I have fp4, when I try to edit the created map I get the message "fuelpak user editing of this table is not permitted" what am I doing wrong, what's going on?
Thanks for the video. What about if I’m running the Bassani exhaust !! I can see the option in the video shows only 3 types of exhaust and mine is not there !!
I just put big radius pipes on my 2016 softail. Stock 103 high output with a KN filter in the factory breather. I immediately noticed I lost my bottom end torque. My engine braking isn’t as strong either. Will a tune get that back ??? I wasn’t expecting to gain power with the pipes but I didn’t expect to lose my low rpm torque
Just got mine in the mail today. Installing map in a few minutes on my 2021 Fatboy 114 FLFBS. Vance & Hines PCX Big Radius 2-into-2 Full Exhaust System Black Question i have is does this site my original map and can restore it if i ever wanted to?
I just put big radius pipes on my 2016 heritage softail. I immediately noticed I lost the bottom end torque. Noticed my engine braking isn’t near as strong too. Bike runs good but that stump pulling hit of torque feels gone. Will a tune fix that ?
Hello: I want to buy the FUELPAK P4 ECU for my HD 48 year 2015, I have V&H SHORTSHOTS STAGGERED exhausts but I have an ARLEN NESS MINI 22 air filter, can I map the bike with that air filter? Or it must be a V&H air filter. THANK YOU SO MUCH
On my 07 sporty 1200, it will only connect in the on position. Then tells me in ‘low’ while on tender. Painful and not as quick and easy as the vid makes out!
I believe it is because all the supported models already have a stage 1 intake fitted from factory. At least that is the case with the softails. I hope that helps
I want to run V&H exhaust dampers on my 2021 StreetBob 114. This year they have sensors for the rear exhaust mufflers as well as on the headers. Will using the FP4 eliminate the need for these sensors? And if so, what do I do with these sensors + wiring?
Bought it for my 2011 Dyna Fat Bob. It will not pass the initial update setup screen. I’ve sent Vance and Hines 2 emails and no answer. Very frustrating experience. I was very excited and looked forward to buying more Vance and Hines products but so far their support hasn’t supported their product.
Have you tried calling them. I just had one put on my 07 ultra but I have not picked the bike up yet. I keep seeing negative stuff and I’m getting anxious that I’m going to get the stop wasting money speech from my wife again
@@rjj5075 I had found an email from one of the techs on a Harley Forum. He guided me through the whole step. The initial setup kept asking to put my bike on Acc but by doing that it would shut off the FP4. I left it in IGN with the kill switch on and it updated. I was successful in installing the closest tune to my setup. I tried auto tune in “advanced setup” and lowered the temp to work and also put o2 sensor voltage to .8v. It seemed to work. From what he told me. Auto tune is only supposed to learn what it needs. So you may not get the same result as everyone else. Typically the preset tunes are close to perfect when flashed
@@mobkinq I just bought the bike. It was completely original with 18,000 miles on it. I’m getting a thunderheader installed and I put a stage one screaming eagle breather on it. I hope this thing works. I was told by the shop that I left it at that they could do a tune on it. Then I’m out of town for a week on business and they say that they can’t tune it and I need a tuner. I asked what they recommend and they said the FP3. Then he said oh they are making a new one. That’s what you need. So I bought it. Now I’m terrified after reading reviews. I’m starting to wish I hadn’t sold my FXR. Throw some keys in and head out.
@@rjj5075 yeah… I too was disappointed after reading reviews and having the first issue straight out the box. I hadn’t done much research on it until after I clicked checkout online. Nonetheless, it seems my bike is running good. I don’t care much for all the other features like sensor info. I don’t like to ride with my phones screen the whole time unless in auto tune. I personally didn’t feel a difference after tuning. I’ve owned 1000cc sport bikes with sprockets and ecu flash. so anything compared to that seems minimal. But It does tell you if your engine is running rich/lean. You always have the chance to get it right using auto tune. And have the opportunity to change idle, develop pop, and rev limit
I installed the FP4 on my 2017 FLHTP after I had the S&S oil and cam chest installed. I put a K&N filter unit and Cobra neighbor hater slip ns on also. The throttle response is great and the bike runs cooler. I did not change the cam but I was looking for more reliability . I would suggest this to anyone doing some basic changes to their bike. BUSHMASTER6
FP4 is garbage. It doesn't function at all and customer service will talk you in circles to avoid a return/refund. It's always going to be your bike battery or phone os that is preventing the tuner from working.
I have fp4, when I try to edit the created map I get the message "fuelpak user editing of this table is not permitted" what am I doing wrong, what's going on?
This is exiting news. Thankyou for the presentation.
Thanks for the video. What about if I’m running the Bassani exhaust !! I can see the option in the video shows only 3 types of exhaust and mine is not there !!
Hey did you ever find out if you can just run bassani on it?
I just put big radius pipes on my 2016 softail. Stock 103 high output with a KN filter in the factory breather. I immediately noticed I lost my bottom end torque. My engine braking isn’t as strong either. Will a tune get that back ??? I wasn’t expecting to gain power with the pipes but I didn’t expect to lose my low rpm torque
This is probably a dumb question… Do you keep the FP4 installed in the connector port after you install the new map?
Just got mine in the mail today. Installing map in a few minutes on my 2021 Fatboy 114 FLFBS.
