8205A is BMS or BMS is something else ?
what is the role of BMS (battery management system).
2. As you said TP5100 is batter then TP4056 , but TP5100 module don't have any battery protection e.g (DW01A+FS8205A)
1200 mah wale lithium ion battery me bmsl lagana jaruri ki kewal charging module bas thik rahega
Sir TP 4056 3 module series me lagakar 3 ya 4 cell charge kar sakte hain.
Bhai mein nimh ke 1.2 v ke 3 cell series me charge karta hu 3.6 v bana ke tp 4056 se is se koi masla to nhi bn sakta na
For TP5000, do we need external BMS for EV grade batteries?
It is milliampere per hour, normally said mAh. Herts is the measurement of frequency whereas volt, ampere, watt measure electricity.🤔
I am little bit confused that if i use TP 4056 charging socket for charging then should i connect it directly with any charger or required 5v charger specifically
Tp4056 is only charging module which control the battery charging only. Input voltage should 5-8 v( always max than charging vol. i.e,4.2v.) Can use any mobile charger of 5v to 8v. Not max than that. 12V charger will damage the tp4056
Dear sir mere pass 3000mah,18650 ki 3 battery hai to tp5100 se battery parallel connect karke charge hogi kya? Aur use mobile charger matlab 5 watt 1 ampere se charge kar sakte hai kya?
Tp5100 - 1s - 2amp output, & 2s -1 amp output deta hai. Matlab Aap 2 cells ko series karke charge kar sakte hai. 8.4 v output. Input 12v dena hoga 8.4v output ke liye. & heat sink bhi use karna hoga 5100 module pe.
Sir, output pin seperate not found in 5100 like Tp 4056, only charging and Battery point available, so can we take output from same pins of Battery ?
Yes
4.2v 5amphere k liye konsa module milega
Smps power supply
Mega hertz kha se aa gaya?
Sir aap sonu nigam ji gana apni awaz mai try kijiye, achha lage ga,
Battery.paralal ya series me charge karni he
Its For series .. The charging voltage will double
Really informative sir.
You are basically wrong on some aspects. TP4056 single ic module is a charger. It protects from over charging. You say it won't. Secondly the two ICs, protects battery from over discharging. 2) milli amps you say hertz?, Where did you study electronics?
@2:03 Mega Hertz ???? Really ????? New Invention I guess,,,
Don't say anything he is technical grandfather 😂
aree yaar... bolne me mistake ho jati hai kai baar. 😀😀 content ko sajho .. yeha lakho subscribers wale bhi galat bolte hai. 👍👍
@@technicaldada5384Lakho subscriber wale galat bole gi to kya app hame galat information dogi kya
6000mah charging module ?
Sir 1.2 volt battery charger krne ke liye modul btaye
Aliexpress!
3.2 vot 100ah prismatic cell ko charge karna ho to kaise kare....charger kaha milega.....
Smps/ Transformer based power supply.use kar sakte hai. Jisse charging voltage 3.7v rakhna hai. And charging current jo bhi max ho Apke smps ki..
12v battery ke liye konsa module sahi hai pls.
Bms module
4s/ 3s bms module use karna padega apko
26000 MHz?????
Sir who is best
all details & comparison in the video . watch complete video ,all doubts clear.
tp4056 for li-ion cells . (with over cjarge protection)
tp5000 for Lpf cells(without overcharge protection -need extra bms install for tp5000)
tp5100 can charge two li-ion cell together -8.4v output. but need install extra bms for overcharge protection.
All cells are not in megahertzs dear please clear your knowledge all cells are in milli ampere hour capacity ( mah) it's not a frequency which is measured in megahertzs 😊😊😊😊
Yes, you are right
Hello sir, can I connect 3pcs or more of TP5000 in pararel to get more current...?
No. For getting more current to charge fast u can update the tp5000 module by changing the resistors.. Get upto 2amp per module.
See video @ 9.27min.
try to make a ppt slides for this kind of information for next videos@@technicaldada5384
5100 me 12v aur kitne amp ka max input de skte hai
Amp aap kitna bhi dijiye voltage constant hona chahiye, module a/c to charging automatic amp. Le lega., max 3 amp de sakte hai. Matlab. 1cell ke liye max 2amp charging current lega & 2 cells in series ke liye max 1amp . input vol max 12v .
Thanks
Sir bms me do alag mah ki cell charge kr skte hai kya
@@abbyysingh kar sakte hai, but kam mah wala pehle full charge hoke damage ya phatne ka dar rahega. Generally its not recommended.
Okay thanks
2000 mAh = 2000 milli ampear hour
Can you share the your notes, which you have prepared.
You can screen short it at starting point.
😂😅mega hertz
And see the Channel name 😂😂
अरे भाई दूसरे को सिखाने से पहले mili ampere hours (mAh) को तो समझ ले पहले !!! mAh का मतलब mega hartz नहीं होता है !!!
Fantastic video ❤
Battery ampere may hota hay vai....frequency may nahi😂😂😂
Phle knowledge leke aa bhai. Ek Bar mistake hota hai lekin tune to mah ko mega hrtz hi naam de diya. Mili Ampere Hour kise kahte hai tab. Puri video me galat information de di. Naam phle jan lo. Phir information do.
False information
Sar aapka number milega?
Dada good work