sir sabe ng mechanic dito samen di daw crankshft ang tinangal mo camshaft daw...ano ba talagA sir paliwanag naman sir pls mor2x from zamboanga del norte salamat
would you know where the fuel purge valve is located , the work shop gives picture or different engine . I'm having hesitation issues when tank is above halve full and sometimes when i clean map sensor goes for a whole then hesitates no codes .
Hi, thank you for this video Would a dodgy map sensor cause rev limiting? I’m limited to 3k rpm but rarely on occasion it lets me rev above and the boost seems to actually kick in Anyway I’m going to give it a clean and if that doesn’t work I’m going to have someone look at the wiring I have read error code p0107 low voltage to sensor Also I may have the old version of suction control valve but I don’t think that would cause the limiting, I do stall sometimes at low rpm though
hey I have the same problem with my 4jj1, did you resolve it I can't seem to find the issue? limits my revs to 3 grand most the time but on the odd occasion it allows boost to kick in but only for a short period of time, and then when I let the car idle for roughly more than 10 seconds it stops making boost again, any help would be appreciated
@@jamillajennings6631 hi yeah I got my map replaced but it was actually just a loose plug, like the plug wasn’t seated properly in so just driving would cause it to sometimes disconnect partially I got lucky I reckon, here and there I’ve had it go back into limp mode but turning it off and on again it fixes itself I’ve also got the old scv so that causes some problems and I need to replace it too but for now she runs alright as far as I can tell
Sir, bakit sa akin Hindi na pumapalo Yung rpm tsaka speedo meter pag on ko sa susi normally papalo sya tapos Wala Ng reading di na gumagana Ang speedo tsaka rpm fuel gauge tsaka Ang temp. Gauge
Sir jung sana makita mo message ko...ask ko lang ung engine ko hanggang 2000 lang rpm kahit ibirit mo... 4jj1 altera... maraming salamat sa mga video mo marami ako natutunan...
@@JongTheDIYCarGuy tnx sir sana magawa ko.. di gumagalaw rpm ko tumataas lang sya kapag nag switch on ako pero kapag nka andar na ang makina wala na nka baba lang sya walang function.. 4jj1 dmax boondock
bro its more better if you can include the subtitles we love you diy , and i have done to subscribe as we are also the isuzu dmax lover, i own the dmax diablo 2015 3.0 Cc
sir sabe ng mechanic dito samen di daw crankshft ang tinangal mo camshaft daw...ano ba talagA sir paliwanag naman sir pls mor2x from zamboanga del norte salamat
oo nga camshaft sensor yon hehehe
would you know where the fuel purge valve is located , the work shop gives picture or different engine . I'm having hesitation issues when tank is above halve full and sometimes when i clean map sensor goes for a whole then hesitates no codes .
hi bro, there is nothing to connect at baro sensor nozzle? and is it okey if let it not connected?
Theres non. Just an open nipple
May check engine din po ako same intake air temperature hign, ano po possible cause?
Hi, thank you for this video
Would a dodgy map sensor cause rev limiting? I’m limited to 3k rpm but rarely on occasion it lets me rev above and the boost seems to actually kick in
Anyway I’m going to give it a clean and if that doesn’t work I’m going to have someone look at the wiring I have read error code p0107 low voltage to sensor
Also I may have the old version of suction control valve but I don’t think that would cause the limiting, I do stall sometimes at low rpm though
Check for boost leaks
@@JongTheDIYCarGuy will do cool
hey I have the same problem with my 4jj1, did you resolve it I can't seem to find the issue? limits my revs to 3 grand most the time but on the odd occasion it allows boost to kick in but only for a short period of time, and then when I let the car idle for roughly more than 10 seconds it stops making boost again, any help would be appreciated
@@jamillajennings6631 hi yeah I got my map replaced but it was actually just a loose plug, like the plug wasn’t seated properly in so just driving would cause it to sometimes disconnect partially
I got lucky I reckon, here and there I’ve had it go back into limp mode but turning it off and on again it fixes itself
I’ve also got the old scv so that causes some problems and I need to replace it too but for now she runs alright as far as I can tell
Sir, bakit sa akin Hindi na pumapalo Yung rpm tsaka speedo meter pag on ko sa susi normally papalo sya tapos Wala Ng reading di na gumagana Ang speedo tsaka rpm fuel gauge tsaka Ang temp. Gauge
Sir jung sana makita mo message ko...ask ko lang ung engine ko hanggang 2000 lang rpm kahit ibirit mo... 4jj1 altera... maraming salamat sa mga video mo marami ako natutunan...
Check mo intake system mo baka may boost leak yan, sensors like maf baka madumi
Is that crankshaft position sensor. What's the one at bottom by flywheel ?I
Speed sensor is also located at the bottom
Thanks Mr Jong.my 4jj1 has hard starting and rev counter not working. Appreciate
Has got sensor in middle off camshafts and speed sensor bottom rear left
Glow plug light is fast on of when cold.ECTS faulty?
I'm struggling Mr Jong
Do you have pdf rebuild guide for this engine? Please
I will look for it. I know someone posted this from my group before
@@JongTheDIYCarGuy thanks alot for your respond
Paps kailangan pa bang idisconnect.ang negative ng battery before removing those sensors.?
Sa akin hindi ko na inaalis. No issues naman
Sir jong good am di ko kasi makita ung baro sensor. Stock po. 2017 dmax. Tnx man
Sa may air filter box
Good morning sir jung
Tanong lang sana
Kung saan tayo nakaka bili ng pcv diaphragm ng 4jj1
Parihas tayo ng makina alterra lang itong akin
Salamat po
Sa Lazada po, kkabili ko lang po
Thanks alot for your affairs
Sir may ganyang mga sensors din ba ang innova D4D engine?
Meron po
@@JongTheDIYCarGuy saan po ba nakalocate? Di ko kasi kabisado ung sensors na iyan po salamat
Baro sensor usually nasa airbox or around intake manifold. Camshaft near the timing belt
@@JongTheDIYCarGuy salamat sir, hahanapin ko po mamaya. Hehe
sir may video ba sa rpm sensor? san ba location ng rpm sensor po? ty sana may video
Cranshaft sensor boss. Sensor determines the revolution per minute
@@JongTheDIYCarGuy tnx sir sana magawa ko.. di gumagalaw rpm ko tumataas lang sya kapag nag switch on ako pero kapag nka andar na ang makina wala na nka baba lang sya walang function.. 4jj1 dmax boondock
Baka may wire nabalatan yan boss
bro its more better if you can include the subtitles we love you diy , and i have done to subscribe as we are also the isuzu dmax lover, i own the dmax diablo 2015 3.0 Cc
Sir how about isuzu 4jj2 puede kang mag sample just asking po
4jj2?
Hello Mr Jong
Tnong lng po sir yan po ba ang location ng crankshaft sensor 4jj1 engine?
Halos tabi ng idler pulley
Ah salamat po sir..akala ko kc yng nasa klid ng engine block sa may starter motor side.
Sir pano maglinis ng pcv valve ng 4jj1?
4 screws located near the nipple. Pop it open check mo diaphragm if buo. Malinis mo lang jan is yung spring
Camshaft sensor ang tinanggal mo hindi crankshaft sensor...
Kala ko camshaft tsk