I needed a new sprocket and clutch for my 420cc motor so I legit bought all of these clutches plus 4 sprockets, then today this video is in my recommended
I’m rebuilding my mini bike and have already bought 4 separate pieces that don’t fit… 😂 And now I only have a week before deadline to order new parts. If I mess up one more time I’m screwed
They really need to mention the rpm range of engagement...I built a stage 4 212cc predator..with a much bigger cam... these typical clutches engage around 2200-2500 rpms...not sure if gopower sells the 3500 rpm clutches or not, but I will say, that they are available on the market...
I want to put a horizontal shaft engine on a lawnmower frame to PULL a cutting deck, what would be the BEST axle sprocket tooth size to use with one of these clutches?
You guys have a video how to remove a clutch. I try to remove the bolt and the crankshaft just spins. Is there a special tool that that holds. It while the bolt can loosen?
Do you have a video explaining what clutch I would need for motor size increments? Such as if I get a go kart and it has a 5 horse motor and I wanna put a 10 horse how do I know how heavy of a clutch to get
I’m building a old gokart and it has a sprocket on the axle but I’m putting a China made Honda clone on it, I’m guessing I measure the sprocket on the axel also tooth to tooth to make sure I get the right chain also? Am I right or does that matter
Hello I just naught a power fist 79cc engine I’m looking for a clutch but I want to make sure the clutches key fits on the motor and I’m not sure how to figure that out the key slot on the engine doesn’t go the whole way back
I have a mini bike with a predator 212 bought it used. Chain snapped I think I tightened to much . Now trying to find which chain I should buy. I measured the inside spoke point to point it's 3/8 . Now u say I need a 35 inch one or ?
Are there different clutches. Do they make a heavy-duty clutch for go Kart or are they all they same? I have a 2 seat Go Kart and because of the weight and being a 5hp engine, I was looking for a heavy-duty clutch.
I found some anomalies regarding overall width (my original 3/4" 420 off of a 196 hisun, a new replacement came in the mail, 3/4" bore 420, for my predator 224). My question, should the bronze bushing extend slightly past the pto shaft, so the clutch bolt washer contacts that 1st, not the crankshaft end? Sorry if the question sounds dumb, I'm new to small engines..
Is there anything I need to know on upgrading to better clutches, and the pros/cons of 6, 4, or 3 puck clutches? (I believe that term applies here aswell)
I have a question so my minibike bogs down because we took the governor off and will be going fast will be doing good and then all of a sudden it will just like stay at one speed instead of speeding up to its normal speed how do I fix this
Jetted carb, less restrictive intake, less restrictive exhaust, stronger valve springs, billet flywheel, billet rod, billet pushrods, and you might as well as advance the timing while you're at it.
Just bought a Coleman CT200U and there is nothing in the owners manual (specifications) about the size of the centrifugal clutch.. can someone help me ? Thanks !!
Awesome, thanks! I´m building a Gokart for my kids with a 3hp motor with a 5/8" shaft. What chain standard is the easiest to find parts for? I´m gonna need to try out a variety sprockets to make the speed just right. My wife would kill me if the kids ran over the cat. Thanks!
My Tecumseh 6.0hp on a Murray explorer frame seems to start moving right after I start it so I have to hop on quick after I pull the starter cord. I’m pretty sure my idle adjustment on the carb is broken and the clutch may be bad. It also sputters at low rpm and lurches sometimes. After I get going it runs really good (25-30 mph), but it seems like after I slow down for a turn and try to step back on it, it will hesitate and then only get up to about 20mph. The left rear wheel (nearest to drive belt) has a slight wobble as well. Also needs to be shook forwards and backwards after it’s parked in order to move it. Brakes don’t engage until 3/4 of the way to the floor. Any advice/lists for what needs to be repaired/replaced would be greatly appreciated.