Vance & Hines PCX Big Radius 2-into-2 Full Exhaust System Black
Question i have is does this site my original map and can restore it if i ever wanted to?
I just put big radius pipes on my 2016 heritage softail. I immediately noticed I lost the bottom end torque. Noticed my engine braking isn’t near as strong too. Bike runs good but that stump pulling hit of torque feels gone. Will a tune fix that ?
Do you have to have Internet to do it or just my android
Hello:
I want to buy the FUELPAK P4 ECU for my HD 48 year 2015, I have V&H SHORTSHOTS STAGGERED exhausts but I have an ARLEN NESS MINI 22 air filter, can I map the bike with that air filter? Or it must be a V&H air filter. THANK YOU SO MUCH
This is probably a stupid question… Do you leave the FP4 installed in the port after you install the new map.
Is there a way to adjust the idle rpm? Like you could with the FP3
I have head pipes, slip-ons, and high flow air cleaner. Will this work on my '12 Road Glide Ultra if I swap the cam?
On my 07 sporty 1200, it will only connect in the on position. Then tells me in ‘low’ while on tender.
Painful and not as quick and easy as the vid makes out!
Can this be used if I buy one used or us it a one bike and done deal?
Why does the fp4 not have anything in the app about intakes?
I am here for the same information. I used an Iphone and got my VH Short Shots tuned. I couldn't figure out the intake.
I believe it is because all the supported models already have a stage 1 intake fitted from factory. At least that is the case with the softails. I hope that helps
Jesus how long does the bootloader downland take its been 1 hr on my 2022 roadglide special and still not done!!!
can i use this tuner on my 2020 street glide?
do it work on Jekill and Hyde ?
Where is the option for throttle progressivity?
2021 RG where is the hookup?
I want to run V&H exhaust dampers on my 2021 StreetBob 114. This year they have sensors for the rear exhaust mufflers as well as on the headers. Will using the FP4 eliminate the need for these sensors? And if so, what do I do with these sensors + wiring?
Hi did you find out about the sensor
can the app show you AFR in Lambda?
Why can’t a look and edit maps for IOS? I like the product but I’m frustrated that app hasn’t been updated for IOS system..
Bought it for my 2011 Dyna Fat Bob. It will not pass the initial update setup screen. I’ve sent Vance and Hines 2 emails and no answer. Very frustrating experience. I was very excited and looked forward to buying more Vance and Hines products but so far their support hasn’t supported their product.
Have you tried calling them. I just had one put on my 07 ultra but I have not picked the bike up yet. I keep seeing negative stuff and I’m getting anxious that I’m going to get the stop wasting money speech from my wife again
@@rjj5075 I had found an email from one of the techs on a Harley Forum. He guided me through the whole step. The initial setup kept asking to put my bike on Acc but by doing that it would shut off the FP4. I left it in IGN with the kill switch on and it updated. I was successful in installing the closest tune to my setup. I tried auto tune in “advanced setup” and lowered the temp to work and also put o2 sensor voltage to .8v. It seemed to work. From what he told me. Auto tune is only supposed to learn what it needs. So you may not get the same result as everyone else. Typically the preset tunes are close to perfect when flashed
@@mobkinq I just bought the bike. It was completely original with 18,000 miles on it. I’m getting a thunderheader installed and I put a stage one screaming eagle breather on it. I hope this thing works. I was told by the shop that I left it at that they could do a tune on it. Then I’m out of town for a week on business and they say that they can’t tune it and I need a tuner. I asked what they recommend and they said the FP3. Then he said oh they are making a new one. That’s what you need. So I bought it. Now I’m terrified after reading reviews. I’m starting to wish I hadn’t sold my FXR. Throw some keys in and head out.
@@rjj5075 yeah… I too was disappointed after reading reviews and having the first issue straight out the box. I hadn’t done much research on it until after I clicked checkout online. Nonetheless, it seems my bike is running good. I don’t care much for all the other features like sensor info. I don’t like to ride with my phones screen the whole time unless in auto tune. I personally didn’t feel a difference after tuning. I’ve owned 1000cc sport bikes with sprockets and ecu flash. so anything compared to that seems minimal. But It does tell you if your engine is running rich/lean. You always have the chance to get it right using auto tune. And have the opportunity to change idle, develop pop, and rev limit
What happened to the autotune function?
mine wont connect after loading base map. no auto tune. junk
You really need to tell what it won't do. I bought mine for my 21 street glide and won't do decell pop or throttle response, just start with.
I installed the FP4 on my 2017 FLHTP after I had the S&S oil and cam chest installed. I put a K&N filter unit and Cobra neighbor hater slip ns on also. The throttle response is great and the bike runs cooler. I did not change the cam but I was looking for more reliability . I would suggest this to anyone doing some basic changes to their bike. BUSHMASTER6
"No Response, try it again" every time I try to autotune. Very frustrating.
Is this still a problem for you?
Is it really IOS compatible? Others buyers are saying no that it’s Android only.
I installed an FP4 on my 21 Street Bob tonight, about 3 hours ago, and it connects to my iPhone just fine.
Many features on the FP4 don’t work with IOS, if it connects at all, just go to the App Store and check out the reviews, problems are numerous.
FP4 is garbage. It doesn't function at all and customer service will talk you in circles to avoid a return/refund. It's always going to be your bike battery or phone os that is preventing the tuner from working.