I'm building a bike and I have a 38 tooth sprocket on the rear I'm turning a Schwinn chopper bike I took the front fork and the rear end and I basically need to know what size centrifugal clutch do I need I know it's 3/4 bore but I need to know what size spacing in teeth that I need for my 38 tooth sprocket and my clutch
How u doin????i have a 212cc predator motor n a 3/4 clutch but im wondering if u can give me da size of the bolt i need for the clutch....thanks on asvance
Lol I’m using a12 tooth clutch with a 420 chain no master link and it actually runs but not a good idea Cain grinding her end there but I’m ordering the right set up now going back to 10 tooth with 420 chain 😂
i have the second clutch from left, that is a 12T 3/4inch clutch on a 208cc 6.5hp Briggs and Stratton engine with a 60T rear sprocket for 5:1 gear ratio. My kart weighs 140kg with driver and has 11 inch rear tyres. When we run the kart, the clutch gets extremely hot and sparks are seen coming out of it but we stopped it from burning out and turning blue/purple. I have oiled it properly and checked the chain tension but still it gets extremely hot in 15 minute runs. We try to run it at full throttle to let it cool down but now the friction pads have expanded and get engaged at low rpms. Please suggest some ideas to make it run longer and cooler.
If you have a CVT they run pretty much dry so you may want to check to see if you need oil in the first place, look up some videos to be double sure because if the parts are sliding too much with oil or grease then they will get really hot and get little traction.
If my go-kart that i got doesnt have a clutch, would i need to just measure the shaft from the engine? I have the chain, but no clutch on my Murray Go-Kart. I currently have a Tecumseh OHH60 engine.
I’m a little late but if you have a Murray explorer with the Tecumseh 6.0hp that is badass. I just found my uncles old one in the barn and finished getting it running but the clutch is going bad and I’m replacing it soon. If you still need the info I’m looking at mine tomorrow and I can give you specs of mine
I am using a 12T, 3/4" clutch from Go Power Sports for an engineering design project in college. I was wondering if you know the width of the clutch? Working with limited space and can't find a spec sheet anywhere online. Thanks!
You need the 3/4 in centrifugal clutch bore.. my son put a 212 predator hemi on his Coleman and had to buy another centrifugal clutch which is t10 3/4 in
Hello I’m making a small mud buggy project. And I’m trying to stay away from belt to eliminate slippage issues. Do you think one of those centrifugal clutches or a disk clutch would still work and engage submerged in water and mud ?
Thanks bro big help
5 year old video just saved my project 😅 appreciate that
Great to hear!
I needed a new sprocket and clutch for my 420cc motor so I legit bought all of these clutches plus 4 sprockets, then today this video is in my recommended
I’m rebuilding my mini bike and have already bought 4 separate pieces that don’t fit… 😂 And now I only have a week before deadline to order new parts. If I mess up one more time I’m screwed
God forbid and I feel like they do this in prosose to us
This helped me choose the right chain, and the right clutch! Soon I'll get your torque convertor!
They really need to mention the rpm range of engagement...I built a stage 4 212cc predator..with a much bigger cam... these typical clutches engage around 2200-2500 rpms...not sure if gopower sells the 3500 rpm clutches or not, but I will say, that they are available on the market...
Loved this! Gave me the info I needed and right to the point.! The perfect video. Thank you.
Thanks now I don't have to keep looking all over the place to find one lol
Can someone please tell me if you can buy a clutch for a predator 8hp motor.
I want to put a horizontal shaft engine on a lawnmower frame to PULL a cutting deck, what would be the BEST axle sprocket tooth size to use with one of these clutches?
40 chain to wide for 420 clutch i got from go power sports. The masterlink rubs chain guide on clutch.
You guys have a video how to remove a clutch. I try to remove the bolt and the crankshaft just spins. Is there a special tool that that holds. It while the bolt can loosen?
U had the the the chain numbers back words 5/8 clutch bore take 41,420,40 chain
3/4 bore take chain 35
Do you have a video explaining what clutch I would need for motor size increments? Such as if I get a go kart and it has a 5 horse motor and I wanna put a 10 horse how do I know how heavy of a clutch to get
This video was helpful i ordered a 5/8 clutch for my Colman CT100U i think it is the right clutch for it my old clutch bore isn't 3/4.
5/8” should be right for that model
@@GoPowerSports it is thank you.
Sweet video really helpful I couldn't figure out the size chain I need it that really helped out after all these years OMG thanks a lot!!
I’m building a old gokart and it has a sprocket on the axle but I’m putting a China made Honda clone on it, I’m guessing I measure the sprocket on the axel also tooth to tooth to make sure I get the right chain also? Am I right or does that matter
Yes, measure the sprocket from tooth to tooth to help figure out your chain size.
@@GoPowerSports thank you
i need help witch one would i buy for honda gx 160
Hi there I have a gx160 Honda 5.5hp what size would I need?
Thanks again
Thank you for letting me know that would help me build my go kart
Hello I just naught a power fist 79cc engine I’m looking for a clutch but I want to make sure the clutches key fits on the motor and I’m not sure how to figure that out the key slot on the engine doesn’t go the whole way back
5hp Honda xr2600 160cc motor, what will fit?
I have a mini bike with a predator 212 bought it used. Chain snapped I think I tightened to much . Now trying to find which chain I should buy. I measured the inside spoke point to point it's 3/8 . Now u say I need a 35 inch one or ?
I need a 3/4 35 to match with my chain and sprocket. Does it matter if I choose 10 or 12 teeth?
Are there different clutches. Do they make a heavy-duty clutch for go Kart or are they all they same? I have a 2 seat Go Kart and because of the weight and being a 5hp engine, I was looking for a heavy-duty clutch.
I found some anomalies regarding overall width (my original 3/4" 420 off of a 196 hisun, a new replacement came in the mail, 3/4" bore 420, for my predator 224). My question, should the bronze bushing extend slightly past the pto shaft, so the clutch bolt washer contacts that 1st, not the crankshaft end? Sorry if the question sounds dumb, I'm new to small engines..
I was looking at y’all clutch to determine which and I need thank you for the video Cajunland Church point Louisiana
witch clutch would you recommend for a KT 100 with tapered shaft?
I ordered the 3/4” bore and it’s too small for my torque converter. Do I need an 1” bore
Bro this short video, is soooo much knowledge.. man thank you.
Thank you!
Is there anything I need to know on upgrading to better clutches, and the pros/cons of 6, 4, or 3 puck clutches? (I believe that term applies here aswell)
What clutch do I need for a ct200 u ex ? A 3/4 or a 5/8 don’t know what clutch to order .
I have a question so my minibike bogs down because we took the governor off and will be going fast will be doing good and then all of a sudden it will just like stay at one speed instead of speeding up to its normal speed how do I fix this
Jetted carb, less restrictive intake, less restrictive exhaust, stronger valve springs, billet flywheel, billet rod, billet pushrods, and you might as well as advance the timing while you're at it.
Which clutch will give more power vs speed?
Thank you building a drift trike this helps a lot
No problem!
I’m trying to find a 15T clutch for my 196cc 420 Chain, anybody got the link? I just found out I have a 12T already
We mainly see these higher tooth counts for the #35 chain.
A question I have a 1997 talhoe 4w.drive automatic it sometimes make a noise front of truckthat when it warms up the noise goes away
Can you tell me it sounds like a in line noise
i bought a clutch but the sproket is to thick for the chain what do i do?
I need the size of the 2 screws in the back for the 3/4 35 they keep going loose and I lost the them and my clutch is kinda weird now
What size clutch does the governor have
Have you asked him yet? Ello Governor!
I have a Coleman ct200u-a that’s the 5/8 right?
Thanks, I had no idea to to match the clutch with the right chain. Can't can also count the teeth on the clutch?
I have a Jenkins 16hp 420cc motor which one is best to buy for motor and chain thank you
Jenkins motor
Hi I have a 16 hp 420cc motor which one is best for that motor
I’m just getting into minibike stuff this definitely helped
can a 3/4 centrifugal clutch handle 225cc engine? if not, what size of centrifugal clutch should i use?
It will, you may need stiffer springs in that clutch though.
@@GoPowerSports thanks guys have a good day
which clutch do I need for a 224cc predator engine clutch
My Honda gx200 doesn’t have a key slot when I slide on my clutch what do I do??! Just file down key on clutch and put it on and use set screws???!???
Without the keyway, your clutch won't spin with the crankshaft. I would just get a new engine.
What one do I need for my predator 420 on my yerf dog go kart?
Is it a big performance upgrade going from 35-420?
Just bought a Coleman CT200U and there is nothing in the owners manual (specifications) about the size of the centrifugal clutch.. can someone help me ? Thanks !!
I have a 10HP motor I am pulling of an old wheel horse and putting on a go kart. Anyone know what size clutch that is?
If I have a strong engine on my go kart what which one would you recommend
What about 1" ? I have a gx240 Honda.
Awesome, thanks! I´m building a Gokart for my kids with a 3hp motor with a 5/8" shaft. What chain standard is the easiest to find parts for? I´m gonna need to try out a variety sprockets to make the speed just right. My wife would kill me if the kids ran over the cat.
Thanks!
#35 and #420 chain are the most popular options. You will have more luck with the #35 chain with that clutch setup.
@@GoPowerSports great, thanks! 35 chain it is. Would you happen to know at what rpm’s the Max-Torque clutch ”activates”?
What Is the Full name of the first clutch on the left. Plz i need to buy that one but idk what to search for that.
My Tecumseh 6.0hp on a Murray explorer frame seems to start moving right after I start it so I have to hop on quick after I pull the starter cord. I’m pretty sure my idle adjustment on the carb is broken and the clutch may be bad. It also sputters at low rpm and lurches sometimes. After I get going it runs really good (25-30 mph), but it seems like after I slow down for a turn and try to step back on it, it will hesitate and then only get up to about 20mph. The left rear wheel (nearest to drive belt) has a slight wobble as well. Also needs to be shook forwards and backwards after it’s parked in order to move it. Brakes don’t engage until 3/4 of the way to the floor. Any advice/lists for what needs to be repaired/replaced would be greatly appreciated.
the brake thing is common on those. mine has to be re adjusted every now and then. your clutch sounds like its rusted engaged.
So the 3/4 clutch should fit my 5.0 hp tecumseh correct????
I'm building a bike and I have a 38 tooth sprocket on the rear I'm turning a Schwinn chopper bike I took the front fork and the rear end and I basically need to know what size centrifugal clutch do I need I know it's 3/4 bore but I need to know what size spacing in teeth that I need for my 38 tooth sprocket and my clutch
Same I'm just going to send it
go buy a bit of 35 chain and 40 chain and see what fits better.
How can I find a 22mm bore clutch
No clue on this. We have a 1" bore which may be too big for that 22mm.
How u doin????i have a 212cc predator motor n a 3/4 clutch but im wondering if u can give me da size of the bolt i need for the clutch....thanks on asvance
Freddy Mendoza I’m pretty sure 5/8 or 5/16
Where u can find the fietst clutch
First
Lol I’m using a12 tooth clutch with a 420 chain no master link and it actually runs but not a good idea Cain grinding her end there but I’m ordering the right set up now going back to 10 tooth with 420 chain 😂
how do i find the right sprocket for my 420 7/8 clutch?
Mark Jones what clutch did you get
So I would need a 3/4 For a Honda gx200?
Wgst clutch do I run on a Honda gx160
My sprokit is 1/8 what size chain do I need
Would it be a 3/4" bore ??
i have the second clutch from left, that is a 12T 3/4inch clutch on a 208cc 6.5hp Briggs and Stratton engine with a 60T rear sprocket for 5:1 gear ratio. My kart weighs 140kg with driver and has 11 inch rear tyres. When we run the kart, the clutch gets extremely hot and sparks are seen coming out of it but we stopped it from burning out and turning blue/purple. I have oiled it properly and checked the chain tension but still it gets extremely hot in 15 minute runs. We try to run it at full throttle to let it cool down but now the friction pads have expanded and get engaged at low rpms. Please suggest some ideas to make it run longer and cooler.
Hitesh Arora clutches get very hot no matter what
Lower gear ratio - put a bigger sprocket on your axel so you’re like 8 or 9:1
If you have a CVT they run pretty much dry so you may want to check to see if you need oil in the first place, look up some videos to be double sure because if the parts are sliding too much with oil or grease then they will get really hot and get little traction.
I need a clucth with a 1 inch bore for a size 50 chain but can't find one
Not sure they exist
Does centrifugal clutch work like a freewheel in a bicycle? When you stop pedaling, the bicycle rolls away in neutral?
Yeah and when u give some gas it spins
What about if you have a #520 chain what can you do ?
Hey i need help from anyone im going to make a go kart and my camshaft is 2.5cm what centerfigual seize do i need?
I have a briggs motor 5Hp and i don’t know If 3/4“ is the right one?
Soo measure it lmao
some 5hp briggs had 1" shafts.
What kind of cluch would I need for a Honda gx110?
If my go-kart that i got doesnt have a clutch, would i need to just measure the shaft from the engine? I have the chain, but no clutch on my Murray Go-Kart. I currently have a Tecumseh OHH60 engine.
I’m a little late but if you have a Murray explorer with the Tecumseh 6.0hp that is badass. I just found my uncles old one in the barn and finished getting it running but the clutch is going bad and I’m replacing it soon. If you still need the info I’m looking at mine tomorrow and I can give you specs of mine
I have a 420cc 13hp what do I need?
what if I have a belt driven Max torque centrifugal clutch?
can I change from a 10 tooth clutch to 12 of more?
I am using a 12T, 3/4" clutch from Go Power Sports for an engineering design project in college. I was wondering if you know the width of the clutch? Working with limited space and can't find a spec sheet anywhere online. Thanks!
Try going on eBay look up the clutch that you have and check the size there
What clutch would work for a predator 301 stage 1
Did you end up figuring out which one it needed?
So what your saying is all 40 41 and 420 chains are all the exact same
Same pitch but different widths (thickness)
Yep i just found that out i had to make the sprocket skinnier to fit the chain i used but it worked out nice
I want this but ı can’t where ı get. You can help mi ?
What size sprocket for the 670
I just bought my predator 212 and have a 2020 Coleman CTU EX and the clutch doesn’t fit. Hopefully I can get one soon
You need the 3/4 in centrifugal clutch bore.. my son put a 212 predator hemi on his Coleman and had to buy another centrifugal clutch which is t10 3/4 in
What if I just have a 196cc do I need a 3/4 for a ct200uex?
My clutch is bigger than 3/4 and it’s a Briggs and stratton motor it’s a 12tooth it’s a5hp horse power
What do I do?
Great video!
Super helpful, thanks
what do you guys lube clutch with? high temp grease or motor oil which lasts?
v z slap some wd40 on that bitch and send it dude.
(No but seriously don’t do that)
You left out the 1/2 inch I have a late model coleman that has a 10 tooth half inch clutch
how do i remove a stuck (frozen) clutch w/o a puller?
Ramiro Garcia crow bar and some wd-40
buy a puller or make a tool. don't go using crow bars you may hurts yourself.
Can I put a 3/4 clutch on a 96CC predator
No
so how do you measure the shaft. to see what size clutch you need??
Use your measuring tape on shaft end. You want to measure dead center of shaft end, from side to side.
Most 6.5hp are 3/4 shaft.
Hope that helps
@@BeastOuncelifeian what clutch should I get for a 301cc predator engine?
Where can I buy a good quality clutch and minibike parts from I have a 5.5 hp tecumseh 7/8 shaft and I need a jack shaft
Arcturus Welding & Fabrication gopowersports.com
@Go Kid if I have 3/4" shaft would I get a clutch with a 3/4" BORE
what kind do i have to use on a briggs 2hp( older engine)???
@Nathan Reich okay thank you so much
5/8 on most briggs engines lower than 5hp.
Okay so if I have a 3/4" shaft what size bore do I get
3/4". The shaft and the bore should match.
Funny thing is. I bought a clutch and chain from you all exactly what I needed got the wrong fucking thing. It just came in today actually.
What size for a motovox 80cc
Most likely a 5/8" or 16mm.
thanks
Where can i buy a centrifugal
Hello I’m making a small mud buggy project. And I’m trying to stay away from belt to eliminate slippage issues. Do you think one of those centrifugal clutches or a disk clutch would still work and engage submerged in water and mud ?